New experiments using atmospheric pressure plasma have found large application in treatment of living cells or tissues, wound healing, cancerous cell apoptosis, blood coagulation on wounds, bone tissue modification, sterilization and decontamination. In this study an atmospheric pressure plasma jet generated using a cylindrical dielectric-barrier discharge was applied for treatment of burned wounds on Wistar rats' skin. The low temperature plasma jet works in helium and is driven by high voltage pulses. Oxygen and nitrogen based impurities are identified in the jet by emission spectroscopy. This paper analyses the natural epithelization of the rats' skin wounds and two methods of assisted epithelization, a classical one using polyurethane wound dressing and a new one using daily atmospheric pressure plasma treatment of wounds. Systemic and local medical data, such as haematological, biochemical and histological parameters, were monitored during entire period of study. Increased oxidative stress was observed for plasma treated wound. This result can be related to the presence in the plasma volume of active species, such as O and OH radicals. Both methods, wound dressing and plasma-assisted epithelization, provided positive medical results related to the recovery process of burned wounds. The dynamics of the skin regeneration process was modified: the epidermis re-epitelization was accelerated, while the recovery of superficial dermis was slowed down.
A two-dimensional (r, z) time-dependent fluid model was developed and used to describe a dc planar magnetron discharge with cylindrical symmetry. The transport description of the charged species uses the corresponding first three moments of the Boltzmann equation: continuity, momentum transfer and mean energy transfer (the last one only for electrons), coupled with the Poisson equation. An original method is proposed to treat the transport equations. Electron and ion momentum transport equations are reduced to the classical drift-diffusion expression for the fluxes since the presence of the magnetic field is introduced as an additional part in the electron flux, while for ions an effective electric field was considered. Thus, both continuity and mean energy transfer equations are solved in a classical manner. Numerical simulations were performed considering argon as a buffer gas, with a neutral pressure varying between 5 and 30 mTorr, for different voltages applied on the cathode. Results obtained for densities of the charged particle, fluxes and plasma potential are in good agreement with those obtained in previous studies.
The provision of a particle and power exhaust solution which is compatible with first-wall components and edge-plasma conditions is a key area of present-day fusion research and mandatory for a successful operation of ITER and DEMO. The work package plasma-facing components (WP PFC) within the European fusion programme complements with laboratory experiments, i.e. in linear plasma devices, electron and ion beam loading facilities, the studies performed in toroidally confined magnetic devices, such as JET, ASDEX Upgrade, WEST etc. The connection of both groups is done via common physics and engineering studies, including the qualification and specification of plasma-facing components, and by modelling codes that simulate edge-plasma conditions and the plasma-material interaction as well as the study of fundamental processes. WP PFC addresses these critical points in order to ensure reliable and efficient use of conventional, solid PFCs in ITER (Be and W) and DEMO (W and steel)
In this work, the surface treatment of poly(ethylene terephtalate) (PET) films in a low frequency (70 kHz) discharge in helium-oxygen mixtures is investigated. Optical emission spectroscopy and mass spectrometry are used to analyze the gas phase. Surface properties are analyzed via the X-ray photoelectron spectroscopy (XPS) technique and contact angle measurements. The treatment conditions are optimized in order to obtain a surface functionalization, which would show a reduced ageing effect. The stability of the treated surface via the crosslinking process seems to be closely correlated to the presence of the helium metastable species in the discharge. A very good stability with the ageing time is obtained for samples treated in gaseous mixtures that contain less than 5% O 2 , conditions for which the oxidized polymeric structure seems to be formed on a reinforced crosslinked layer. The very efficient loss of He excited species, for amounts of O 2 higher than a few percent, affects the surface crosslinking. For high quantities of oxygen introduced in the reactor (more than about 50%), a balance is established between the introduction of oxygenated groups and the ablation of the surface. In this case, the surface degradation has, as a consequence, the ageing effect.
The linear plasma generator Magnum-PSI was designed for the study of plasma-surface interactions under relevant conditions of fusion devices. A key factor for such studies is the knowledge of a set of parameters that characterize the plasma interacting with the solid surface. This paper reports on the electrical diagnosis of the plasma beam in Magnum-PSI using a multi-probe system consisting of 64 probes arranged in a 2D square matrix. Cross-section distributions of floating potential and ion current intensity were registered for a hydrogen plasma beam under various discharge currents (80-175 A) and magnetic field strengths (0.47-1.41 T in the middle of the coils). Probe measurements revealed a high level of flexibility of plasma beam parameters with respect to the operating conditions.
Films of poly(ethylene terephthalate) (PET) have been subjected to a low frequency (70 kHz) helium discharge, with a non-symmetrical configuration of electrodes, in order to study the treatment conditions for which the 'ageing' effect is slowed down. Treatments were made for different gas flow rates (40, 70 and 100 sccm) and different exposure times (1, 10 and 30 s). Emission spectroscopy and mass spectrometry were used to characterize the discharge plasma. The resulting modifications to the polymer surface were analysed via contact angle measurements and the XPS technique. It is pointed out that treatments on an He discharge induce both a functionalization and a cross linking of the uppermost layers of the polymer film. The residual oxygen, which partially originates within the polymer, induces surface oxidation. The cross-linked content critically depends on the residence time and concentration of implicated species. It seems that a change in the surface work function takes place as a result of a surface restructuring in the earliest stages of the reactions. This could involve an increase in the rate constant for the surface de-excitation of the helium metastables in the presence of the polymer. A contribution to the understanding of the competitive processes of cross linking and functionalization, as a function of the helium flow rate, is accomplished.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.