Fast, simple, cost-efficient, eco-friendly, and design-flexible patterning of highquality graphene from abundant natural resources is of immense interest for the mass production of next-generation graphene-based green electronics. Most electronic components have been manufactured by repetitive photolithography processes involving a large number of masks, photoresists, and toxic etchants; resulting in slow, complex, expensive, less-flexible, and often corrosive electronics manufacturing processes to date. Here, a one-step formation and patterning of highly conductive graphene on natural woods and leaves by programmable irradiation of ultrafast high-photon-energy laser pulses in ambient air is presented. Direct photoconversion of woods and leaves into graphene is realized at a low temperature by intense ultrafast light pulses with controlled fluences. Green graphene electronic components of electrical interconnects, flexible temperature sensors, and energy-storing pseudocapacitors are fabricated from woods and leaves. This direct graphene synthesis is a breakthrough toward biocompatible, biodegradable, and ecofriendlily manufactured green electronics for the sustainable earth.

Human voice recognition systems (VRSs) are a prerequisite for voice-controlled human-machine interfaces (HMIs). In order to avoid interference from unexpected background noises, skin-attachable VRSs are proposed to directly detect physiological mechanoacoustic signals based on the vibrations of vocal cords. However, the sensitivity and response time of existing VRSs are bottlenecks for efficient HMIs. In addition, water-based contaminants in our daily lives, such as skin moisture and raindrops, normally result in performance degradation or even functional failure of VRSs. Herein, we present a skinattachable self-cleaning ultrasensitive and ultrafast acoustic sensor based on a reduced graphene oxide/polydimethylsiloxane composite film with bioinspired microcracks and hierarchical surface textures. Benefitting from the synergetic effect of the spider-slit-organ-like multiscale jagged microcracks and the lotus-leaf-like hierarchical structures, our superhydrophobic VRS exhibits an ultrahigh sensitivity (gauge factor, GF = 8699), an ultralow detection limit (ε = 0.000 064%), an ultrafast response/recovery behavior, an excellent device durability (>10 000 cycles), and reliable detection of acoustic vibrations over the audible frequency range (20−20 000 Hz) with high signal-to-noise ratios. These superb performances endow our skin-attachable VRS with anti-interference perception of human voices with high precision even in noisy environments, which will expedite the voice-controlled HMIs.

Noncontact electronic skin (e-skin), which possesses superior long-range and high-spatial-resolution sensory properties, is becoming indispensable in fulfilling the emulation of human sensation via prosthetics. Here, we present an advanced design and fabrication of all-graphene-based highly flexible noncontact e-skins by virtue of femtosecond laser direct writing (FsLDW). The photoreduced graphene oxide patterns function as the conductive electrodes, whereas the pristine graphene oxide thin film serves as the sensing layer. The as-fabricated e-skins exhibit high sensitivity, fast response-recovery behavior, good long-term stability, and excellent mechanical robustness. In-depth analysis reveals that the sensing mechanism is attributed to proton and ionic conductivity in the low and high humidity conditions, respectively. By taking the merits of the FsLDW, a 4 × 4 sensing matrix is facilely integrated in a single-step, eco-friendly, and green process. The light-weight and in-plane matrix shows high-spatial-resolution sensing capabilities over a long detection range in a noncontact mode. This study will open up an avenue to innovations in the noncontact e-skins and hold a promise for applications in wearable human-machine interfaces, robotics, and bioelectronics.

Flexible and stretchable strain sensors are in great demand for many applications like wearables and home health. This work reports a strain sensor fabricated using aerosol jet printing technology on a commercially available bandage to be used as a low-cost wearable. Laser light is explored to sinter the silver nanoparticle ink on low-temperature bandage substrate. The laser parameters, their effects on the microstructure of the film, and the resulting sensor performance are systematically investigated. The results showed that the sensor is stretchable, has good sensitivity, and stability for 700 cycles of repeated bending.

Laser‐induced graphene (LIG) is a newly emerging 3D porous material produced when irradiating a laser beam on certain carbon materials. LIG exhibits high porosity, excellent electrical conductivity, and good mechanical flexibility. Predesigned LIG patterns can be directly fabricated on diverse carbon materials with controllable microstructure, surface property, electrical conductivity, chemical composition, and heteroatom doping. This selective, low‐cost, chemical‐free, and maskless patterning technology minimizes the usage of raw materials, diminishes the environmental impact, and enables a wide range of applications ranging from academia to industry. In this review, the recent developments in 3D porous LIG are comprehensively summarized. The mechanism of LIG formation is first introduced with a focus on laser‐material interactions and material transformations during laser irradiation. The effects of laser types, fabrication parameters, and lasing environment on LIG structures and properties are thoroughly discussed. The potentials of LIG for advanced applications including biosensors, physical sensors, supercapacitors, batteries, triboelectric nanogenerators, and so on are also highlighted. Finally, current challenges and future prospects of LIG research are discussed.