This study reports on the production of chitosan fibers and 3-D fiber meshes for the use as tissue engineering scaffolds. Both structures were produced by means of a wet spinning technique. Maximum strain at break and tensile strength of the developed fibers were found to be 8.5% and 204.9 MPa, respectively. After 14 d of immersion in simulated body fluid (SBF), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and inductively coupled plasma emission (ICP) spectroscopy analyses showed that a bioactive Ca-P layer was formed on the surface of the fibers, meaning that they exhibit a bioactive behavior. The samples showed around 120% max. swelling in physiological conditions. The pore sizes of 3-D chitosan fiber mesh scaffolds were observed to be in the range of 100-500 microm by SEM. The equilibrium-swelling ratio of the developed scaffolds was found to be around 170% (w/w) in NaCl solution at 37 degrees C. Besides that, the limit swelling strain was less than 30%, as obtained by mechanical spectroscopy measurements in the same conditions. The viscoelastic properties of the scaffolds were also evaluated by both creep and dynamic mechanical tests. By means of using short-term MEM extraction test, both types of structures (fibers and scaffolds) were found to be non-cytotoxic to fibroblasts. Furthermore, osteoblasts directly cultured over chitosan fiber mesh scaffolds presented good morphology and no inhibition of cell proliferation could be observed.Osteoblast-like cells proliferating over chitosan based fibers after 7 d of culture.

This work reports the synthesis and characterization of mesoporous silica nanoparticles (MSNs) functionalized with tridecafluorooctyltriethoxysilane (F13) and their in situ incorporation onto cotton textiles. The hybrid MSNs and the functional textiles were prepared by a one-pot co-condensation methodology between tetraethylorthosilicate (TEOS) and F13, with hexadecyltrimethylammonium chloride (CTAC) as the template and triethanolamine as the base. The influence of the F13 to TEOS molar ratio (1:10, 1:5 and 1:3) on the nanoparticle morphology, porosity, degree of functionalization, and hydro/oleophobic properties is discussed. The hybrid nanosilicas presented high colloidal stability and were spherical and monodispersed with average particle size of ∼45 nm. They also showed high surface areas, large pore volumes, and a wormhole-type mesoporous structure. The increase in the organosilane proportion during the co-condensation process led to a more radially branched wormhole-like mesoporosity, a decrease in the surface area, pore volume, and amount of surface silanol groups, and an enrichment of the surface with fluorocarbon moieties. These changes imparted hydrophobic and oleophobic properties to the materials, especially to that containing the highest F13 loading. Cotton textiles were coated with the F13-MSNs through an efficient and less time-consuming route. The combination between surface roughness and mesoporosity imparted by the MSNs, and the low surface energy provided by the organosilane resulted in superhydrophobic functional textiles. Moreover, the textile with the highest loading of fluorocarbon groups was superamphiphobic.

We have studied the influence of oxygen radio frequency glow discharge (RfGD) on the surface and bulk properties of poly(D,L-lactic acid) (PDLLA) and the effect of this surface modification on both protein adsorption and bone cell behavior. PDLLA films were characterized before and after plasma surface modification by water contact angle, surface energy, and adhesion tension of water as well as by scanning electron microscopy (SEM), X-ray electron spectroscopy (XPS), and Fourier transform infra-red (FTIR) spectroscopy. RfGD-films showed an increase in hydrophilicity and surface energy when compared with untreated films. Surface morphological changes were observed by SEM. Chemical analysis indicated significant differences in both atomic percentages and oxygen functional group. Protein adsorption was evaluated by combining solute depletion and spectroscopic techniques. Bovine serum albumin (BSA), fibronectin (FN), vitronectin (VN), and fetal bovine serum (FBS) were used in this study. RfGD-treated surfaces adsorbed more BSA and FN from single specie solutions than FBS that is a more complex, multi-specie solution. MG63 osteoblast-like cells and primary cultures of fetal rat calvarial (FRC) cells were used to assess both the effect of RfGD treatment and protein adsorption on cell attachment and proliferation. In the absence of preadsorbed proteins, cells could not distinguish between treated and untreated surfaces, with the exception of MG63 cells cultured for longer periods of time. In contrast, the adsorption of proteins increased the cells' preference for treated surfaces, thus indicating a crucial role for adsorbed proteins in mediating the response of osteogenic cells to the RfGD-treated PDLLA surface.

Production of aviation biofuels has been strongly encouraged by the volatility of oil prices and environmental concerns. Brazilian society, companies, and government are taking a step forward in the production of renewable jet fuel from biomass feedstocks largely available in the territory. This study evaluated the use of different feedstocks (sugar crops, oil crops, and lignocellulosic biomass) for co‐production of biojet fuel and higher value‐added products in a biorefinery platform. The co‐production of biofuels and biochemicals in a biorefinery context was demonstrated to be economically feasible. The main cost drivers of such a platform are feedstock biomass cost, selling price of the biochemicals, investment costs, and key process‐inherent parameters such as conversion yields, obtained fermentable sugars, or oil content in the feedstock. Sugarcane was the most promising feedstock for a biorefinery in the region of Minas Gerais, while soybean was the most promising feedstock for a biorefinery in the region of Rio Grande do Sul, despite its higher uncertainty. Succinic acid was the most promising chemical intermediate for biopolymers industry due to its relatively high market value, unique market opportunity as a substitute of conventional petrochemicals, and forecast for future growth. Ethanol‐to‐jet (ETJ) and hydro‐processed esters and fatty acids (HEFA) were the most attractive biojet fuel production routes in the present study. Scenarios for co‐production of biofuels and biochemicals in Brazil present large uncertainties and high financial risk, mainly due to the use of second‐generation feedstocks, and the introduction of new technologies and products. © 2016 Society of Chemical Industry and John Wiley & Sons, Ltd

