Inorganic perovskite materials are possible candidates for conversion of solar energy to electrical energy due to their high absorption coefficient. Perovskite solar cells (PSCs) introduced a new type of device structure that has attention due to better efficiencies and interest in PSCs that has been increasing in recent years. Halide perovskite materials such as CsPbIBr2 show remarkable optical and structural performance with their better physical properties. Perovskite solar cells are a possible candidate to replace conventional silicon solar panels. In the present study, CsPbIBr2 perovskite materials’ thin films were prepared for light-absorbing application. Five thin films were deposited on the glass substrates by subsequent spin-coating of CsI and PbBr2 solutions, subsequently annealed at different temperature values (as-deposited, 100, 150, 200 and 250 °C) to get CsPbIBr2 thin films with a better crystal structure. Structural characterizations were made by using X-ray diffraction. CsPbIBr2 thin films were found to be polycrystalline in nature. With increasing annealing temperature, the crystallinity was improved, and the crystalline size was increased. Optical properties were studied by using transmission data, and by increasing annealing temperature, a small variation in optical band gap energy was observed in the range of 1.70–1.83 eV. The conductivity of CsPbIBr2 thin films was determined by a hot probe technique and was found to have little fluctuating response toward p-type conductivity, which may be due to intrinsic defects or presence of CsI phase, but a stable intrinsic nature was observed. The obtained physical properties of CsPbIBr2 thin films suggest them as a suitable candidate as a light-harvesting layer. These thin films could be an especially good partner with Si or other lower band gap energy materials in tandem solar cells (TSC). CsPbIBr2 material will harvest light having energy of ∼1.7 eV or higher, while a lower energy part of the solar spectrum will be absorbed in the partner part of the TSC.

No abstract

No abstract

No abstract

The development of cost-effective and nontoxic thin film materials is vital for fabrication of solar cells. We are presenting a combinatorial synthesis approach (CSA) for the deposition of chalcogenide Sn-Bi-S graded thin films by thermal evaporation. Post-deposition thermal annealing in the temperature range of 200-500°C in an argon atmosphere has been carried out for the Sn-Bi-S thin films. The effect of annealing treatment and initial composition on the structural properties of the Sn-Bi-S graded thin films was studied by using energy-dispersive X-ray spectroscopy, X-ray diffraction (XRD), and Raman spectroscopy. XRD measurements showed that the thin films were grown in polycrystalline structure. Different microstructural parameters such as crystallite size, dislocation density, and microstrain were estimated after postdeposition thermal treatment and found annealing temperature dependent. From the transmission spectra the estimated optical band gap energy values were found in the range 1.27-1.43 eV for the (Sn/Bi) molar ratio of 2.18-0.67 in a typical sample annealed at 400°C. Photoconductivity response was determined for incident light of wavelength 300-1100 nm and was observed to be annealing temperature and Sn/Bi molar ratio dependent. Photoconductivity was also noted to depend upon the Sn/Bi molar ratio with Sn-rich samples giving the strongest response. Sn-rich compositions also showed p-type conductivity over the temperature range of 350-400°C. These findings show that the CSA has potential for the screening of high-quality Sn-Bi-S thin films.

No abstract

Polycrystalline thin films of Cadmium Sulfide (CdS) have been extensively studied for application as a window layer in CdTe/CdS and CIGS/CdS thin film solar cells. Higher efficiency of solar cells is possible by a better conductivity of a window layer, which can be achieved by doping these films with suitable elements. CdS thin films were deposited on properly cleaned glass substrate by thermal evaporation technique under vacuum2×10-5mbar. Films were structurally characterized by using X-ray diffraction. The X-ray diffraction spectra showed that the thin films were polycrystalline in nature. Aluminum was doped chemically in as deposited and annealed thin films by immersing films in AlNO33.9H2O solutions respectively. Comparison between the effects of different doping ratios on the structural and optical properties of the films was investigated. Higher doping ratios have improved the electrical properties by decreasing the resistivity of the films and slightly changed the bandgap energy Eg. The grain size, strain, and dislocation density were calculated for as-deposited and annealed films.

Functionalised multi-walled carbon nanotubes (MWCNTs) are exclusively used in antibacterial activity due to their high aspect ratio and surface penetration characteristics. This study reports the synthesis of piperazine and dopamine functionalised MWCNTs to investigate antibacterial activity against strains like Staphylococcus aureus and Micrococcus luteus. MWCNTs were activated through acid oxidation and then refluxed at 75°C for 10 and 8 h in the presence of piperazine and dopamine, respectively. The functionalised MWCNTs were characterised by scanning electron microscopy, Fourier-transform infrared spectroscopy, X-ray diffraction and Raman spectroscopy. Moreover, functionalised MWCNTs were subjected to zone inhibition assay on agar plates. Results revealed the significant antibacterial activity against various bacteria up to 50%. Similarly, it was observed that the effect of different solvents, such as dimethyl formamide (DMF) and dimethyl sulfoxide (DMSO) was non-prevalent to the bacterial zone of inhibition. Such facile nano-modifications provide passage to nano-antibacterials for advanced studies.