In this review article, we focus on the various types of materials used in biomedical implantable devices, including the polymeric materials used as substrates and for the packaging of such devices. Polymeric materials are used because of the ease of fabrication, flexibility, and their biocompatible nature as well as their wide range of mechanical, electrical, chemical, and thermal behaviors when combined with different materials as composites. Biocompatible and biostable polymers are extensively used to package implanted devices, with the main criteria that include gas permeability and water permeability of the packaging polymer to protect the electronic circuit of the device from moisture and ions inside the human body. Polymeric materials must also have considerable tensile strength and should be able to contain the device over the envisioned lifetime of the implant. For substrates, structural properties and, at times, electrical properties would be of greater concern. Section 1 gives an introduction of some medical devices and implants along with the material requirements and properties needed. Different synthetic polymeric materials such as polyvinylidene fluoride, polyethylene, polypropylene, polydimethylsiloxane, parylene, polyamide, polytetrafluoroethylene, poly(methyl methacrylate), polyimide, and polyurethane have been examined, and liquid crystalline polymers and nanocomposites have been evaluated as biomaterials that are suitable for biomedical packaging (section 2). A summary and glimpse of the future trend in this area has also been given (section 3). Materials and information used in this manuscript are adapted from papers published between 2010 and 2015 representing the most updated information available on each material.
Fast, simple, cost-efficient, eco-friendly, and design-flexible patterning of highquality graphene from abundant natural resources is of immense interest for the mass production of next-generation graphene-based green electronics. Most electronic components have been manufactured by repetitive photolithography processes involving a large number of masks, photoresists, and toxic etchants; resulting in slow, complex, expensive, less-flexible, and often corrosive electronics manufacturing processes to date. Here, a one-step formation and patterning of highly conductive graphene on natural woods and leaves by programmable irradiation of ultrafast high-photon-energy laser pulses in ambient air is presented. Direct photoconversion of woods and leaves into graphene is realized at a low temperature by intense ultrafast light pulses with controlled fluences. Green graphene electronic components of electrical interconnects, flexible temperature sensors, and energy-storing pseudocapacitors are fabricated from woods and leaves. This direct graphene synthesis is a breakthrough toward biocompatible, biodegradable, and ecofriendlily manufactured green electronics for the sustainable earth.
Noncontact electronic skin (e-skin), which possesses superior long-range and high-spatial-resolution sensory properties, is becoming indispensable in fulfilling the emulation of human sensation via prosthetics. Here, we present an advanced design and fabrication of all-graphene-based highly flexible noncontact e-skins by virtue of femtosecond laser direct writing (FsLDW). The photoreduced graphene oxide patterns function as the conductive electrodes, whereas the pristine graphene oxide thin film serves as the sensing layer. The as-fabricated e-skins exhibit high sensitivity, fast response-recovery behavior, good long-term stability, and excellent mechanical robustness. In-depth analysis reveals that the sensing mechanism is attributed to proton and ionic conductivity in the low and high humidity conditions, respectively. By taking the merits of the FsLDW, a 4 × 4 sensing matrix is facilely integrated in a single-step, eco-friendly, and green process. The light-weight and in-plane matrix shows high-spatial-resolution sensing capabilities over a long detection range in a noncontact mode. This study will open up an avenue to innovations in the noncontact e-skins and hold a promise for applications in wearable human-machine interfaces, robotics, and bioelectronics.
Flexible and stretchable strain sensors are in great demand for many applications like wearables and home health. This work reports a strain sensor fabricated using aerosol jet printing technology on a commercially available bandage to be used as a low-cost wearable. Laser light is explored to sinter the silver nanoparticle ink on low-temperature bandage substrate. The laser parameters, their effects on the microstructure of the film, and the resulting sensor performance are systematically investigated. The results showed that the sensor is stretchable, has good sensitivity, and stability for 700 cycles of repeated bending.
Fabrication of tissue engineering scaffolds with the use of novel 3D printing has gained lot of attention, however systematic investigation of biomaterials for 3D printing have not been widely explored. In this report, well-defined structures of polycaprolactone (PCL) and PCL- carbon nanotube (PCL-CNT) composite scaffolds have been designed and fabricated using a 3D printer. Conditions for 3D printing has been optimized while the effects of varying CNT percentages with PCL matrix on the thermal, mechanical and biological properties of the printed scaffolds are studied. Raman spectroscopy is used to characterise the functionalized CNTs and its interactions with PCL matrix. Mechanical properties of the composites are characterised using nanoindentation. Maximum peak load, elastic modulus and hardness increases with increasing CNT content. Differential scanning calorimetry (DSC) studies reveal the thermal and crystalline behaviour of PCL and its CNT composites. Biodegradation studies are performed in Pseudomonas Lipase enzymatic media, showing its specificity and effect on degradation rate. Cell imaging and viability studies of H9c2 cells from rat origin on the scaffolds are performed using fluorescence imaging and MTT assay, respectively. PCL and its CNT composites are able to show cell proliferation and have the potential to be used in cardiac tissue engineering.
Laser‐induced graphene (LIG) is a newly emerging 3D porous material produced when irradiating a laser beam on certain carbon materials. LIG exhibits high porosity, excellent electrical conductivity, and good mechanical flexibility. Predesigned LIG patterns can be directly fabricated on diverse carbon materials with controllable microstructure, surface property, electrical conductivity, chemical composition, and heteroatom doping. This selective, low‐cost, chemical‐free, and maskless patterning technology minimizes the usage of raw materials, diminishes the environmental impact, and enables a wide range of applications ranging from academia to industry. In this review, the recent developments in 3D porous LIG are comprehensively summarized. The mechanism of LIG formation is first introduced with a focus on laser‐material interactions and material transformations during laser irradiation. The effects of laser types, fabrication parameters, and lasing environment on LIG structures and properties are thoroughly discussed. The potentials of LIG for advanced applications including biosensors, physical sensors, supercapacitors, batteries, triboelectric nanogenerators, and so on are also highlighted. Finally, current challenges and future prospects of LIG research are discussed.
The increasing demand for wearable optoelectronics in biomedicine, prosthetics, and soft robotics calls for innovative and transformative technologies that permit facile fabrication of compact and flexible photodetectors with high performance. Herein, by developing a single‐step selective laser writing strategy that can finely tailor material properties through incident photon density control and lead to the formation of hierarchical hybrid nanocomposites, e.g., reduced graphene oxide (rGO)–zinc oxide (ZnO), a highly flexible and all rGO–ZnO hybrid‐based photodetector is successfully constructed. The device features 3D ultraporous hybrid films with high photoresponsivity as the active detection layer, and hybrid nanoflakes with superior electrical conductivity as interdigitated electrodes. Benefitting from enhanced photocarrier generation because of the ultraporous film morphology, efficient separation of electron–hole pairs at rGO–ZnO heterojunctions, and fast electron transport by highly conductive rGO nanosheets, the photodetector exhibits high, linear, and reproducible responsivities to a wide range of ultraviolet (UV) intensities. Furthermore, the excellent mechanical flexibility and robustness enable the photodetector to be conformally attached to skin, thus intimately monitoring the exposure dosage of human body to UV light for skin disease prevention. This study advances the fabrication of flexible optoelectronic devices with reduced complexity, facilitating the integration of wearable optoelectronics and epidermal systems.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.