While 3D printing of rechargeable batteries has received immense interest in advancing the next generation of 3D energy storage devices, challenges with the 3D printing of electrolytes still remain. Additional processing steps such as solvent evaporation were required for earlier studies of electrolyte fabrication, which hindered the simultaneous production of electrode and electrolyte in an all-3D-printed battery. Here, a novel method is demonstrated to fabricate hybrid solid-state electrolytes using an elevated-temperature direct ink writing technique without any additional processing steps. The hybrid solid-state electrolyte consists of solid poly(vinylidene fluoride-hexafluoropropylene) matrices and a Li -conducting ionic-liquid electrolyte. The ink is modified by adding nanosized ceramic fillers to achieve the desired rheological properties. The ionic conductivity of the inks is 0.78  × 10 S cm . Interestingly, a continuous, thin, and dense layer is discovered to form between the porous electrolyte layer and the electrode, which effectively reduces the interfacial resistance of the solid-state battery. Compared to the traditional methods of solid-state battery assembly, the directly printed electrolyte helps to achieve higher capacities and a better rate performance. The direct fabrication of electrolyte from printable inks at an elevated temperature will shed new light on the design of all-3D-printed batteries for next-generation electronic devices.

This study examines the effect of environmental and experimental conditions, such as temperature and time, on the wettability properties of titania nanotube (TNT) surfaces fabricated by anodization. The fabricated TNTs are 60-130 nm inner diameter and 7-10 µm height. One-microliter water droplets were used to define the wettability of the TNT surfaces by measuring the contact angles. A digital image analysis algorithm was developed to obtain contact angles, contact radii and center heights of the droplets on the TNT surfaces. Bare titanium foil is inherently less hydrophilic with approximately 60°-80° contact angle. The as-anodized TNT surfaces are more hydrophilic and annealing further increases this hydrophilic property. Furthermore, it was found that the TNT surface became more hydrophobic when aged in air over a period of three months. It is believed that the surface wettability can be changed due to alkane contamination and organic contaminants in an ambient atmosphere. This work can provide guidelines to better specify the environmental conditions that changes surface properties of TNT surfaces and therefore affect their desirable function in specific applications such as orthopedic implants.

The mechanical compressive properties of individual thin-wall and thick-wall TiO(2) nanotubes were directly measured for the first time. Nanotubes with outside diameters of 75 and 110 nm and wall thicknesses of 5 and 15 nm, respectively, were axially compressed inside a 400 keV high-resolution transmission electron microscope (TEM) using a new fully integrated TEM-atomic force microscope (AFM) piezo-driven fixture for continuous recording of the force-displacement curves. Individual nanotubes were directly subjected to compressive loading. We found that the Young's modulus of titanium dioxide nanotubes depended on the diameter and wall thickness of the nanotube and is in the range of 23-44 GPa. The thin-wall nanotubes collapsed at approximately 1.0 to 1.2 microN during axial compression.

The synthesis of high entropy oxide (HEO) nanoparticles (NPs) possesses many challenges in terms of process complexity and cost, scalability, tailoring nanoparticle morphology, and rapid synthesis. Herein, we report the synthesis of novel single-phase solid solution (Mn, Fe, Ni, Cu, Zn)3(O)4 quinary HEO NPs produced by a flame spray pyrolysis route. The aberration-corrected scanning transmission electron microscopy (STEM) technique is utilized to investigate the spinel crystal structure of synthesized HEO NPs, and energy-dispersive X-ray spectroscopy analysis confirmed the high entropy configuration of five metal elements in their oxide form within a single HEO nanoparticle. Selected area electron diffraction, X-ray diffraction, and Raman spectroscopy analysis results are in accordance with STEM results, providing the key attributes of a spinel crystal structure of HEO NPs. X-ray photoelectron spectroscopy results provide the insightful understanding of chemical oxidation states of individual elements and their possible cation occupancy sites in the spinel-structured HEO NPs.

No abstract

No abstract

No abstract

No abstract