This review discusses about biomimetic medical materials for tissue engineering of bone and cartilage, after previous scientific commentary of the invitation-based, Korea-China joint symposium on biomimetic medical materials, which was held in Seoul, Korea, from October 22 to 26, 2015. The contents of this review were evolved from the presentations of that symposium. Four topics of biomimetic medical materials were discussed from different research groups here: 1) 3D bioprinting medical materials, 2) nano/micro-technology, 3) surface modification of biomaterials for their interactions with cells and 4) clinical aspects of biomaterials for cartilage focusing on cells, scaffolds and cytokines.

To extract charges more efficiently through charge-transporting layers (CTLs), various dopants are necessary. Lithium bis­(trifluoromethanesulfonyl)­imide (Li-TFSI) is the most widely used dopant in electron- and hole-transporting layers. However, Li+ ions easily migrate into the perovskite and deteriorate the device performance. To address this issue, several efforts such as introducing a buffer layer have been tried, but the issue is still not fully resolved. Thus it is required to find a simple way without additional treatments. In this work, we propose a simple strategy to use defect-tolerant dopant in CTLs, sodium bis­(trifluoromethanesulfonyl)­imide (Na-TFSI), to improve both the efficiency and the stability of perovskite solar cells (PSCs). The PSCs with Na-TFSI for both the electron-transport layer and the hole-transport layer show the highest power conversion efficiency up to 22.4%. In addition, the device with Na-TFSI exhibited better long-term operating stability at 45 °C, maintaining >80% of the initial performance even after 500 h of continuous 1 sun illumination.

No abstract

BackgroundCellulose and its derivatives such as carboxymethyl cellulose (CMC) have been employed as a biomaterial for their diverse applications such as tissue engineering, drug delivery and other medical materials. Porosity of the scaffolds has advantages in their applications to tissue engineering such as more cell adhesion and migration leading to better tissue regeneration. After synthesis of CMC-poly(ethylene oxide) (PEO) hydrogel by mixing the solutions of both CMC-acrylate and PEO-hexa-thiols, fabrication and evaluation of a CMC-PEO gel and its film in porous form have been made for its possible applications to tissue regeneration. Physicochemical and biological properties of both CMC-PEO hydrogel and porous films have been evaluated by using physicochemical assays by SEM, FTIR and swelling behaviors as well as in vitro assays of MTT, Neutral red, BrdU, gel covering and tissue ingrowth into the pores of the CMC-PEO gel films. Degradation of CMC-PEO hydrogel was also evaluated by treating with esterase over time.ResultsChemical grafting of acrylate to CMC was verified by analyses of both FTIR and NMR. CMC-PEO hydrogel was obtained by mixing two precursor polymer solutions of CMC-acrylate and PEO-hexa-thiols and by transforming into a porous CMC-PEO gel film by gas forming of ammonium bicarbonate particles. The fabricated hydrogel has swollen in buffer to more than 6 times and degraded by esterase. The results of in vitro assays of live and dead, MTT, BrdU, Neutral red and gel covering on the cells showed excellent cell compatibility of CMC-PEO hydrogel and porous gel films. Furthermore the porous films showed excellent in vitro adhesion and migration of cells into their pore channels as observed by H&E and MT stains.ConclusionsBoth CMC-PEO hydrogel and porous gel films showed excellent biocompatibility and were expected to be a good candidate scaffold for tissue engineering.

Novel hydrogel composed of both chondroitin sulfate (CS) and gelatin was developed for better cellular interaction through two step double crosslinking of N-(3-diethylpropyl)-N-ethylcarbodiimide hydrochloride (EDC) chemistries and then click chemistry. EDC chemistry was proceeded during grafting of amino acid dihydrazide (ADH) to carboxylic groups in CS and gelatin network in separate reactions, thus obtaining CS-ADH and gelatin-ADH, respectively. CS-acrylate and gelatin-TCEP was obtained through a second EDC chemistry of the unreacted free amines of CS-ADH and gelatin-ADH with acrylic acid and tri(carboxyethyl)phosphine (TCEP), respectively. In situ CS-gelatin hydrogel was obtained via click chemistry by simple mixing of aqueous solutions of both CS-acrylate and gelatin-TCEP. ATR-FTIR spectroscopy showed formation of the new chemical bonds between CS and gelatin in CS-gelatin hydrogel network. SEM demonstrated microporous structure of the hydrogel. Within serial precursor concentrations of the CS-gelatin hydrogels studied, they showed trends of the reaction rates of gelation, where the higher concentration, the quicker the gelation occurred. In vitro studies, including assessment of cell viability (live and dead assay), cytotoxicity, biocompatibility via direct contacts of the hydrogels with cells, as well as measurement of inflammatory responses, showed their excellent biocompatibility. Eventually, the test results verified a promising potency for further application of CS-gelatin hydrogel in many biomedical fields, including drug delivery and tissue engineering by mimicking extracellular matrix components of tissues such as collagen and CS in cartilage.