The effect of oxygen-based radio frequency glow discharge (rfGD) on the surface of different starch-based biomaterials (SBB) and the influence of proteins adsorption on modulating bone-cells behavior was studied. Bovine serum albumin, fibronectin and vitronectin were used in single and complex protein systems. RfGD-treated surfaces showed to increase in hydrophilicity and surface energy when compared to non-modified SBB. Biodegradable polymeric blends of cornstarch with cellulose acetate (SCA; 50/50wt%), ethylene vinyl alcohol (SEVA-C; 50/50wt%) and polycaprolactone (SPCL; 30/70wt%) were studied. SCA and SCA reinforced with 10% hydroxyapatite (HA) showed the highest degree of modification as result of the rfGD treatment. Protein and control solutions were used to incubate with the characterized SBB and, following this, MG63 osteoblast-like osteosarcoma cells were seeded over the surfaces. Cell adhesion and proliferation onto SCA was found to be enhanced for non-treated surfaces and on SCA+10%HA no alteration was brought up by the plasma modification. Onto SCA surfaces, BSA, FN and VN single solutions improved cell adhesion, and this same effect was found upscaled for ternary systems. In addition, plasma treated SEVA-C directed an increase in both adhesion and proliferation comparing to non-treated surfaces. Even though adhesion onto treated and untreated SPCL was quite similar, plasma modification clearly promoted MG63 cells proliferation. Regarding MG63 cells morphology it was shown that onto SEVA-C surfaces the variation of cell shape was primarily defined by the protein system, while onto SPCL it was mainly affected by the plasma treatment.

Chitosan blends with synthetic biodegradable polymers have been proposed for various biomedical applications due to their versatile mechanical properties and easier processing. However, details regarding the main surface characteristics that may benefit from the blending of these two types of materials are still missing. Hence, this work aims at investigating the surface properties of chitosan-based blends, illustrating the way these properties determine the material-proteins interactions and ultimately the behavior of osteoblast-like cells. The surface characteristics of modified and nonmodified blends were assessed using complimentary techniques such as optical microscopy, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR-ATR), X-ray photoelectron spectroscopy (XPS), contact angle measurements and surface energy calculations. The adsorption of human serum albumin (HSA) and human plasma fibronectin (HFN) onto the different surfaces was quantified by association of an indirect method with a colorimetric assay. It was found that the presence of chitosan on the surface promoted the adsorption of proteins. Moreover, a preferential adsorption of albumin over fibronectin was registered. The in vitro biological performance of the studied materials was further investigated by a direct contact assay with an osteoblastic-like cell line (SaOs-2). A synergistic effect of the two components of the blend was observed. While the synthetic polyester promoted the adhesion of SaOs-2, the presence of chitosan significantly enhanced the osteoblastic activity of these cells. This work further confirmed the interest in designing polymeric blends with natural polymers as a successful strategy to enhance the biological performance of a biomaterial.

The use of bioabsorbable polymeric scaffolds is being investigated for use in bone tissue engineering applications, as their properties can be tailored to allow them to degrade and integrate at optimal rates as bone remodelling is completed. The main goal of this review is to highlight the ''intelligent'' properties exhibited by chitosan scaffolds and their use in the bone tissue engineering field. To complement the fast evolution of the bone tissue engineering field, it is important to propose the use of responsive scaffolds and take advantage of bioinspired materials and their properties as emerging technologies. There is a growing interest and need for new biomaterials, such as ''smart''/responsive materials with the capability to respond to changes in the in vivo environment. This review will provide an overview of strategies that can modulate bone tissue regeneration by using in situ-forming scaffolds.

Covalent grafting of biomolecules is a strategy to improve the biocompatibility and bioactivity of materials. However, it is critical to maintain the biological activity of the biomolecule upon its attachment to the surface. In the present study we compared the biological properties of chitosan, in which the surface was enriched with fibronectin (Fn), using two methodologies: chemical immobilization, using a water-soluble carbodiimide; and simple adsorption. X-ray photoelectron spectroscopy studies confirmed the successful immobilization of Fn onto modified membranes. SaOs-2 cells were seeded onto these surfaces to assess the biological consequences of such modifications. The presence of Fn stimulated cell adhesion on chitosan. It was found that after 7 days of culture in the presence of covalently attached Fn, the cells are confluent; significantly fewer cells were detected in unmodified film and in film with adsorbed Fn. This result is consistent with the fact that considerable desorption of Fn from chitosan takes place within 24 h in culture medium. This study showed that Fn may be easily covalently attached onto chitosan substrates, improving the biological performance of the material. The technique could find applications in tissue-engineering strategies, as the surface modification of chitosan-based substrates could be carried out in more complex geometries, such as in scaffolds or particles.