One of the most promising methods against drug-resistant bacteria can be surface-modified materials with biocidal nanoparticles and nanocomposites. Herein, we present a nanocomposite with silver nanoparticles (Ag-NPs) on the surface of graphene oxide (GO) as a novel multifunctional antibacterial and antifungal material. Ultrasonic technologies have been used as an effective method of coating polyurethane foils. Toxicity on gram-negative bacteria (Escherichia coli), gram-positive bacteria (Staphylococcus aureus and Staphylococcus epidermidis), and pathogenic yeast (Candida albicans) was evaluated by analysis of cell morphology, assessment of cell viability using the PrestoBlue assay, analysis of cell membrane integrity using the lactate dehydrogenase assay, and reactive oxygen species production. Compared to Ag-NPs and GO, which have been widely used as antibacterial agents, our nanocomposite shows much higher antimicrobial efficiency toward bacteria and yeast cells.

No abstract

Introduction and objective Degradation of the extracellular matrix (ECM) changes the physicochemical properties and dysregulates ECM–cell interactions, leading to several pathological conditions, such as invasive cancer. Carbon nanofilm, as a biocompatible and easy to functionalize material, could be used to mimic ECM structures, changing cancer cell behavior to perform like normal cells. Methods Experiments were performed in vitro with HS-5 cells (as a control) and HepG2 and C3A cancer cells. An aqueous solution of fullerene C 60 was used to form a nanofilm. The morphological properties of cells cultivated on C 60 nanofilms were evaluated with light, confocal, electron and atomic force microscopy. The cell viability and proliferation were measured by XTT and BrdU assays. Immunoblotting and flow cytometry were used to evaluate the expression level of proliferating cell nuclear antigen and determine the number of cells in the G2/M phase. Results All cell lines were spread on C 60 nanofilms, showing a high affinity to the nanofilm surface. We found that C 60 nanofilm mimicked the niche/ECM of cells, was biocompatible and non-toxic, but the mechanical signal from C 60 nanofilm created an environment that affected the cell cycle and reduced cell proliferation. Conclusion The results indicate that C 60 nanofilms might be a suitable, substitute component for the niche of cancer cells. The incorporation of fullerene C 60 in the ECM/niche may be an alternative treatment for hepatocellular carcinoma.

No abstract

Medical implant use is associated with a risk of infection caused by bacteria on their surface. Implants with a surface that has both bone growth-promoting properties and antibacterial properties are of interest in orthopedics. In the current study, we fabricated a bioactive coating of hydroxyapatite nanoparticles on polyether ether ketone (PEEK) using the sonocoating method. The sonocoating method creates a layer by immersing the object in a suspension of nanoparticles in water and applying a high-power ultrasound. We show that the simple layer fabrication method results in a well-adhering layer with a thickness of 219 nm to 764 nm. Dropping cefuroxime sodium salt (Cef) antibiotic on the coated substrate creates a layer with a drug release effect and antibacterial activity against Staphylococcus aureus. We achieved a concentration of up to 1 mg of drug per cm2 of the coated substrate. In drug release tests, an initial burst was observed within 24 h, accompanied by a linear stable release effect. The drug-loaded implants exhibited sufficient activity against S. aureus for 24 and 168 h. Thus, the simple method we present here produces a biocompatible coating that can be soaked with antibiotics for antibacterial properties and can be used for a range of medical implants.

Controlling wetting of solids by liquids attracts attention because of its scientific and technological importance. In this paper, the wettability of a highly uniform porous poly(methyl methacrylate) film on a silicon substrate containing a high density of randomly distributed self-similar pores was gradually tuned by changing the shape of nanometric crownlike structures around the pores. Fine-tuning the topography of these thin films was performed by isothermal annealing. The equilibrium contact angle of a water droplet placed on the surface of the films could be varied from 72 to 102°. The contact angle changes were assumed to be a consequence of changes in surface topography in the nanoscale. A simple method of a quantitative description of the change of the topography of these films was developed. Critical dimensions of these films were determined in horizontal and vertical directions relative to the surface plane. The slope coefficient (SC) describing how sharp the structures are, is defined as the ratio between the critical dimensions: the root-mean-square roughness σ and the autocorrelation length ξ. For SC > 0.08, the contact angle increased proportionally to the value of SC, whereas for SC < 0.08, the contact angle proportionally decreased. At the highest SC values, the contact angles were 6−10% higher than those predicted for flat porous surfaces using the Cassie− Baxter equation. We suggest that this discrepancy is due to the capillary tension caused by the submicron-scale undulation of the triple line, which was found to be proportional to the height of the crownlike pore edges and the value of SC. The same effect is responsible for the linear dependence of the contact angle on the SC value.

No abstract

No abstract