Abstract:Plasma-wall interaction (PWI) is important for the material choice in ITER and for the plasma scenarios compatible with material constraints. In this paper different aspects of the PWI are assessed in their importance for the initial wall materials choice: CFC for the strikepoint tiles, W in the divertor and baffle and Be on the first wall. Further material options are addressed for comparison, such as W divertor / Be first wall and all-W or all-C.One main parameter in this evaluation is the particle flux to the main vessel wall. One detailed plasma scenario exists for a Q=10 ITER discharge [ 1 ] which was taken as the basis of further erosion and tritium retention evaluations. As the assessment of steady state wall fluxes from a scaling of present fusion devices indicates that global wall fluxes may be a factor of 4±3 higher, this margin has been adopted as uncertainty of the scaling.With these wall and divertor fluxes, important PWI processes such as erosion and tritium accumulation have been evaluated:• It was found that the steady state erosion is no problem for the lifetime of plasma-facing divertor components. Be wall erosion may pose a problem in case of a concentration of the wall fluxes to small wall areas. ELM erosion may drastically limit the PFC lifetime if ELMs are not mitigated to energies below 0.5 MJ.• Dust generation is still a process which requires more attention. Conversion from gross or net erosion to dust and the assessment of dust on hot surfaces need to be investigated.• For low-Z materials the build-up of the tritium inventory is dominated by co-deposition with eroded wall atoms.• For W, where erosion and tritium co-deposition are small, the implantation, diffusion and bulk trapping constitute the dominant retention processes. First extrapolations with models based on laboratory data show small contributions to the inventory. For later ITER phases and the extrapolation to DEMO additional tritium trapping sites due to neutron-irradiation damage need to be taken into account.Finally the expected values for erosion and tritium retention are compared to the ITER administrative limits for the lifetime, dust and tritium inventory.

Abstract:Interactions between the plasma and the vessel walls constitute a major engineering problem for next step fusion devices, such as ITER, determining the choice of the plasma-facing materials. A prominent issue in this choice is the tritium inventory build-up in the vessel, which must be limited for safety reasons. The initial material selection, i.e. beryllium (Be) on the main vessel walls, tungsten (W) on the divertor upper baffle and dome, and carbon fibre composite (CFC) around the strike points on the divertor plates, results both from the attempt to reduce the tritium inventory and to optimise the lifetime of the plasma facing components (PFCs).In the framework of the EU Task Force on Plasma-Wall Interaction (PWI TF), the many physics aspects governing the tritium inventory are brought together. Together with supporting information from international experts represented by the ITPA SOL/DIV section, this paper describes the present status of knowledge of the in-vessel tritium inventory build-up. Firstly, the main results from present fusion devices in this field are briefly reviewed. Then, the processes involved are discussed: implantation, trapping and diffusion in plasma facing materials are considered as well as surface erosion and co-deposition of tritium with eroded material. The intermixing of the different materials and its influence on hydrogen retention and co-deposition is a major source of uncertainty on present estimates and is also addressed.Based on the previous considerations, estimates for the tritium inventory build up are given for the initial choice of ITER materials, as well as for alternative options. Present estimates indicate a build-up of the tritium inventory to the administrative limit within a few hundred nominal full power D:T discharges, co-deposition with carbon being the dominant process. Therefore, tritium removal methods are also an active area of research within the EU PWI TF, and are discussed. An integrated operational scheme to slow the rate of tritium accumulation is presented, which includes plasma operation as well as conditioning procedures. † Current address: Fusion for Energy,

