Semi-transparent perovskite solar cells are highly attractive for a wide range of applications, such as bifacial and tandem solar cells; however, the power conversion efficiency of semi-transparent devices still lags behind due to missing suitable transparent rear electrode or deposition process. Here we report a low-temperature process for efficient semi-transparent planar perovskite solar cells. A hybrid thermal evaporation–spin coating technique is developed to allow the introduction of PCBM in regular device configuration, which facilitates the growth of high-quality absorber, resulting in hysteresis-free devices. We employ high-mobility hydrogenated indium oxide as transparent rear electrode by room-temperature radio-frequency magnetron sputtering, yielding a semi-transparent solar cell with steady-state efficiency of 14.2% along with 72% average transmittance in the near-infrared region. With such semi-transparent devices, we show a substantial power enhancement when operating as bifacial solar cell, and in combination with low-bandgap copper indium gallium diselenide we further demonstrate 20.5% efficiency in four-terminal tandem configuration.

No abstract

The introduction of a KF post-deposition treatment (KF PDT) of Cu(In,Ga)Se 2 (CIGS) thin films has led to the achievement of several consecutive new world record efficiencies up to 21.7% for the CIGS solar cell technology. The beneficial effect of the KF PDT on the photovoltaic parameters was observed by several groups in spite of differing growth methods of the CIGS layer. For CIGS evaporated at lower temperature on alkali-free, flexible plastic substrates, a postdeposition treatment to add Na was already successfully applied. However with the introduction of additional KF under comparable conditions, distinctly different influences on the final absorber alkali content as well as surface properties are observed. In this work we discuss in more details the intrinsically different role of both alkali-treatments by combining several microstructural and compositional analysis methods. The ion exchange of Na by K in the bulk of the absorber is carefully analyzed, and further evidences for the formation of a K-containing layer on the CIGS surface with increased surface reactivity are given. These results shall serve as a basis for the further understanding of the effects of alkali PDT on CIGS and help identifying research needs to achieve even higher efficiencies.

Chalcopyrite solar cells achieve efficiencies above 23%. The latest improvements are due to post‐deposition treatments (PDT) with heavy alkalis. This study provides a comprehensive description of the effect of PDT on the chemical and electronic structure of surface and bulk of Cu(In,Ga)Se2. Chemical changes at the surface appear similar, independent of absorber or alkali. However, the effect on the surface electronic structure differs with absorber or type of treatment, although the improvement of the solar cell efficiency is the same. Thus, changes at the surface cannot be the only effect of the PDT treatment. The main effect of PDT with heavy alkalis concerns bulk recombination. The reduction in bulk recombination goes along with a reduced density of electronic tail states. Improvements in open‐circuit voltage appear together with reduced band bending at grain boundaries. Heavy alkalis accumulate at grain boundaries and are not detected in the grains. This behavior is understood by the energetics of the formation of single‐phase Cu‐alkali compounds. Thus, the efficiency improvement with heavy alkali PDT can be attributed to reduced band bending at grain boundaries, which reduces tail states and nonradiative recombination and is caused by accumulation of heavy alkalis at grain boundaries.

This review summarizes the current status of Cu(In,Ga)(S,Se) 2 (CIGS) thin film solar cell technology with a focus on recent advancements and emerging concepts intended for higher efficiency and novel applications. The recent developments and trends of research in laboratories and industrial achievements communicated within the last years are reviewed, and the major developments linked to alkali post deposition treatment and composition grading in CIGS, surface passivation, buffer, and transparent contact layers are emphasized. Encouraging results have been achieved for CIGS-based tandem solar cells and for improvement in low light device performance. Challenges of technology transfer of lab's record high efficiency cells to average industrial production are obvious from the reported efficiency values. One section is dedicated to development and opportunities offered by flexible and lightweight CIGS modules.

Flexible, lightweight Cu(In,Ga)Se2 (CIGS) solar cells grown on polymer substrates are a promising technology with fast growing market prospects. However, power conversion efficiencies of solar cells grown at low temperatures (≈450 °C) remain below the efficiencies of cells grown at high temperature on glass substrates. This contribution discusses the impact on cell efficiency of process improvements of low‐temperature CIGS deposition on flexible polyimide and glass substrates. Different strategies for incorporation of alkali elements into CIGS are evaluated based on a large number of depositions. Postdeposition treatment with heavy alkali (here RbF) enables a thickness reduction of the CdS buffer layer and increases the open‐circuit voltage. Na supply during 3rd stage CIGS deposition positively impacts the cell performance. Coevaporation of heavy alkali (e.g., RbF) during capping layer deposition mitigates the adverse shunting associated with high Cu contents, yielding highest efficiencies with near‐stoichiometric absorber compositions. Furthermore, optimization of the deposition sequence results in absorbers with a 1 µm wide notch region with nearly constant bandgap minimum. The improved processes result in a record cell efficiency of 20.8% for CIGS on flexible substrate.

A promising way to enhance the efficiency of CIGS solar cells is by combining them with perovskite solar cells in tandem devices. However, so far, such tandem devices had limited efficiency due to challenges in developing NIR-transparent perovskite top cells, which allow photons with energy below the perovskite band gap to be transmitted to the bottom cell. Here, a process for the fabrication of NIR-transparent perovskite solar cells is presented, which enables power conversion efficiencies up to 12.1% combined with an average sub-band gap transmission of 71% for photons with wavelength between 800 and 1000 nm. The combination of a NIR-transparent perovskite top cell with a CIGS bottom cell enabled a tandem device with 19.5% efficiency, which is the highest reported efficiency for a polycrystalline thin film tandem solar cell. Future developments of perovskite/CIGS tandem devices are discussed and prospects for devices with efficiency toward and above 27% are given.

Postdeposition treatments (PDTs) with sodium fluoride (NaF) and potassium fluoride (KF) were introduced as a way to improve the efficiency of Cu­(In,Ga)­Se2 (CIGS) based solar cells. Here, we apply postdeposition treatments with rubidium fluoride (RbF) to low-temperature coevaporated CIGS absorbers after a first PDT with NaF and compare the effects of the addition of Rb and K on the solar cell performance and material properties of the CIGS films. KF and RbF PDTs lead to similar improvements in the open-circuit voltage (V oc) and fill factor (FF), while allowing a reduction of the thickness of the cadmium sulfide (CdS) buffer layer without loss in electronic performance. KF and RbF PDTs lead to comparable modifications of the morphology and composition of the CIGS films. After the PDT, K and Rb accumulate in a nanopatterned copper-poor secondary phase at the CIGS surface, while also diffusing within the CIGS layer and strongly reducing the concentration of lighter alkali element sodium. These findings corroborate theoretical calculations published by another group, which predicted the segregation of potassium indium selenide (KInSe2) and rubidium indium selenide (RbInSe2) at CIGS surfaces under the used PDT conditions.