No abstract

Implant failure due to poor integration of the implant with the surrounding biomaterial is a common problem in various orthopedic and orthodontic surgeries. Implant fixation mostly depends upon the implant surface topography. Micron to nanosize circular-shaped groove architecture with adequate surface roughness can enhance the mechanical interlock and osseointegration of an implant with the host tissue and solve its poor fixation problem. Such groove architecture can be created on a titanium (Ti) alloy implant by laser peening treatment. Laser peening produces deep, residual compressive stresses in the surfaces of metal parts, delivering increased fatigue life and damage tolerance. The scientific novelty of this study is the controlled deposition of circular-shaped rough spot groove using laser peening technique and understanding the effect of the treatment techniques for improving the implant surface properties. The hypothesis of this study was that implant surface grooves created by controlled laser peen treatment can improve the mechanical and biological responses of the implant with the adjoining biomaterial. The objective of this study was to measure how the controlled laser-peened groove architecture on Ti influences its osteoblast cell functions and bonding strength with bone cement. This study determined the surface roughness and morphology of the peen-treated Ti. In addition, this study compared the osteoblast cell functions (adhesion, proliferation, and differentiation) between control and peen-treated Ti samples. Finally, this study measured the fracture strength between each kind of Ti samples and bone cement under static loading. This study found that laser peen treatment on Ti significantly changed the surface architecture of the Ti, which led to enhanced osteoblast cell adhesion and differentiation on Ti implants and fracture strength of Ti–bone cement interfaces compared with values of untreated Ti samples. Therefore, the laser peen treatment method has the potential to improve the biomechanical functions of Ti implants.

The objective of this study was to improve the biomechanical performance of titanium (Ti) using a biocompatible electrospun nanofiber matrix. The study is based on the hypothesis that coating a Ti surface with a nanofiber matrix (NFM) made of collagen (CG) and polycaprolactone (PCL) electrospun nanofibers could increase the mechanical fixation of Ti/bone by improving the surface and cytocompatibility properties of Ti. This study prepared Ti samples with and without CG-PCL NFM coatings. This study determined the effects of each group of Ti samples on the surface topography and cytocompatibility (osteoblast cell adhesion, proliferation, mineralization and protein adsorption) properties. This study also determined interface shear strength and bone volume fraction of each group of Ti samples with bone using a rabbit model. This study found that the CG-PCL NFM coating on Ti improved the surface roughness, osteoblast cell adhesion, proliferation, mineralization and protein adsorption properties of Ti. studies found that interface shear strength of CG-PCL NFM-coated Ti/bone samples was significantly higher compared to those values of control Ti/bone samples ( value < 0.05) due to an increase in the amount of growth of the connective tissue joining the Ti implant. Therefore, the developed CG-PCL NFM coating technique should further be investigated for its potential in clinical applications.

Titanium (Ti) alloys have been widely used in orthopedics and orthodontic surgeries as implants because of their beneficial chemical, mechanical, and biological properties. Improvement of these properties of a Ti alloy, Ti-6Al-4V Eli, is possible by the use of plasma nitriding treatment on the Ti alloy. The novelty of this study is the evaluation of a DC glow discharge nitrogen plasma treatment method on the surface, mechanical and biological properties of Ti alloy. Specifically, this study measured the chemical states, roughness, hardness, and biocompatibility of plasma nitride treated Ti-6Al-4V Eli as well as determined the effect of plasma treatment on the fracture strength between the Ti alloy and bone clement. This study hypothesized that DC glow discharge nitrogen plasma treatment may alter the surface chemical and mechanical states of the Ti alloy that may influence the fracture strength of implant/cement interfaces under static load. This study found that plasma nitride treatment on Ti alloy does not have effect on the roughness and biocompatibility (P value > 0.5), but significantly effect on the hardness and fracture strength of Ti-bone cement interfaces compared to those values of untreated Ti samples (P value < 0.5). Therefore, the DC glow discharge nitrogen plasma treated Ti alloy can potentially be used for orthopedic applications.

No abstract

No abstract