With appropriate treatment, intraoperative sinus membrane perforations did not represent an elevated risk for implant loss, infectious complications or displacement of graft material in the investigated population.
This is an experimental study on human cadaver spines. The objective of this study is to compare the pullout forces between three screw augmentation methods and two different screw designs. Surgical interventions of patients with osteoporosis increase following the epidemiological development. Biomechanically the pedicle provides the strongest screw fixation in healthy bone, whereas in osteoporosis all areas of the vertebra are affected by the disease. This explains the high screw failure rates in those patients. Therefore PMMA augmentation of screws is often mandatory. This study involved investigation of the pullout forces of augmented transpedicular screws in five human lumbar spines (L1-L4). Each spine was treated with four different methods: non-augmented unperforated (solid) screw, perforated screw with vertebroplasty augmentation, solid screw with vertebroplasty augmentation and solid screw with balloon kyphoplasty augmentation. Screws were augmented with Polymethylmethacrylate (PMMA). The pullout forces were measured for each treatment with an Instron testing device. The bone mineral density was measured for each vertebra with Micro-CT. The statistical analysis was performed with a two-sided independent student t test. Forty screws (10 per group and level) were inserted. The vertebroplasty-augmented screws showed a significant higher pullout force (mean 918.5 N, P = 0.001) than control (mean 51 N), the balloon kyphoplasty group did not improve the pullout force significantly (mean 781 N, P > 0.05). However, leakage occurred in some cases treated with perforated screws. All spines showed osteoporosis on Micro-CT. Vertebroplasty-augmented screws, augmentation of perforated screws and balloon kyphoplasty augmented screws show higher pullout resistance than non-augmented screws. Significant higher pullout forces were only reached in the vertebroplasty augmented vertebra. The perforated screw design led to epidural leakage due to the position of the perforation in the screw. The position of the most proximal perforation is critical, depending on screw design and proper insertion depth. Nevertheless, using a properly designed perforated screw will facilitate augmentation and instrumentation in osteoporotic spines.
Selective laser melting (SLM), a method used in the nuclear, space, and racing industries, allows the creation of customized titanium alloy scaffolds with highly defined external shape and internal structure using rapid prototyping as supporting external structures within which bone tissue can grow. Human osteoblasts were cultured on SLM-produced Ti6Al4V mesh scaffolds to demonstrate biocompatibility using scanning electron microscopy (SEM), fluorescence microscopy after cell vitality staining, and common biocompatibility tests (lactate dihydrogenase (LDH), 3-(4,5-dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide (MTT), 5-bromo-2-deoxyuridine (BrdU), and water soluble tetrazolium (WST)). Cell occlusion of pores of different widths (0.45-1.2 mm) was evaluated. Scaffolds were tested for resistance to compressive force. SEM investigations showed osteoblasts with well-spread morphology and multiple contact points. Cell vitality staining and biocompatibility tests confirmed osteoblast vitality and proliferation on the scaffolds. Pore overgrowth increased during 6 weeks' culture at pore widths of 0.45 and 0.5 mm, and in the course of 3 weeks for pore widths of 0.55, 0.6, and 0.7 mm. No pore occlusion was observed on pores of width 0.9-1.2 mm. Porosity and maximum compressive load at failure increased and decreased with increasing pore width, respectively. In summary, the scaffolds are biocompatible, and pore width influences pore overgrowth, resistance to compressive force, and porosity.
PRF appears to be superior to collagen (Bio-Gide) as a scaffold for human periosteal cell proliferation. PRF membranes are suitable for in vitro cultivation of periosteal cells for bone tissue engineering.
Taken together, our results suggest considering periimplantitis and periodontitis as disease entities with shared as well as with distinct features, which should be reflected on the therapeutical as well as on the scientific level.
Within the limits of the study, we conclude that for bone defects larger than 4 mm in case of peri-implantitis, this single surgical intervention provided a reliable method to reduce bone defects.
Hydroxyapatite (HAP) and tricalcium phosphate (TCP) are two very common ceramic materials for bone replacement. However, in general HAP and TCP scaffolds are not tailored to the exact dimensions of the defect site and are mainly used as granules or beads. Some scaffolds are available as ordinary blocks, but cannot be customized for individual perfect fit. Using computer-assisted 3D printing, an emerging rapid prototyping technique, individual three-dimensional ceramic scaffolds can be built up from TCP or HAP powder layer by layer with subsequent sintering. These scaffolds have precise dimensions and highly defined and regular internal characteristics such as pore size. External shape and internal characteristics such as pore size can be fabricated using Computer Assisted Design (CAD) based on individual patient data. Thus, these scaffolds could be designed as perfect fit replacements to reconstruct the patient's skeleton. Before their use as bone replacement materials in vivo, in vitro testing of these scaffolds is necessary. In this study, the behavior of human osteoblasts on HAP and TCP scaffolds was investigated. The commonly used bone replacement material BioOss(R) served as control. Biocompatibility was assessed by scanning electron microscopy (SEM), fluorescence microscopy after staining for cell vitality with fluorescin diacetate (FDA) and propidium iodide (PI) and the MTT, LDH, and WST biocompatibility tests. Both versions were colonised by human osteoblasts, however more cells were seen on HAP scaffolds than TCP scaffolds. Cell vitality staining and MTT, LDH, and WST tests showed superior biocompatibility of HAP scaffolds to BioOss, while BioOss was more compatible than TCP. Further experiments are necessary to determine biocompatibility in vivo. Future modifications of 3D printed scaffolds offer advantageous features for Tissue Engineering. The integration of channels could allow for vascular and nerve ingrowth into the scaffold. Also the complex shapes of convex and concave articulating joint surfaces maybe realized with these rapid prototyping techniques.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.