One-step fabrication of transparent three-dimensional (3D) microfluidic to millifluidic devices was demonstrated using a commercial 3D printer costing $2300 with 500 mL of clear resin for $138. It employs dynamic mask projection stereolithography, allowing fast concept-to-chip time. The fully automated system allows fabrication of models of up to 43 mm × 27 mm × 180 mm (x × y × z) at printing speeds of 20 mm/h in height regardless of the design complexity. The minimal cross sectional area of 250 μm was achieved for monolithic microchannels and 200 μm for positive structures (templates for soft lithography). The colorless resin's good light transmittance (>60% transmission at wavelengths of >430 nm) allows for on-chip optical detection, while the electrically insulating material allows electrophoretic separations. To demonstrate its applicability in microfluidics, the printer was used for the fabrication of a micromixer, a gradient generator, a droplet extractor, and a device for isotachophoresis. The mixing and gradient formation units were incorporated into a device for analysis of nitrate in tap water with standard addition as a single run and multiple depth detection cells to provide an extended linear range.

One of the most cited limitations of capillary (and microchip) electrophoresis is the poor sensitivity. This review continues to update this series of biannual reviews, first published in Electrophoresis in 2007, on developments in the field of on-line/in-line concentration methods, covering the period July 2012-July 2014. It includes developments in the field of stacking, covering all methods from field-amplified sample stacking and large-volume sample stacking, through to ITP, dynamic pH junction, and sweeping. Attention is also given to on-line or in-line extraction methods that have been used for electrophoresis.

CE has been alive for over two decades now, yet its sensitivity is still regarded as being inferior to that of more traditional methods of separation such as HPLC. As such, it is unsurprising that overcoming this issue still generates much scientific interest. This review continues to update this series of reviews, first published in Electrophoresis in 2007, with updates published in 2009 and 2011 and covers material published through to June 2012. It includes developments in the field of stacking, covering all methods from field amplified sample stacking and large volume sample stacking, through to isotachophoresis, dynamic pH junction and sweeping. Attention is also given to online or inline extraction methods that have been used for electrophoresis.

One of the most cited limitations of capillary and microchip electrophoresis is the poor sensitivity. This review continues to update this series of biannual reviews, first published in Electrophoresis in 2007, on developments in the field of online/in‐line concentration methods in capillaries and microchips, covering the period July 2016–June 2018. It includes developments in the field of stacking, covering all methods from field‐amplified sample stacking and large‐volume sample stacking, through to isotachophoresis, dynamic pH junction, and sweeping. Attention is also given to online or in‐line extraction methods that have been used for electrophoresis.

One of the most cited limitations of capillary (and microchip) electrophoresis is the poor sensitivity. This review continues to update this series of biennial reviews, first published in Electrophoresis in 2007, on developments in the field of on-line/in-line concentration methods in capillaries and microchips, covering the period July 2014-June 2016. It includes developments in the field of stacking, covering all methods from field amplified sample stacking and large volume sample stacking, through to isotachophoresis, dynamic pH junction, and sweeping. Attention is also given to on-line or in-line extraction methods that have been used for electrophoresis.

Lubricin is a glycoprotein found in articular joints which has long been recognized as being an important biological boundary lubricant molecule and, more recently, an impressive antiadhesive that readily self-assembles into a well ordered, polymer brush layer on virtually any substrate. The lubricin molecule possesses an overabundance of anionic charge, a property that is atypical among antiadhesive molecules, that enables its use as a coating for applications involving electrokinetic processes such as electrophoresis and electroosmosis. Coating the surfaces of silica and polymeric microfluidic devices with self-assembled lubricin coatings affords a unique combination of excellent fouling resistance and high charge density that enables notoriously "sticky" biomolecules such as proteins to be used and controlled electrokinetically in the device without complications arising from nonspecific adsorption. Using capillary electrophoresis, we characterized the stability, uniformity, and electrokinetic properties of lubricin coatings applied to silica and PTFE capillaries over a range of run buffer pHs and when exposed to concentrated solutions of protein. In addition, we demonstrate the effectiveness of lubricin as a coating to minimize nonspecific protein adsorption in an electrokinetically controlled polydimethylsiloxane/silica microfluidic device.

Control of the dielectric breakdown of PDMS was achieved by limiting the current during the breakdown process. This enabled tuning of the nanochannel pore size and hence their permeability for molecules of different molecular weights. This method enabled the analysis of the drug quinine from whole blood in 3 min using a simple, disposable microfluidic device.

No abstract