The development of flexible electronic skins with high sensitivities and multimodal sensing capabilities is of great interest for applications ranging from human healthcare monitoring to robotic skins to prosthetic limbs. Although piezoresistive composite elastomers have shown great promise in this area of research, typically poor sensitivities and low response times, as well as signal drifts with temperature, have prevented further development of these materials in electronic skin applications. Here, we introduce and demonstrate a design of flexible electronic skins based on composite elastomer films that contain interlocked microdome arrays and display giant tunneling piezoresistance. Our design substantially increases the change in contact area upon loading and enables an extreme resistance-switching behavior (ROFF/RON of ∼10(5)). This translates into high sensitivity to pressure (-15.1 kPa(-1), ∼0.2 Pa minimum detection) and rapid response/relaxation times (∼0.04 s), with a minimal dependence on temperature variation. We show that our sensors can sensitively monitor human breathing flows and voice vibrations, highlighting their potential use in wearable human-health monitoring systems.
Stretchable electronic skins with multidirectional force-sensing capabilities are of great importance in robotics, prosthetics, and rehabilitation devices. Inspired by the interlocked microstructures found in epidermal-dermal ridges in human skin, piezoresistive interlocked microdome arrays are employed for stress-direction-sensitive, stretchable electronic skins. Here we show that these arrays possess highly sensitive detection capability of various mechanical stimuli including normal, shear, stretching, bending, and twisting forces. Furthermore, the unique geometry of interlocked microdome arrays enables the differentiation of various mechanical stimuli because the arrays exhibit different levels of deformation depending on the direction of applied forces, thus providing different sensory output patterns. In addition, we show that the electronic skins attached on human skin in the arm and wrist areas are able to distinguish various mechanical stimuli applied in different directions and can selectively monitor different intensities and directions of air flows and vibrations.
Bulk-type all-solid-state lithium batteries (ASLBs) are considered a promising candidate to outperform the conventional lithium-ion batteries. Unfortunately, the current technology level of ASLBs is in a stage of infancy in terms of cell-based (not electrode-material-based) energy densities and scalable fabrication. Here, we report on the first ever bendable and thin sulfide solid electrolyte films reinforced with a mechanically compliant poly(paraphenylene terephthalamide) nonwoven (NW) scaffold, which enables the fabrication of free-standing and stackable ASLBs with high energy density and high rate capabilities. The ASLB, using a thin (∼70 μm) NW-reinforced SE film, exhibits a 3-fold increase of the cell-energy-density compared to that of a conventional cell without the NW scaffold.
Electronic skins (e-skins) with high sensitivity to multidirectional mechanical stimuli are crucial for healthcare monitoring devices, robotics, and wearable sensors. In this study, we present piezoresistive e-skins with tunable force sensitivity and selectivity to multidirectional forces through the engineered microstructure geometries (i.e., dome, pyramid, and pillar). Depending on the microstructure geometry, distinct variations in contact area and localized stress distribution are observed under different mechanical forces (i.e., normal, shear, stretching, and bending), which critically affect the force sensitivity, selectivity, response/relaxation time, and mechanical stability of e-skins. Microdome structures present the best force sensitivities for normal, tensile, and bending stresses. In particular, microdome structures exhibit extremely high pressure sensitivities over broad pressure ranges (47,062 kPa −1 in the range of <1 kPa, 90,657 kPa −1 in the range of 1-10 kPa, and 30,214 kPa −1 in the range of 10-26 kPa). On the other hand, for shear stress, micropillar structures exhibit the highest sensitivity. As proof-of-concept applications in healthcare monitoring devices, we show that our e-skins can precisely monitor acoustic waves, breathing, and human artery/carotid pulse pressures. Unveiling the relationship between the microstructure geometry of e-skins and their sensing capability would provide a platform for future development of high-performance microstructured e-skins.
We utilize classical molecular dynamics simulations to investigate the intrinsic loss mechanisms of monolayer graphene nanoresonators undergoing flexural oscillations. We find that spurious edge modes of vibration, which arise not due to externally applied stresses but intrinsically due to the different vibrational properties of edge atoms, are the dominant intrinsic loss mechanism that reduces the Q-factors. We additionally find that while hydrogen passivation of the free edges is ineffective in reducing the spurious edge modes, fixing the free edges is critical to removing the spurious edge-induced vibrational states. Our atomistic simulations also show that the Q-factor degrades inversely proportional to temperature; furthermore, we also demonstrate that the intrinsic losses can be reduced significantly across a range of operating temperatures through the application of tensile mechanical strain.
Large-area graphene films are best synthesized via chemical vapour and/or solid deposition methods at elevated temperatures (~1,000 °C) on polycrystalline metal surfaces and later transferred onto other substrates for device applications. Here we report a new method for the synthesis of graphene films directly on sio 2 /si substrates, even plastics and glass at close to room temperature (25-160 °C). In contrast to other approaches, where graphene is deposited on top of a metal substrate, our method invokes diffusion of carbon through a diffusion couple made up of carbon-nickel/substrate to form graphene underneath the nickel film at the nickelsubstrate interface. The resulting graphene layers exhibit tunable structural and optoelectronic properties by nickel grain boundary engineering and show micrometre-sized grains on sio 2 surfaces and nanometre-sized grains on plastic and glass surfaces. The ability to synthesize graphene directly on non-conducting substrates at low temperatures opens up new possibilities for the fabrication of multiple nanoelectronic devices.
Stretchable conductors are essential components in next-generation deformable and wearable electronic devices. The ability of stretchable conductors to achieve sufficient electrical conductivity, however, remains limited under high strain, which is particularly detrimental for charge storage devices. In this study, we present stretchable conductors made from multiple layers of gradient assembled polyurethane (GAP) comprising gold nanoparticles capable of self-assembly under strain. Stratified layering affords control over the composite internal architecture at multiple scales, leading to metallic conductivity in both the lateral and transversal directions under strains of as high as 300%. The unique combination of the electrical and mechanical properties of GAP electrodes enables the development of a stretchable lithium-ion battery with a charge-discharge rate capability of 100 mAh g−1 at a current density of 0.5 A g−1 and remarkable cycle retention of 96% after 1000 cycles. The hierarchical GAP nanocomposites afford rapid fabrication of advanced charge storage devices.
We show that acetone-derived graphene coating can effectively enhance the corrosion efficiency of copper (Cu) in a seawater environment (0.5-0.6 M (∼3.0-3.5%) sodium chloride). By applying a drop of acetone (∼20 μl cm(-2)) on Cu surfaces, rapid thermal annealing allows the facile and rapid synthesis of graphene films on Cu surfaces with a monolayer coverage of almost close to ∼100%. Under optimal growth conditions, acetone-derived graphene is found to have a relatively high crystallinity, comparable to common graphene grown by chemical vapor deposition. The resulting graphene-coated Cu surface exhibits 37.5 times higher corrosion resistance as compared to that of mechanically polished Cu. Further, investigation on the role of graphene coating on Cu surfaces suggests that the outstanding corrosion inhibition efficiency (IE) of 97.4% is obtained by protecting the underlying Cu against the penetration of both dissolved oxygen and chlorine ions, thanks to the closely spaced atomic structure of the graphene sheets. The increase of graphene coating thickness results in the enhancement of the overall corrosion IE up to ∼99%, which can be attributed to the effective blocking of the ionic diffusion process via grain boundaries. Overall, our results suggest that the acetone-derived graphene film can effectively serve as a corrosion-inhibiting coating in the seawater level and that it may have a promising role to play for potential offshore coating.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.