Conductometric semiconducting metal oxide gas sensors have been widely used and investigated in the detection of gases. Investigations have indicated that the gas sensing process is strongly related to surface reactions, so one of the important parameters of gas sensors, the sensitivity of the metal oxide based materials, will change with the factors influencing the surface reactions, such as chemical components, surface-modification and microstructures of sensing layers, temperature and humidity. In this brief review, attention will be focused on changes of sensitivity of conductometric semiconducting metal oxide gas sensors due to the five factors mentioned above.

Eutectic gallium–indium (EGaIn), a liquid metal with a melting point close to or below room temperature, has attracted extensive attention in recent years due to its excellent properties such as fluidity, high conductivity, thermal conductivity, stretchability, self‐healing capability, biocompatibility, and recyclability. These features of EGaIn can be adjusted by changing the experimental condition, and various composite materials with extended properties can be further obtained by mixing EGaIn with other materials. In this review, not only the are unique properties of EGaIn introduced, but also the working principles for the EGaIn‐based devices are illustrated and the developments of EGaIn‐related techniques are summarized. The applications of EGaIn in various fields, such as flexible electronics (sensors, antennas, electronic circuits), molecular electronics (molecular memory, opto‐electronic switches, or reconfigurable junctions), energy catalysis (heat management, motors, generators, batteries), biomedical science (drug delivery, tumor therapy, bioimaging and neural interfaces) are reviewed. Finally, a critical discussion of the main challenges for the development of EGaIn‐based techniques are discussed, and the potential applications in new fields are prospected.

A novel procedure is proposed as a method to characterize the chemical basis of selectivity for multivariate calibration models. This procedure involves submitting pure component spectra of both the target analyte and suspected interferences to the calibration model in question. The resulting model output is analyzed and interpreted in terms of the relative contribution of each component to the predicted analyte concentration. The utility of this method is illustrated by an analysis of calibration models for glucose, sucrose, and maltose. Near-infrared spectra are collected over the 5000-4000-cm(-)(1) spectral range for a set of ternary mixtures of these sugars. Partial least-squares (PLS) calibration models are generated for each component, and these models provide selective responses for the targeted analytes with standard errors of prediction ranging from 0.2 to 0.7 mM over the concentration range of 0.5-50 mM. The concept of the proposed pure component selectivity analysis is illustrated with these models. Results indicate that the net analyte signal is solely responsible for the selectivity of each individual model. Despite strong spectral overlap for these simple carbohydrates, calibration models based on the PLS algorithm provide sufficient selectivity to distinguish these commonly used sugars. The proposed procedure demonstrates conclusively that no component of the sucrose or maltose spectrum contributes to the selective measurement of glucose. Analogous conclusions are possible for the sucrose and maltose calibration models.

Understanding the relationship between multiphase structure and electromechanical property of thermoplastic dielectric elastomers is significantly important in the developments of high-performance and novel dielectric elastomers. In this work, we fabricated a series of aliphatic polyurethane elastomers (PUEs) based on hydroxyl-terminated butadiene-acrylonitrile copolymer (HTBN), hexamethylene diisocyanate (HDI), and various lengths of linear aliphatic diols and investigated effect of their microstructure and morphology on dielectric and electromechanical properties. The FTIR, WAXS, SAXS, and viscoelastic AFM results showed that the PUEs existed in crystalline phase, hard domain (HD) and soft domain (SD) phases composed HD-rich region and few HDs and SD composted SD-rich region by crystallization and microphase separation. Also, the crystal morphology and crystallinity of PUEs are strongly influenced by the length of chain extender due to the chain extender adopting various conformations by hydrogen bonding. The mechanical and electric fields induced responses of segment motions in PUEs at below room temperature were relative to the constrained SS motions from HD-rich and SD-rich regions. The electric field induced strain of PUEs was actuated by both Maxwell stress and electrostriction effect, of which contribution of electrostriction effect was above 64% in total actuation strain. In addition, we found that the effect of electrostriction on the actuation strain played an important role in improving the actuation strain of PUEs at lower electric field. Our results showed that the dielectric and electromechanical properties of PUEs can be adjusted by controlling the crystallization and microphase separation.