In this article, a hybrid gel has been developed using sodium alginate (Alg) and α-tricalcium phosphate (α-TCP) particles through ionic crosslinking process for the application in bone tissue engineering. The effects of pH and composition of the gel on osteoblast cells (MC3T3) response and bioactive molecules release have been evaluated. At first, a slurry of Alg and α-TCP has been prepared using an ultrasonicator for the homogeneous distribution of α-TCP particles in the Alg network and to achieve adequate interfacial interaction between them. After that, CaCl2 solution has been added to the slurry so that ionic crosslinked gel (Alg-α-TCP) is formed. The developed hybrid gel has been physico-chemically characterized using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and a swelling study. The SEM analysis depicted the presence of α-TCP micro-particles on the surface of the hybrid gel, while cross-section images signified that the α-TCP particles are fully embedded in the porous gel network. Different % swelling ratio at pH 4, 7 and 7.4 confirmed the pH responsiveness of the Alg-α-TCP gel. The hybrid gel having lower % α-TCP particles showed higher % swelling at pH 7.4. The hybrid gel demonstrated a faster release rate of bovine serum albumin (BSA), tetracycline (TCN) and dimethyloxalylglycine (DMOG) at pH 7.4 and for the grade having lower % α-TCP particles. The MC3T3 cells are viable inside the hybrid gel, while the rate of cell proliferation is higher at pH 7.4 compared to pH 7. The in vitro cytotoxicity analysis using thiazolyl blue tetrazolium bromide (MTT), bromodeoxyuridine (BrdU) and neutral red assays ascertained that the hybrid gel is non-toxic for MC3T3 cells. The experimental results implied that the non-toxic and biocompatible Alg-α-TCP hybrid gel could be used as scaffold in bone tissue engineering.

Two random copolymers based on the (2,5-difluorophenylene)dithiophene and dialkoxybenzothiadiazole with benzodithiophene (P1) or thiophene (P2) as third conjugated bridges having sulfur and fluorine (S···F) and/or oxygen (S···O) non-covalent intramolecular interaction are synthesized and characterized. In despite of molecular weight difference over three times between both polymers, P1 and P2 possess similar solubility in organic solvents and thermal stability (Td~320 o C), which means probably due to that P1 with bulky alkylthiophene substituted benzodithiophene as a third conjugated bridge has less non-covalent intramolecular interaction than that of P2 with thiophene as a bridge. Both polymers were used as electron donors in bulk heterojunction organic photovoltaics (BHJ OPV) with PC71BM as an acceptor. From the photovoltaic measurements, it reveals that P2 shows higher power conversion efficiency (PCE) of up to 6.82% than that of P1 (2.44%). After 1,8-diiodooctane (DIO) treatments as a processing additive, the P1 and P2 devices show a significantly improved PCE of 5.95% for P1 and 7.71% for P2. The surface morphology analysis of the blend films using the atomic force microscope (AFM) reveals that P1:PC71BM film shows a macrophase separation, while the P2 film has a smooth morphology. After DIO treatment, morphology of both polymer blend films is improved with better bi-continuous nanosclae networks. Charge carrier mobilities through the space charge limited current (SCLC) method demonstrate that P2 with thiophene bridge has higher charge carrier mobilities than that of P1. In particular, inverted structured BHJ OPV with P2 exhibits a PCE of 8.50%, which is the highest PCE reported in the literature regarding random copolymers.

No abstract