This paper reports the successful installation of the JET ITER-like Wall and the realisation of its technical objectives. It also presents an overview of the planned experimental programme which has been optimised to exploit the new wall and other JET enhancement in 2011/12. IntroductionThe ITER reference materials [pitts] have been tested in isolation in tokamaks, plasma simulators, ion beams and high heat flux test beds. However, an integrated test demonstrating both acceptable tritium retention, predicted to be one to two orders of magnitude lower than for a carbon wall [roth], and an ability to operate a large high power tokamak within the limits set by these materials has not yet been carried out. The ITER-like Wall now installed in JET by remote handling comprises solid beryllium limiters and a combination of bulk W and Wcoated CFC divertor tiles.Work is also well advanced in defining the 2011/12 JET experimental programme and setting up the teams. A phased approach will be adopted which maximises the scientific output early in the programme on the basic materials and fuel retention questions whilst minimising the risk associated with operation in an all metal machine. However, re-establishing H-modes at similar power levels to those with the carbon walls is a priority for establishing a reference database. The JET upgrades also include an increase in neutral beam heating power, up to 35MW for 20s [ciric], this has led to a requirement that the most critical first wall Be and W components are monitored in real time by an appropriate imaging protection system [Alves, Jouve, Stephen]. In the main chamber, an array of thermocouples has been fitted to unambiguously monitor the bulk temperature of critical tiles. Before this upgrade, only a divertor system was available which proved essential for interpretation of IR data [Eich] and this will be even more the case with an all metal wall due to reflection and uncertain emissivity. Safe expansion of operating space will also be a priority. Experiments will have to be carefully managed if they have the potential to jeopardise interpretation of the long term samples which are planned to be removed in a 2012 intervention. Here the concern is that

Abstract:JET underwent a transformation from a full carbon-dominated tokamak to a full metallic device with the ITER-like wall combination for the activated phase with Beryllium main chamber and Tungsten divertor. The ITER-Like Wall (ILW) experiment at JET provides an ideal test bed for ITER and shall demonstrate as primary goals the plasma compatibility with metallic walls and the reduction in fuel retention. We report on a set of experiments ( = 2.0 , = 2.0 − 2.4 , = 0.2 − 0.4) in different confinement and plasma conditions with global gas balance analysis demonstrating a strong reduction of the long term retention rate by a factor ten with respect to carbon references. All experiments have been executed in a series of identical plasma discharges in order to achieve maximum plasma duration until the analysis limit of the active gas handling system has been reached. The composition analysis shows high purity of the recovered gas, typically 99% D. For typical L-mode discharges ( = 0.5 ), type III ( = 5.0 ), and type I ELMy H-mode plasmas ( = 12.0 ) a drop of the retention rate normalised to the operational time in divertor configuration has been measured from 1.27 × 10 has been obtained with the ILW. The observed reduction by one order of magnitude confirms the expected predictions concerning the plasma-facing material change in ITER and widens the operation without active cleaning in the DT phase in comparison to a full carbon device.

Demonstrating improved confinement of energetic ions is one of the key goals of the Wendelstein 7-X (W7-X) stellarator. In the past campaigns, measuring confined fast ions has proven to be challenging. Future deuterium campaigns would open up the option of using fusion-produced neutrons to indirectly observe confined fast ions. There are two neutron populations: 2.45 MeV neutrons from thermonuclear and beam-target fusion, and 14.1 MeV neutrons from DT reactions between tritium fusion products and bulk deuterium. The 14.1 MeV neutron signal can be measured using a scintillating fiber neutron detector, whereas the overall neutron rate is monitored by common radiation safety detectors, for instance fission chambers. The fusion rates are dependent on the slowing-down distribution of the deuterium and tritium ions, which in turn depend on the magnetic configuration via fast ion orbits. In this work, we investigate the effect of magnetic configuration on neutron production rates in W7-X. The neutral beam injection, beam and triton slowing-down distributions, and the fusion reactivity are simulated with the ASCOT suite of codes. The results indicate that the magnetic configuration has only a small effect on the production of 2.45 MeV neutrons from DD fusion and, particularly, on the 14.1 MeV neutron production rates. Despite triton losses of up to 50 %, the amount of 14.1 MeV neutrons produced might be sufficient for a time-resolved detection using a scintillating fiber detector, although only in high-performance discharges.