No abstract

Control of the dielectric breakdown of PDMS was achieved by limiting the current during the breakdown process. This enabled tuning of the nanochannel pore size and hence their permeability for molecules of different molecular weights. This method enabled the analysis of the drug quinine from whole blood in 3 min using a simple, disposable microfluidic device.

No abstract

A dual-channel sequential injection microchip capillary electrophoresis system with pressure-driven injection is demonstrated for simultaneous separations of anions and cations from a single sample. The poly(methyl methacrylate) (PMMA) microchips feature integral in-plane contactless conductivity detection electrodes. A novel, hydrodynamic "split-injection" method utilizes background electrolyte (BGE) sheathing to gate the sample flows, while control over the injection volume is achieved by balancing hydrodynamic resistances using external hydrodynamic resistors. Injection is realized by a unique flow-through interface, allowing for automated, continuous sampling for sequential injection analysis by microchip electrophoresis. The developed system was very robust, with individual microchips used for up to 2000 analyses with lifetimes limited by irreversible blockages of the microchannels. The unique dual-channel geometry was demonstrated by the simultaneous separation of three cations and three anions in individual microchannels in under 40 s with limits of detection (LODs) ranging from 1.5 to 24 μM. From a series of 100 sequential injections the %RSDs were determined for every fifth run, resulting in %RSDs for migration times that ranged from 0.3 to 0.7 (n = 20) and 2.3 to 4.5 for peak area (n = 20). This system offers low LODs and a high degree of reproducibility and robustness while the hydrodynamic injection eliminates electrokinetic bias during injection, making it attractive for a wide range of rapid, sensitive, and quantitative online analytical applications.

A comprehensively coupled online two-dimensional ion chromatography-capillary electrophoresis (IC × CE) system for quantitative analysis of inorganic anions and organic acids in water is introduced. The system employs an in-house built sequential injection-capillary electrophoresis instrument and a nonfocusing modulation interface comprising a tee-piece and a six-port two-position injection valve that allows comprehensive sampling of the IC effluent. High field strength (+2 kV/cm) enables rapid second-dimension separations in which each peak eluted from the first-dimension separation column is analyzed at least three times in the second dimension. The IC × CE approach has been successfully used to resolve a suite of haloacetic acids, dalapon, and common inorganic anions. Two-dimensional peak capacity for IC × CE was 498 with a peak production rate of 9 peaks/min. Linear calibration curves were obtained for all analytes from 5 to 225 ng/mL (except dibromoacetic acid (10-225 ng/mL) and tribromoacetic acid (25-225 ng/mL)). The developed approach was used to analyze a spiked tap water sample, with good measured recoveries (69-119%).

A simple method for producing PMMA electrophoresis microchips with in-plane electrodes for capacitively coupled contactless conductivity detection is presented. One PMMA plate (channel plate) is embossed with the microfluidic and electrode channels and lamination bonded to a blank PMMA cover plate of equal dimensions. To incorporate the electrodes, the bonded chip is heated to 80 °C, above the melting point of the alloy (≈ 70 °C) and below the glass transition temperature of the PMMA (≈ 105 °C), and the molten alloy drawn into the electrode channels with a syringe before being allowed to cool and harden. A 0.5 mm diameter stainless steel pin is then inserted into the alloy filled reservoirs of the electrode channels to provide external connection to the capacitively coupled contactless conductivity detection detector electronics. This advance provides for a quick and simple manufacturing process and negates the need for integrating electrodes using costly and time-consuming thin film deposition methods. No additional detector cell mounting structures were required and connection to the external signal processing electronics was achieved by simply slipping commercially available shielded adaptors over the pins. With a non-optimised electrode arrangement consisting of a 1 mm detector gap and 100 μm insulating distance, rapid separations of ammonium, sodium and lithium (<22 s) yielded LODs of approximately 1.5-3.5 ppm.

No abstract