In this paper we study the effect of contamination induced by fabrication process on laser damage density of fused silica polished parts at 351 nm in nanosecond regime. We show, owing to recent developments of our raster scan metrology, that a good correlation exists between damage density and concentration of certain contaminants for the considered parts.

We present an experimental realization with electrical composites of the thermal fuse model [D. Sornette and C. Vanneste, Phys. Rev. Lett. 68, 612 (1992)], proposed as a paradigm of dynamical rupture in heterogeneous media. An isolating polymer matrix is filled with conducting particles, and the particle-particle contacts evolve due to thermal expansion of the matrix as a function of the applied current I. Above a critical current, the electric resistance R increases as a power law of time to rupture R ϳ ͑t r 2 t͒ 2a , with a Ӎ 0.65, and the breakdown time t r scales as t r ϳ I 22 in agreement with the model. [S0031-9007(96)01260-4] PACS numbers: 62.20.Mk

Known for more than 40years, laser damage phenomena have not been measured reproducibly up to now. Laser resistance of optical components is decreased by the presence of material defects, the distribution of which can initiate a distribution of damage sites. A raster scan test procedure has been used for several years in order to determine laser damage density of large aperture UV fused silica optics. This procedure was improved in terms of accuracy and repeatability. We describe the equipment, test procedure, and data analysis to perform this damage test of large aperture optics with small beams. The originality of the refined procedure is that a shot to shot correlation is performed between the damage occurrence and the corresponding fluence by recording beam parameters of hundreds of thousands of shots during the test at 10Hz. We characterize the distribution of damaging defects by the fluence at which they cause damage. Because tests are realized with small Gaussian beams (about 1mm at 1∕e), beam overlap and beam shape are two key parameters which have to be taken into account in order to determine damage density. After complete data analysis and treatment, we reached a repeatable metrology of laser damage performance. The measurement is destructive for the sample. However, the consideration of error bars on defect distributions in a series of parts allows us to compare data with other installations. This will permit to look for reproducibility, a necessary condition in order to test theoretical predictions.

No abstract

No abstract

The Petawatt Aquitaine Laser (PETAL) facility was designed and constructed by the French Commissariat à l'énergie atomique et aux énergies alternatives (CEA) as an additional PW beamline to the Laser MegaJoule (LMJ) facility. PETAL energy is limited to 1 kJ at the beginning due to the damage threshold of the final optics. In this paper, we present the commissioning of the PW PETAL beamline. The first kJ shots in the amplifier section with a large spectrum front end, the alignment of the synthetic aperture compression stage and the initial demonstration of the 1.15 PW @ 850 J operations in the compression stage are detailed. Issues encountered relating to damage to optics are also addressed.

International audienceIn order to resolve problems concerning the understanding and the control of laser-induced damage of silica optical elements, a collaboration between the CEA and different university laboratories has been undertaken. Ultra-pure silica model samples, seeded with gold nanoparticles whose diameter did not exceed 5 nm, were prepared. The aim in using these samples was to observe the mechanism of damage initiation that could be attributed to inclusions of nanometric size. This paper presents the different steps encountered during this study: preparation of the samples, the laser-induced damage tests, the Nomarski and atomic-force microscope observations of this damage and a series of experiments using a time-of-flight mass spectrometer at Argonne National Laboratory. The experimental data are then interpreted, and, in particular, compared to numerical simulations. A very encouraging result is the existence of a pre-damage phase at very low fluences that is not detectable by classical optical devices. The experimental means developed for such model samples should be transposable to the analysis of industrial glasses

In our study, the laser-induced damage densities on a fused silica surface produced by multiple longitudinal mode (MLM) pulses are found to be higher than those produced by single longitudinal mode pulses at 1064 nm. This behavior is explained by the enhancement of the three-photon absorption due to the intensity spikes related to longitudinal mode beating. At 355 nm, the absorption is linear and an opposite behavior occurs. It can be explained with the help of a process involving thermomechanics coupled with the fine time structure of MLM pulses, leading to the possible annealing of part of the absorbent defects.