Electroreduction of CO2 into useful fuels, especially if driven by renewable energy, represents a potentially 'clean' strategy for replacing fossil feedstocks and dealing with increasing CO2 emissions and their adverse effects on climate. The critical bottleneck lies in activating CO2 into the CO2(•-) radical anion or other intermediates that can be converted further, as the activation usually requires impractically high overpotentials. Recently, electrocatalysts based on oxide-derived metal nanostructures have been shown to enable CO2 reduction at low overpotentials. However, it remains unclear how the electrocatalytic activity of these metals is influenced by their native oxides, mainly because microstructural features such as interfaces and defects influence CO2 reduction activity yet are difficult to control. To evaluate the role of the two different catalytic sites, here we fabricate two kinds of four-atom-thick layers: pure cobalt metal, and co-existing domains of cobalt metal and cobalt oxide. Cobalt mainly produces formate (HCOO(-)) during CO2 electroreduction; we find that surface cobalt atoms of the atomically thin layers have higher intrinsic activity and selectivity towards formate production, at lower overpotentials, than do surface cobalt atoms on bulk samples. Partial oxidation of the atomic layers further increases their intrinsic activity, allowing us to realize stable current densities of about 10 milliamperes per square centimetre over 40 hours, with approximately 90 per cent formate selectivity at an overpotential of only 0.24 volts, which outperforms previously reported metal or metal oxide electrodes evaluated under comparable conditions. The correct morphology and oxidation state can thus transform a material from one considered nearly non-catalytic for the CO2 electroreduction reaction into an active catalyst. These findings point to new opportunities for manipulating and improving the CO2 electroreduction properties of metal systems, especially once the influence of both the atomic-scale structure and the presence of oxide are mechanistically better understood.

Exploring the interaction between two neighbouring monomers has great potential to significantly raise the performance and deepen the mechanistic understanding of heterogeneous catalysis. Herein, we demonstrate that the synergetic interaction between neighbouring Pt monomers on MoS greatly enhanced the CO hydrogenation catalytic activity and reduced the activation energy relative to isolated monomers. Neighbouring Pt monomers were achieved by increasing the Pt mass loading up to 7.5% while maintaining the atomic dispersion of Pt. Mechanistic studies reveal that neighbouring Pt monomers not only worked in synergy to vary the reaction barrier, but also underwent distinct reaction paths compared with isolated monomers. Isolated Pt monomers favour the conversion of CO into methanol without the formation of formic acid, whereas CO is hydrogenated stepwise into formic acid and methanol for neighbouring Pt monomers. The discovery of the synergetic interaction between neighbouring monomers may create a new path for manipulating catalytic properties.

Chemical vapor deposition (CVD) is an important method to synthesis grapheme on a substract. Recently, Cu becomes the most popular CVD substrate for graphene growth. Here, we combine electronic structure calculation, molecular dynamics simulation, and thermodynamics analysis to study the graphene growth process on Cu surface. As a fundamentally important but previously overlooked fact, we find that carbon atoms are thermodynamically unfavorable on Cu surface under typical experimental conditions. The active species for graphene growth should thus mainly be CH x instead of atomic carbon. Based on this new picture, the nucleation behavior can be understood, which explains many experimental observations and also provides us a guide to improve graphene sample quality.

Developing an active and stable metal single-atom catalyst (SAC) is challenging due to the high surface free energy of metal atoms. In this work, we report that tailoring of the 5d state of Pt1 single atoms on Co3O4 through strong electronic metal–support interactions (EMSIs) boosts the activity up to 68-fold higher than those on other supports in dehydrogenation of ammonia borane for room-temperature hydrogen generation. More importantly, this catalyst also exhibits excellent stability against sintering and leaching, in sharp contrast to the rapid deactivation observed on other Pt single-atom and nanoparticle catalysts. Detailed spectroscopic characterization and theoretical calculations revealed that the EMSI tailors the unoccupied 5d state of Pt1 single atoms, which modulates the adsorption of ammonia borane and facilities hydrogen desorption, thus leading to the high activity. Such extraordinary electronic promotion was further demonstrated on Pd1/Co3O4 and in hydrogenation reactions, providing a new promising way to design advanced SACs with high activity and stability.

Supported metal clusters containing only a few atoms are of great interest. Progress has been made in synthesis of metal single-atom catalysts. However, precise synthesis of metal dimers on high-surface area support remains a grand challenge. Here, we show that Pt2 dimers can be fabricated with a bottom–up approach on graphene using atomic layer deposition, through proper nucleation sites creation, Pt1 single-atom deposition and attaching a secondary Pt atom selectively on the preliminary one. Scanning transmission electron microscopy, x-ray absorption spectroscopy, and theoretical calculations suggest that the Pt2 dimers are likely in the oxidized form of Pt2Ox. In hydrolytic dehydrogenation of ammonia borane, Pt2 dimers exhibit a high specific rate of 2800 molH2 molPt −1 min−1 at room temperature, ~17- and 45-fold higher than graphene supported Pt single atoms and nanoparticles, respectively. These findings open an avenue to bottom–up fabrication of supported atomically precise ultrafine metal clusters for practical applications.

