Metal-organic frameworks (MOFs) display a wide range of luminescent behaviors resulting from the multifaceted nature of their structure. In this critical review we discuss the origins of MOF luminosity, which include the linker, the coordinated metal ions, antenna effects, excimer and exciplex formation, and guest molecules. The literature describing these effects is comprehensively surveyed, including a categorization of each report according to the type of luminescence observed. Finally, we discuss potential applications of luminescent MOFs. This review will be of interest to researchers and synthetic chemists attempting to design luminescent MOFs, and those engaged in the extension of MOFs to applications such as chemical, biological, and radiation detection, medical imaging, and electro-optical devices (141 references).

Applications of metal-organic frameworks (MOFs) require close correlation between their structure and function. We describe the preparation and characterization of two zinc MOFs based on a flexible and emissive linker molecule, stilbene, which retains its luminescence within these solid materials. Reaction of trans-4,4'-stilbene dicarboxylic acid and zinc nitrate in N,N-dimethylformamide (DMF) yielded a dense 2-D network, 1, featuring zinc in both octahedral and tetrahedral coordination environments connected by trans-stilbene links. Similar reaction in N,N-diethylformamide (DEF) at higher temperatures resulted in a porous, 3-D framework structure, 2. This framework consists of two interpenetrating cubic lattices, each featuring basic zinc carboxylate vertices joined by trans-stilbene, analogous to the isoreticular MOF (IRMOF) series. We demonstrate that the optical properties of both 1 and 2 correlate with the local ligand environments observed in the crystal structures. Steady-state and time-resolved spectroscopic measurements reveal that the stilbene linkers in the dense structure 1 exhibit a small degree of interchromophore coupling. In contrast, the stilbenoid units in 2 display very little interaction in this low-density 3-D framework, with excitation and emission spectra characteristic of monomeric stilbenes, similar to the dicarboxylic acid in dilute solution. In both cases, the rigidity of the stilbene linker increases upon coordination to the inorganic units through inhibition of torsion about the central ethylene bond, resulting in luminescent crystals with increased emission lifetimes compared to solutions of trans-stilbene. The emission spectrum of 2 is found to depend on the nature of the incorporated solvent molecules, suggesting use of this or related materials in sensor applications.

Strong enhancement of the two-photon absorption of organic molecules near silver nanoparticle fractal clusters has been observed and has been exploited to yield composite materials with very strong two-photon absorption and two-photon-excited fluorescence properties. Measurements on cluster films coated with chromophoric polymer or with thiol-bound chromophores give spatially-averaged enhancements of 1000 and 20 000, respectively. Two-photon fluorescence microscopy studies show that the enhancements are spatially inhomogeneous, with peak-enhancement factors of g 10 000 (polymer/cluster) and g 160 000 (thiol chromophore/cluster), and excitation frequency dependent. These results are in accord with theoretical predictions of local-field effects due to strong localization of collective plasmon modes in fractal metal clusters, and demonstrate an approach to ultrasensitive two-photon processes.

Control over polymer sequence and architecture is crucial to both understanding structure–property relationships and designing functional materials. In pursuit of these goals, we developed a new synthetic approach that enables facile manipulation of the density and distribution of grafts in polymers via living ring-opening metathesis polymerization (ROMP). Discrete endo,exo-norbornenyl dialkylesters (dimethyl DME, diethyl DEE, di-n-butyl DBE) were strategically designed to copolymerize with a norbornene-functionalized polystyrene (PS), polylactide (PLA), or polydimethylsiloxane (PDMS) macromonomer mediated by the third-generation metathesis catalyst (G3). The small-molecule diesters act as diluents that increase the average distance between grafted side chains, generating polymers with variable grafting density. The grafting density (number of side chains/number of norbornene backbone repeats) could be straightforwardly controlled by the macromonomer/diluent feed ratio. To gain insight into the copolymer sequence and architecture, self-propagation and cross-propagation rate constants were determined according to a terminal copolymerization model. These kinetic analyses suggest that copolymerizing a macromonomer/diluent pair with evenly matched self-propagation rate constants favors randomly distributed side chains. As the disparity between macromonomer and diluent homopolymerization rates increases, the reactivity ratios depart from unity, leading to an increase in gradient tendency. To demonstrate the effectiveness of our method, an array of monodisperse polymers (PLA x -ran-DME 1‑x ) n bearing variable grafting densities (x = 1.0, 0.75, 0.5, 0.25) and total backbone degrees of polymerization (n = 167, 133, 100, 67, 33) were synthesized. The approach disclosed in this work therefore constitutes a powerful strategy for the synthesis of polymers spanning the linear-to-bottlebrush regimes with controlled grafting density and side chain distribution, molecular attributes that dictate micro- and macroscopic properties.

3D free‐standing and embedded metallic structures with a height of 100 μm (see Figure and also cover) have been microfabricated and characterized. Polymer nanocomposites containing metal nanoparticles, a metal salt, and an appropriate photoreducing dye are found to be efficient precursors for direct laser writing of continuous metal structures. The authors offer a versatile new approach to the 2D and 3D patterning of metals on different length scales.

No abstract

No abstract

The detection and identification of subatomic particles is an important scientific problem with implications for medical devices, radiography, biochemical analysis, particle physics, and astrophysics. In addition, the development of efficient detectors of neutrons generated by fissile material is a pressing need for nuclear nonproliferation efforts. A critical objective in the field of radiation detection is to obtain the physical insight necessary for rational design of scintillation materials. Many factors affect the quantum efficiency and timing of scintillator light output, including chemical composition, electronic structure, interchromophore interactions, crystal symmetry, and atomic density. None of the material types currently used in radiation detection, which include crystalline inorganic compounds such as LaBr 3 :Ce, organic compounds, and plastics, have the inherent synthetic versatility to exert systematic control over these factors. Therefore, it is likely that major advances in radiation detection will require the development of new materials outside the scope of traditional scintillators. Here, we propose that metal-organic frameworks (MOFs) could potentially offer the desired level of structural control, leading to an entirely new class of radiation detection materials.MOFs are crystalline materials consisting of metal clusters linked by coordinating organic groups. Yaghi, O'Keefe, and coworkers have shown that structures resulting from the selfassembly of specific metal ions and linkers can be predicted through an understanding of the geometric nets accessible to particular metal-linker combinations (''reticular chemistry''), [1][2][3]