We present experimental results on photonic crystal/photonic wire micro-cavity structures that demonstrate further enhancement of the quality-factor (Q-factor)--up to approximately 149,000--in the fibre telecommunications wavelength range. The Q-values and the useful transmission levels achieved are due, in particular, to the combination of both tapering within and outside the micro-cavity, with carefully designed hole diameters and non-periodic hole placement within the tapered section. Our 2D Finite Difference Time Domain (FDTD) simulation approach shows good agreement with the experimental results.

Abstract-We present the design, fabrication, and characterization of a microcavity that exhibits simultaneously high transmission and large resonance quality-factor (Q-factor). This microcavity is formed by a single-row photonic crystal (PhC) embedded in a 500-nm-wide photonic wire waveguide-and is based on silicon-on-insulator. A normalized transmission of 85%, together with a Q-factor of 18 500, have been achieved experimentally through the use of carefully designed tapering on both sides of each of the hole-type PhC mirrors that form the microcavity. We have also demonstrated reasonably accurate control of the cavity resonance frequency. Simulation of the device using a three-dimensional finite-difference time-domain approach shows good agreement with the experimental results.Index Terms-Microcavities, photonic crystal (PhC), photonic wires (PhWs), quality-factor ( -factor), silicon-on-insulator (SOI).

We report on experimental demonstration of all-optical switching in a silicon-on-insulator photonic wire nanocavity operating at telecom wavelengths. The switching is performed with a control pulse energy as low as approximately 0.1 pJ on a cavity device that presents very high signal transmission, an ultra-high quality-factor, almost diffraction-limited modal volume and a footprint of only 5 microm(2). High-speed modulation of the cavity mode is achieved by means of optical injection of free carriers using a nanosecond pulsed laser. Experimental results are interpreted by means of finite-difference time-domain simulations. The possibility of using this device as a logic gate is also demonstrated.

The interferogram of a high index phase mask of 200 nm period under normal incidence of a collimated beam at 244 nm wavelength with substantially suppressed zeroth order produces a 100 nm period grating in a resist film under immersion. The paper describes the phase mask design, its fabrication, the effect of electron-beam lithographic stitching errors and optical assessment of the fabricated sub-cutoff grating.

Background: The production of compact and multi-functional photonic devices has become a topic of major research activity in recent years. Devices have emerged that can be used for functional requirements in high speed optical data processing, filtering, nonlinear optical functions such as all-optical switching -and many other applications. The combination of photonic crystal (PhC) structures consisting of a single row of holes embedded in a narrow photonic wire (PhW) waveguide realised in high index-contrast materials is a possible contender for provision of a range of compact devices on a single chip. This trend has been motivated by the availability of a silicon technology that can support monolithic integration to form fully functional devices on CMOS chips. Results: We have successfully demonstrated experimentally an enhancement of the quality factor of a one-dimensional (1D) photonic crystal/photonic wire (PhC/PhW) microcavity that can exhibit resonance quality factor (Q-factor) values as high as 800,000 -together with a low modal volume of approximately 0.5 (λ/n) 3 . These results are based on the use of a mode matching approach previously used for device design -through the engineering of tapered hole sections within and outside the cavity -and were achieved without removing the silica cladding layer below the silicon waveguide core. The simulation results obtained in this case also agree with the experimental results obtained. Conclusions:In this work we have demonstrated that the mode matching, as light enters the photonic crystal structure, can be further enhanced through the use of careful fine tuning of the third hole, t 3 of the tapered hole region outside the cavity. The Q-factor value obtained was approximately four times greater than that achieved in our previous work on a similar structure.

With the aim of selecting particular frequencies of interest and rejecting others, the waveguiding and filtering properties of a two-dimensional phononic crystal slab are investigated in the context of a filtering application. To this end, we designed and manufactured a metallic device that consists of a square lattice of cylindrical pillars mounted on the top of a plate by using 3D printing technology. We respectively explored the theoretical and experimental characteristics of the device by using finite element method, a Micro System Analyzer (MSA) and a scanning laser Doppler vibrometer. The proposed device shows a complete band gap for Lamb wave around 0.3 MHz with a relative band-width of 30 % . Tailorable waveguides are realized inside this phononic crystal by inserting several space gaps to achieve a demultiplexing effect through the splitting of an acoustic signal towards three different bandpass frequency channels. The demultiplexing performance has been experimentally demonstrated by achieving rejection levels up to 60 dB. The proposed phononic platform can have a significant impact in signal processing as well as droplet manipulation for biological applications.

This research investigates the physicochemical properties of biopolymer succinyl-κ-carrageenan as a potential sensing material for NH4+ Localized Surface Plasmon Resonance (LSPR) sensor. Succinyl-κ-carrageenan was synthesised by reacting κ-carrageenan with succinic anhydride. FESEM analysis shows succinyl-κ-carrageenan has an even and featureless topology compared to its pristine form. Succinyl-κ-carrageenan was composited with silver nanoparticles (AgNP) as LSPR sensing material. AFM analysis shows that AgNP-Succinyl-κ-carrageenan was rougher than AgNP-Succinyl-κ-carrageenan, indicating an increase in density of electronegative atom from oxygen compared to pristine κ-carrageenan. The sensitivity of AgNP-Succinyl-κ-carrageenan LSPR is higher than AgNP-κ-carrageenan LSPR. The reported LOD and LOQ of AgNP-Succinyl-κ-carrageenan LSPR are 0.5964 and 2.7192 ppm, respectively. Thus, AgNP-Succinyl-κ-carrageenan LSPR has a higher performance than AgNP-κ-carrageenan LSPR, broader detection range than the conventional method and high selectivity toward NH4+. Interaction mechanism studies show the adsorption of NH4+ on κ-carrageenan and succinyl-κ-carrageenan were through multilayer and chemisorption process that follows Freundlich and pseudo-second-order kinetic model.

No abstract