Our first principles calculations reveal that oxidative cut of graphene is realized by forming epoxy and then carbonyl pairs. Direct forming carbonyl pair to tear graphene up from an edge position is not favorable in energy. This atomic picture is valuable for developing effective graphene manipulation means. The proposed epoxy pairs may be related to some long puzzling experimental observations on graphene oxide.Due to its novel physical properties and great potential in various applications, graphene has attracted an intense research interest recently. i A big challenge in graphene research is the massive production of high quality samples. The existing physical approaches ii prohibit producing and processing graphene on large scales. In this context, the versatile chemistry of carbon may offer a promising alternative for cost-effective mass production of graphene, as demonstrated by its graphene-oxide (GO) synthesis route. Upon oxidation, graphite readily exfoliates as single sheets in water, forming GO. The π conjugation in graphene can then be largely restored by reducing GO. iii,iv Oxidation now becomes an important chemical means to manipulate graphitic materials.It has been observed that, during oxidation process, graphitic structures automatically break down into smaller parts. iv,v For electronics applications, it is very desirable to cut graphene with designed shape and size. Therefore, an atomistic understanding of the mechanism for such oxidative breakup of graphene sheets is especially valuable. Based on first-principles calculations, an unzipping mechanism has been proposed, vi where the epoxy groups formed during oxidation were suggested to have a preference of aligning in a line. The aligned epoxy groups then induce a rupture of the underlying C-C bonds (Figure 1a). However, it is still not clear how the graphene sheets can eventually break up, since even after the rupture of the C-C bonds the graphene sheet remains bridged by O atoms. Actually, a recent study shows that the mechanical strength of the graphene sheet is not strongly affected by the presence of epoxy chain and an epoxy line defect only weakens the fracture stress of the sheet by approximately 16%. vii This result indicates that, although the epoxy chain breaks the underlying C-C bonds, it does not really cause a breakup of the material by itself. The chemistry of the whole breakup process is still not clear.Previous experimental study on GO has suggested the existence of carbonyl groups, viii and a very recent two dimensional NMR experiment shows that the carbonyl groups are spatially separated from the majority sp 2 , C-OH, and epoxide carbons. ix This result indicates that carbonyl groups mainly distribute at the GO edge, and may thus be closely related to the oxidative break process. In this communication, based on density functional theory (DFT), we reveal how the oxygen attacks can break up atomic structure of graphene. Both the middle-site-initiated and the edge-site-initiated processes are studied, and the former based on i...

Graphene has attracted a lot of research interest owing to its exotic properties and a wide spectrum of potential applications. Chemical vapor deposition (CVD) from gaseous hydrocarbon sources has shown great promises for large-scale graphene growth. However, high growth temperature, typically 1000 °C, is required for such growth. Here we demonstrate a revised CVD route to grow graphene on Cu foils at low temperature, adopting solid and liquid hydrocarbon feedstocks. For solid PMMA and polystyrene precursors, centimeter-scale monolayer graphene films are synthesized at a growth temperature down to 400 °C. When benzene is used as the hydrocarbon source, monolayer graphene flakes with excellent quality are achieved at a growth temperature as low as 300 °C. The successful low-temperature growth can be qualitatively understood from the first principles calculations. Our work might pave a way to an undemanding route for economical and convenient graphene growth.

Chemical enhancement is an important mechanism in surface-enhanced Raman spectroscopy. It is found that mildly reduced graphene oxide (MR-GO) nanosheets can significantly increase the chemical enhancement of the main peaks by up to 1 order of magnitude for adsorbed Rhodamine B (RhB) molecules, in comparison with the mechanically exfoliated graphene. The observed enhancement factors can be as large as ∼10(3) and show clear dependence on the reduction time of graphene oxide, indicating that the chemical enhancement can be steadily controlled by specific chemical groups. With the help of X-ray photoelectron spectra, these chemical species are identified and the origin of the observed large chemical enhancement can thus be revealed. It is shown that the highly electronegative oxygen species, which can introduce a strong local electric field on the adsorbed molecules, are responsible for the large enhancement. In contrast, the local defects generated by the chemical reduction show no positive correlation with the enhancement. Most importantly, the dramatically enhanced Raman spectra of RhB molecules on MR-GO nanosheets reproduce all important spectral fingerprints of the molecule with a negligible frequency shift. Such a unique noninvasive feature, along with the other intrinsic advantages, such as low cost, light weight, easy availability, and flexibility, makes the MR-GO nanosheets very attractive to a variety of practical applications.