Focused-ion-beam chemical vapor deposition (FIB-CVD) is an excellent technology for forming three-dimensional nanostructures. Various diamond-like-carbon (DLC) free-space-wirings have been demonstrated by FIB-CVD using a computer-controlled pattern generator, which is a commercially available pattern generator for electron-beam (EB) lithography. The material composition and crystal structure of DLC free-space-wiring were studied by transmission-electron microscopy and energy-dispersive x-ray spectroscopy. As a result, it became clear that DLC free-space-wiring is amorphous carbon containing a Ga core in the wire. Furthermore, the electrical resistivity measurement of DLC free-space-wiring was carried out by two terminal electrodes. Au electrodes were fabricated by EB lithography and a lift-off process. The electrical resistivity was about 100 Ω cm at room temperature.

We used SU-8 shrinkage to fabricate strained graphene resonators to produce a high quality factor in a graphene resonator. A-few-layer graphene resonators were fabricated on a trench of an SU-8 resist. These resonators were clamped with diamond-like carbon (DLC), which was deposited by using focused-ion-beam chemical vapor deposition (FIB-CVD), and trimmed by using FIB etching. Annealing was used to apply tensile strain to the graphene resonators because SU-8 shrinks drastically. We also observed an increase in resonant frequency and quality factor in these graphene resonators after annealing. At room temperature, the quality factor of the best sample exceeded 7,000 for a resonator length of 10 µm.

No abstract

We studied the fabrication of free-designed three-dimensional (3D) structures by using focused-ion-beam chemical-vapor deposition. The 3D structures are fabricated by scanning 30 keV Ga+ ion-beam-assisted deposition in a 1×10−4 Pa phenanthrene atmosphere. The scanning pattern and blanking signal of the ion beam are generated by a 3D computer-aided-designed model using a computer pattern-generating system. This 3D pattern-generating system is able to fabricate overhang and hollow structures by setting suitable parameters (for example, plot pitch, dwell time, time interval of irradiations, and priorities of scanning). In this article, we demonstrate the performance of a 3D pattern-generating system by fabricating a 1:100 000 000 scale model of the Enterprise spaceship, a microring, a moth’s eyelike structure, and a morpho butterflylike structure with 200 nm spacing.

Three-dimensional (3D) nanostructures on a glass capillary have a number of useful applications such as manipulators, actuators, and sensors in the various microstructures. We observed a phenomenon that two diamondlike-carbon pillars on a tip of glass capillary fabricated by 30 keV Ga+ focused-ion-beam-chemical vapor deposition (FIB-CVD) with a precursor of phenanthrene vapor was able to work as a manipulator during FIB irradiation. It became clear that it was caused by electronic charge repulsion between two pillars, which accumulated electric charge by FIB irradiation. By applying this moving mechanism, we have developed a 3D nanomanipulator and actuator on a tip of glass capillary by FIB-CVD. Furthermore, in situ observations of movement for a 3D nanomanipulator and actuator have been demonstrated by applying voltage onto a Au-coated glass capillary.

High-sensitivity charge detection using antisymmetric vibration in two coupled GaAs oscillators is demonstrated. The antisymmetric mode under in-phase simultaneous driving of the two oscillators disappears with perfect frequency tuning. The piezoelectric stress induced by a small gate-voltage modulation breaks the balance of the two oscillators, leading to the re-emergence of the antisymmetric mode. Measurement of the amplitude change enables detection of the applied voltage or, equivalently, added charges. In contrast to the frequency-shift detection using a single oscillator, our method allows a large readout up to the strongly driven nonlinear response regime, providing the high room-temperature sensitivity of 147 e/Hz0.5.

Three-dimensional nanostructures on a glass capillary have a number of useful applications such as manipulators and sensors in the various microstructures. This time, we have demonstrated the fabrication of a nozzle nanostructure on a glass capillary for a bio injector by 30 keV Ga þ focused-ion-beam assisted deposition with a precursor of phenanthrene vapor and etching. It has been demonstrated that nozzle nanostructures with various shapes and sizes have been successfully fabricated. An inner tip diameter of 30 nm on a glass capillary and a tip shape with an inclined angle have been realized.

Articles you may be interested inDynamic characteristics control of DLC nano-resonator fabricated by focused-ion-beam chemical vapor deposition J.Piezoresistive effect in the three-dimensional diamondlike carbon nanostructure fabricated by focused-ion-beam chemical vapor deposition J. Vac. Sci. Technol. B 28, C6F38 (2010); 10.1116/1.3504584Resistivity change of the diamondlike carbon, deposited by focused-ion-beam chemical vapor deposition, induced by the annealing treatment Development of a regeneration-type neural interface: A microtube guide for axon growth of neuronal cells fabricated using focused-ion-beam chemical vapor deposition Mechanical characteristics and its annealing effect of diamondlike-carbon nanosprings fabricated by focused-ionbeam chemical vapor deposition