No abstract

25The use of fused-filament 3D printing (FF 3DP) 30A final drug-loading of 0.29% w/w was achieved. Tablets of PVA/Fluorescein (10 mm 31 diameter) were printed using a 3D printer. It was found that changing the degree of

The aim of this study was to explore the potential of fused-deposition 3-dimensional printing (FDM 3DP) to produce modified-release drug loaded tablets. Two aminosalicylate isomers used in the treatment of inflammatory bowel disease (IBD), 5-aminosalicylic acid (5-ASA, mesalazine) and 4-aminosalicylic acid (4-ASA), were selected as model drugs. Commercially produced polyvinyl alcohol (PVA) filaments were loaded with the drugs in an ethanolic drug solution. A final drug-loading of 0.06% w/w and 0.25% w/w was achieved for the 5-ASA and 4-ASA strands, respectively. 10.5mm diameter tablets of both PVA/4-ASA and PVA/5-ASA were subsequently printed using an FDM 3D printer, and varying the weight and densities of the printed tablets was achieved by selecting the infill percentage in the printer software. The tablets were mechanically strong, and the FDM 3D printing was shown to be an effective process for the manufacture of the drug, 5-ASA. Significant thermal degradation of the active 4-ASA (50%) occurred during printing, however, indicating that the method may not be appropriate for drugs when printing at high temperatures exceeding those of the degradation point. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) of the formulated blends confirmed these findings while highlighting the potential of thermal analytical techniques to anticipate drug degradation issues in the 3D printing process. The results of the dissolution tests conducted in modified Hank's bicarbonate buffer showed that release profiles for both drugs were dependent on both the drug itself and on the infill percentage of the tablet. Our work here demonstrates the potential role of FDM 3DP as an efficient and low-cost alternative method of manufacturing individually tailored oral drug dosage, and also for production of modified-release formulations.

Citation: Goyanes A, Wang J, Buanz A, Martinez-Pacheco R, Telford R, Gaisford S and Basit AW (2015) 3D printing of medicines: Engineering novel oral devices with unique design and drug release characteristics. Molecular Pharmaceutics. 12(11): 3783-4174. Key wordsThree dimensional printing; controlled-release; fused deposition modelling; PVA; paracetamol; acetaminophen; caffeine; hot melt extrusion; Raman mapping 2 AbstractThree dimensional printing (3DP) was used to engineer novel oral drug delivery devices, with specialised design configurations loaded with multiple actives, with applications in personalised medicine. A filament extruder was used to obtain drug-loaded -paracetamol (acetaminophen) or caffeine -filaments of polyvinyl alcohol with characteristics suitable for use in fused-deposition modelling 3D printing. A multi-nozzle 3D printer enabled fabrication of capsule-shaped solid devices, containing paracetamol and caffeine, with different internal structures. The design configurations included a multilayer device, with each layer containing drug, whose identity was different from the drug in the adjacent layers; and a two-compartment device comprising a caplet embedded within a larger caplet (DuoCaplet), with each compartment containing a different drug. Raman spectroscopy was used to collect 2-dimensional hyper spectral arrays across the entire surface of the devices. Processing of the arrays using direct classical least squares component matching to produce false colour representations of distribution of the drugs showed clearly the areas that contain paracetamol and caffeine, and that there is a definitive separation between the drug layers.Drug release tests in biorelevant media showed unique drug release profiles dependent on the macrostructure of the devices. In the case of the multilayer devices, release of both drugs was simultaneous and independent of drug solubility. With the DuoCaplet design it was possible to engineer either rapid drug release or delayed release by selecting the site of incorporation of the drug in the device, and the lag-time for release from the internal compartment was dependent on the characteristics of the external layer. The study confirms the potential of 3D printing to fabricate multiple-drug containing devices with specialized design configurations and unique drug release characteristics, which would not otherwise be possible using conventional manufacturing methods.3

The aim of this work was to explore the feasibility of using fused deposition modelling (FDM) 3D printing (3DP) technology with hot melt extrusion (HME) and fluid bed coating to fabricate modified-release budesonide dosage forms. Budesonide was sucessfully loaded into polyvinyl alcohol filaments using HME. The filaments were engineered into capsule-shaped tablets (caplets) containing 9mg budesonide using a FDM 3D printer; the caplets were then overcoated with a layer of enteric polymer. The final printed formulation was tested in a dynamic dissolution bicarbonate buffer system, and two commercial budesonide products, Cortiment® (Uceris®) and Entocort®, were also investigated for comparison. Budesonide release from the Entocort® formulation was rapid in conditions of the upper small intestine while release from the Cortiment® product was more delayed and very slow. In contrast, the new 3D printed caplet formulation started to release in the mid-small intestine but release then continued in a sustained manner throughout the distal intestine and colon. This work has demonstrated the potential of combining FDM 3DP with established pharmaceutical processes, including HME and film coating, to fabricate modified release oral dosage forms.

TIJ printing offers a rapid method for extemporaneous preparation of personalized-dose medicines.

The generation of multi-functional drug delivery systems, namely solid dosage forms loaded with nano-sized carriers, remains little explored and is still a challenge for formulators. For the first time, the coupling of two important technologies, 3D printing and nanotechnology, to produce innovative solid dosage forms containing drug-loaded nanocapsules was evaluated here. Drug delivery devices were prepared by fused deposition modelling (FDM) from poly(ε-caprolactone) (PCL) and Eudragit RL100 (ERL) filaments with or without a channelling agent (mannitol). They were soaked in deflazacort-loaded nanocapsules (particle size: 138nm) to produce 3D printed tablets (printlets) loaded with them, as observed by SEM. Drug loading was improved by the presence of the channelling agent and a linear correlation was obtained between the soaking time and the drug loading (r=0.9739). Moreover, drug release profiles were dependent on the polymeric material of tablets and the presence of the channelling agent. In particular, tablets prepared with a partially hollow core (50% infill) had a higher drug loading (0.27% w/w) and faster drug release rate. This study represents an original approach to convert nanocapsules suspensions into solid dosage forms as well as an efficient 3D printing method to produce novel drug delivery systems, as personalised nanomedicines.

The aim of this work was to compare and contrast the mechanical properties and physical stabilities of oral films prepared with either thermal ink-jet printing (TIJP) or solvent casting (SC). Clonidine hydrochloride was selected as a model drug because of its low therapeutic dose and films were prepared using cellulose polymers. Mechanical testing showed that the printed films had Young's moduli and tensile strength values similar to the free film, while casted films were significantly more brittle. The drug also appeared to crystallize out of casted films during stress testing whereas printed films remained unchanged. The dissolution behavior of printed and cast films were similar, because of the rapid disintegration of the polymer. The conclusion is that printing resulted in a better film than casting because the drug resided on the film, rather than in the film where it could exert a plasticizing effect.