1 Introduction Global energy demand is predicted to exceed 30 TW by 2050, about double the present value [1]. This predicament, known as the TeraWatt challenge, and concern over anthropogenic climate change, resource availability ("peak energy") and energy security have all increased the interest in renewable energy (hydroelectric, wind, solar, geothermal and biomass) [2]. One of the most promising renewable energy technologies is solar photovoltaics (PV) which convert sunlight directly into electrical energy. Although the resource potential of PV is enormous, it currently constitutes a small fraction (<1%) of global energy supply [2]. One of the main factors limiting the widespread adoption of PV is its low energy density, low efficiency, and relatively high cost in comparison to other energy technologies. This means that current PV technology can only compete in areas of high insolation or by government incentives such as feed-in tariff programs.One of the most relevant metrics for PV devices is the power conversion efficiency (PCE); that is, the efficiency with which sunlight can be converted to electrical power. A significant effort in PV research today aims to improve PCE while simultaneously reducing (or, at least, not significantly impacting) production cost. The vast majority of
The effect of sulfur passivation on core-shell p-n junction GaAs nanowire (NW) solar cells has been investigated. Devices of two types were investigated, consisting of indium tin oxide contact dots or opaque Au finger electrodes. Lateral carrier transport from the NWs to the contact fingers was achieved via a p-doped GaAs surface conduction layer. NWs between the opaque contact fingers had sidewall surfaces exposed for passivation by sulfur. The relative cell efficiency increased by 19% upon passivation. The contribution of the thin film grown between the NWs to the total cell efficiency was estimated by removing the NWs using a sonication procedure. Mechanisms of carrier transport and photovoltaic effects are discussed on the basis of spatially resolved laser scanning measurements.
Patterned arrays of self-assisted GaP nanowires (NWs) were grown on a Si substrate by gas source molecular beam epitaxy using various V/III flux ratios from 1-6, and various pitches from 360-1000 nm. As the V/III flux ratio was increased from 1-6, the NWs showed a change in morphology from outward tapering to straight, and eventually to inward tapering. The morphologies of the self-assisted GaP NWs are well described by a simple kinetic equation for the NW radius versus the position along the NW axis. The most important growth parameter that governs the NW morphology is the V/III flux ratio. Sharpened NWs with a stable radius equal to only 12 nm at a V/III flux of 6 were achieved, demonstrating their suitability for the insertion of quantum dots.
We describe methods of Ga droplet consumption in Ga-assisted GaAs nanowires, and their impact on the crystal structure at the tip of nanowires. Droplets are consumed under different group V flux conditions and the resulting tip crystal structure is examined by transmission electron microscopy. The use of GaAsP marker layers provides insight into the behavior of the Ga droplet during different droplet consumption conditions. Lower group V droplet supersaturations lead to a pure zincblende stacking-fault-free tip crystal structure, which improved the performance of a nanowire-based photovoltaic device.
InP nanowires with InAsP quantum dots (QDs) were grown by molecular beam epitaxy on a Si (111) substrates. The structure of the InAsP QDs were studied using transmission electron microscopy, allowing the development of a model where QD growth occurs by group V desorption from the surrounding substrate surface. Micro-photoluminescence was performed at 10 K showing emission at 1.47-1.49 eV from the InP wurtzite structure, and various emission peaks between 0.93 and 1.33 eV attributed to the QDs. The emission was tuned by the QD composition. The effectiveness of an AlInP passivation shell was demonstrated via an improvement in the photoluminescence intensity. Spectrally-resolved photocurrent measurements at room temperature demonstrated infrared response due to absorption within the QDs. The absorption red-shifted with increasing As composition of the QD.
The native oxide at the surface of III-V nanowires, such as InAs, can be a major source of charge noise and scattering in nanowire-based electronics, particularly for quantum devices operated at low temperatures. Surface passivation provides a means to remove the native oxide and prevent its regrowth. Here, we study the effects of surface passivation and conformal dielectric deposition by measuring electrical conductance through nanowire field effect transistors treated with a variety of surface preparations. By extracting field effect mobility, subthreshold swing, threshold shift with temperature, and the gate hysteresis for each device, we infer the relative effects of the different treatments on the factors influencing transport. It is found that a combination of chemical passivation followed by deposition of an aluminum oxide dielectric shell yields the best results compared to the other treatments, and comparable to untreated nanowires. Finally, it is shown that an entrenched, top-gated device using an optimally treated nanowire can successfully form a stable double quantum dot at low temperatures. The device has excellent electrostatic tunability owing to the conformal dielectric layer and the combination of local top gates and a global back gate.PACS numbers:
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.