This work demonstrates a design approach which enables the fabrication of fully integrated radio frequency (RF) and millimetre-wave frequency direct-conversion graphene receivers by adapting the frontend architecture to exploit the state-of-the-art performance of the recently reported wafer-scale CVD metal-insulator-graphene (MIG) diodes. As a proof-of-concept, we built a fully integrated microwave receiver in the frequency range 2.1-2.7 GHz employing the strong nonlinearity and the high responsivity of MIG diodes to successfully receive and demodulate complex, digitally modulated communication signals at 2.45 GHz. In addition, the fabricated receiver uses zero-biased MIG diodes and consumes zero dc power. With the flexibility to be fabricated on different substrates, the prototype receiver frontend is fabricated on a low-cost, glass substrate utilising a custom-developed MMIC process backend which enables the high performance of passive components. The measured performance of the prototype makes it suitable for Internet-of-Things (IoT) and Radio Frequency Identification (RFID) systems for medical and communication applications.

The ORCID identification number(s) for the author(s) of this article can be found under https://doi.org/10.1002/adma.202108473.Over the past two decades, research on 2D materials has received much interest. Graphene is the most promising candidate regarding high-frequency applications thus far due to is high carrier mobility. Here, the research about the employment of graphene in micro-and millimeter-wave circuits is reviewed. The review starts with the different methodologies to grow and transfer graphene, before discussing the way graphene-based field-effecttransistors (GFETs) and diodes are built. A review on different approaches for realizing these devices is provided before discussing the employment of both GFETs and graphene diodes in different micro-and millimeter-wave circuits, showing the possibilities but also the limitations of this 2D material for highfrequency applications.

We demonstrate the design, fabrication, and characterization of wafer-scale, zero-bias power detectors based on two-dimensional MoS2 field effect transistors (FETs). The MoS2 FETs are fabricated using a wafer-scale process on 8 µm thick Polyimide film, which in principle serves as flexible substrate. The performances of two CVD-MoS2 sheets, grown with different processes and showing different thicknesses, are analyzed and compared from the single device fabrication and characterization steps to the circuit level. The power detector prototypes exploit the nonlinearity of the transistors above the cut-off frequency of the devices. The proposed detectors are designed employing a transistor model based on measurement results. The fabricated circuits operate in Ku-band between 12 and 18 GHz, with a demonstrated voltage responsivity of 45 V/W at 18 GHz in the case of monolayer MoS2 and 104 V/W at 16 GHz in the case of multilayer MoS2, both achieved without applied DC bias. They are the best performing power detectors fabricated on flexible substrate reported to date. The measured dynamic range exceeds 30 dB outperforming other semiconductor technologies like silicon complementary metal oxide semiconductor (CMOS) circuits and GaAs Schottky diodes.

Diodes made of heterostructures of the 2D material graphene and conventional 3D materials are reviewed in this manuscript. Several applications in high frequency electronics and optoelectronics are highlighted. In particular, advantages of metal–insulator–graphene (MIG) diodes over conventional metal–insulator–metal diodes are discussed with respect to relevant figures‐of‐merit. The MIG concept is extended to 1D diodes. Several experimentally implemented radio frequency circuit applications with MIG diodes as active elements are presented. Furthermore, graphene‐silicon Schottky diodes as well as MIG diodes are reviewed in terms of their potential for photodetection. Here, graphene‐based diodes have the potential to outperform conventional photodetectors in several key figures‐of‐merit, such as overall responsivity or dark current levels. Obviously, advantages in some areas may come at the cost of disadvantages in others, so that 2D/3D diodes need to be tailored in application‐specific ways.

No abstract

No abstract

No abstract

Thickness-modulated lateral MoS2 diodes with an extracted benchmark cutoff frequency ( fc) of up to 126 GHz are implemented and fully characterised. Fabricated diodes demonstrate on-off current ratio of more...