In the Nordic countries Finland, Norway and Sweden, the most common regeneration method is planting after clearcutting and, often, mechanical site preparation (MSP). The main focus of this study is to review quantitative effects that have been reported for the five main MSP methods in terms of survival and growth of manually planted coniferous seedlings of Norway spruce ( (L.) Karst.), Scots pine ( L.) and lodgepole pine ( var. Engelm.) in clearcuts in these three countries. Meta analyses are used to compare the effects of MSP methods to control areas where there was no MSP and identify any relationships with temperature sum and number of years after planting. In addition, the area of disturbed soil surface and the emergence of naturally regenerated seedlings are evaluated. The MSP methods considered are patch scarification, disc trenching, mounding, soil inversion and ploughing. Studies performed at sites with predominately mineral soils (with an organic topsoil no thicker than 0.30 m), in boreal, nemo-boreal and nemoral vegetation zones in the three Fenno-Scandinavian countries are included in the review. Data from 26 experimental and five survey studies in total were compiled and evaluated. The results show that survival rates of planted conifers at sites where seedlings are not strongly affected by pine weevil ( L.) are generally 80–90% after MSP, and 15–20 percent units higher than after planting in non-prepared sites. The experimental data indicated that soil inversion and potentially ploughing (few studies) give marginally greater rates than the other methods in this respect. The effects of MSP on survival seem to be independent of the temperature sum. Below 800 degree days, however, the reported survival rates are more variable. MSP generally results in trees 10–25% taller 10–15 years after planting compared to no MSP. The strength of the growth effect appears to be inversely related to the temperature sum. The compiled data may assist in the design, evaluation and comparison of possible regeneration chains, i.e. analyses of the efficiency and cost-effectiveness of multiple combinations of reforestation measures.Picea abiesPinus sylvestrisPinus contortalatifoliaHylobius abietis

No abstract

No abstract

Economic result of forest regeneration chains, based either on spot mounding or on disc trenching and planting of Norway spruce (Picea abies [L.] Karst.) seedlings, were clarified and compared to each other. First, effects of soil preparation method on early development of Norway spruce stands were measured from field experiments. Second, the effects of soil preparation method on stand level management programs were modelled. The modelling was based on growth simulation and investment calculations. The soil preparation methods substantially affected early development of a stand. The density of the removed trees in early cleaning was 56% higher on the disc-trenched area compared to the spot-mounded area. The difference was especially high (120%), close by (<25 cm) the remained spruce seedlings. There was also a difference between the methods in the growth of crop spruces; at biological age of 8 years, the mean height of spruce was 110 cm on the spot-mounded area and 68 cm on the disc-trenched area. The differences led to divergent management programs between the areas. The disc-trenched area needed three young stand management operations whereas two was enough at the spot-mounded area. Although disc trenching is a less expensive method than spot mounding, the total management costs were higher in disc trenching than in spot mounding. Furthermore, incomes from the first commercial thinning were higher when regeneration based on spot mounding. At the interest rate of 3%, the investment in spot mounding had 329 € ha -1 higher net present value than the investment in disc trenching.

Soil preparation method affects outplanting success of Norway spruce container seedlings on till soils susceptible to frost heave Heiskanen J., Saksa T., Luoranen J. (2013). Soil preparation method affects outplanting success of Norway spruce container seedlings on till soils susceptible to frost heave. Silva Fennica vol. 47 no. 1 article id 893. 17 p. AbstractSoil preparation is a common practice that precedes outplanting of Norway spruce (Picea abies (L.) Karst.) in Finland as it enhances the survival and early growth of seedlings. Mounding in particular has become more common with Norway spruce planting in recent years. However, on fine-grained soils, the postplanting performance of seedlings has been poorer than on coarser soils even with mounding. This study examined the effects of different soil preparation treatments (spot and ditch mounding with varying mound height, inverting, unprepared control with or without a herbicide) on the postplanting performance of Norway spruce container seedlings on till soil susceptible to frost heave in two outplanting forest sites in central Finland. The results indicate higher soil temperature and lower soil water content especially in the highest mounds. Mounds, however, subsided gradually during the study years. Seedling mortality was higher and the proportion of vigorous seedlings was lower in the unprepared treatments, mainly due to increased pine weevil (Hylobius abietis L.) damage. Frost heave was present mainly on ditch mounded and inverted spots. Glyphosate herbicide treatment showed no benefit compared to the untreated control in two years. Consequently, seedling damage and conditions in the planting spots were reflected in seedling growth which was enhanced in the mounded spots. However, varying mound height or thickness of mineral capping showed no clear difference in seedling growth. The results therefore suggest that ditch or spot mounding should be used on frost heave susceptible forest soils to promote plantation establishment. Inverting or having no soil preparation with or without herbicide is not recommended.

No abstract

The purpose of the study was to analyse height growth, mortality, and ingrowth of individual small-sized trees in uneven-aged spruce-dominated stands. It was based on experimental data from 16 stands for a 15-year observation period including four measurements with a 5-year interval. In the data of this study, the heights of small-sized trees varied from 0.1 to about 9 m. Results showed that the growth of small trees was rather slow, particularly in the smallest size classes. With average growth rates it would take about 60 years for a freshly emerged spruce germinant to achieve 1.3 m in height. The stand density, site quality and selection cuttings affected the growth of small-sized spruces. Average five-year mortality rates for spruce, birch and pine were 17.0%, 40.9% and 33.9%, respectively. Annual ingrowth rates with the threshold height of 1.3 m for the three species were on average 30.4, 2.8 and less than 0.1 trees per hectare, respectively. Even if, a selection cutting of modest intensity (25% of basal area removed on average) seemed to have accelerated the growth of small spruces, it is recommended that more intensive harvestings be applied to enhance the survival and growth of small spruces. It is also concluded that shade intolerant species like birch and pine do not seem to be capable of developing into viable undergrowth in spruce selection stands with their current levels of stand density.

The study compares the applicability of different remote sensing data and digital change detection methods in detecting clear-cut areas in boreal forest. The methods selected for comparisons are simple and straightforward and thus applicable in practical forestry. The data tested were from Landsat satellite imagery and high-altitude panchromatic aerial orthophotographs. The change detection was based on image differencing. Three different approaches were tested: (1) pixel-by-pixel differencing and segmentation; (2) pixel block-level differencing and thresholding; and (3) presegmentation and unsupervised classification. The study shows that the methods and data sources used are accurate enough for operational detection of clear-cut areas.The study suggests that predelineated segments or pixel blocks should be used for image differencing to decrease the number of misinterpreted small areas. For the same reason the use of a digital forest mask is crucial in operational applications.