Insulator-based (electrodeless) dielectrophoresis (iDEP) is an innovative approach in which the nonuniform electric field needed to drive DEP is produced by insulators, avoiding problems associated with the use of electrodes. Live and dead Escherichia coli were concentrated and selectively released by applying stepped DC voltages across a microchannel containing an array of insulating posts etched in glass. The only electrodes present were two platinum wires placed in the inlet and outlet reservoirs, producing mean electric fields of up to 200 V/mm across the insulators. The cells were labeled with Syto 9 and propidium iodide and imaged through a fluorescent microscope. Cell trapping and release were controlled by modifying the relative responses of electrokinesis and DEP by adjusting the magnitude of the applied voltage. Dead cells were observed to have significantly lower dielectrophoretic mobility than live cells, whereas the electrokinetic mobilities of live and dead cells were indistinguishable. The locations of the bands of differentially trapped cells were consistent with predictions. In addition, cells were selectively trapped and concentrated against backgrounds of 1- and 0.2-microm carboxylate-modified polystyrene particles. This first application of iDEP for simultaneous live/dead bacteria separation and concentration illustrates its potential as a front-end method for bacterial analysis.

Insulator-based dielectrophoresis (iDEP) was utilized to separate and concentrate selectively mixtures of two species of live bacteria simultaneously. Four species of bacteria were studied: the Gram-negative Escherichia coli and the Gram-positive Bacillus subtilis, B. cereus, and B. megaterium. Under an applied direct current (DC) electric field all the bacterial species exhibited negative dielectrophoretic behavior. The dielectrophoretic separations were carried out in a glass microchannel containing an array of insulating posts. The insulating posts in the microchannel produced nonuniformities in the electric field applied along the channel. Mixtures of two species of bacteria were introduced into the microchannel and the electric field was applied. The bacterial species exhibited different dielectrophoretic mobilities under the influence of the nonuniform field. From these experiments a trapping order was established with E. coli trapping at the weakest applied electric field, while the Bacillus species were trapped at different characteristic threshold fields. At stronger applied electric fields, the two different species of bacteria in the microchannel were dielectrophoretically trapped into two spatially distinct bands. The results showed that iDEP has the potential to selectively concentrate and separate different species of bacteria.

No abstract

We have developed porous polymer monoliths (PPMs) that are versatile and robust reversed-phase chromatography media. The PPMs are cast-to-shape, UV-cured polymers that form uniform packings within pretreated glass capillaries and fused-silica chips. No applied pressure is ever needed to flush the PPMs since they support electroosmotic flow as cast. Such characteristics make the PPMs useful for chip-based devices. Our results show efficiencies greater than or equal to 150,000 plates/m for both capillary and chip-based separations of polycyclic aromatic hydrocarbons. By changing the monomers, the hydrophobicity of the polymers, and the direction of the electroosmotic flow can be altered without degrading chromatographic performance. We describe here the development of these acrylate-based materials along with both physical and chromatographic characterization.

While cyclo-olefin polymer microchannels have the potential to improve both the optical detection sensitivity and the chemical resistance of polymer microanalytical systems, their surface properties are to date not thoroughly characterized. These surface properties dictate, among other things, electrokinetic effects when electric fields are present. Here, we report the measurement of the zeta potential of cyclo-olefin polymers (injection-molded and hot-embossed Zeonor 1060R and 1020R) microchannels as a function of pH, counter-ion concentration, storage conditions, and chemical treatment in aqueous solutions both with and without EOF-suppressing additives. In contrast with previous reports, significant surface charge is measured, consistent with titration of charged sites with pK(a) = 4.8. Storage in air, acetonitrile, or aqueous solutions has relatively minor effects. While the source of the surface charge is unclear, chemical functionalization has shown that carboxylic acid groups are not present at the surface, consistent with the chemical structure of Zeonor. EOF-suppressing additives (hydroxypropylmethylcellulose) and conditioning in perchloric acid allow the surface charge to be suppressed. We demonstrate dielectrophoretic particle trapping devices in Zeonor 1060R substrates that show reduced trapping voltage thresholds as compared to previous implementations in glass.

The first rigorous evaluation of a UV-initiated porous polymer monolith (PPM) as a stationary phase for chip electrochromatography (ChEC) is described. All channels in an offset T-injector-design-chip (25-microm deep by 50-microm wide channels) were filled by capillary action with an acrylate-based PPM precursor solution and polymerized in situ using 365 nm light for several minutes. Photodefinability of the monolith cast in the channels during the polymerization process was also demonstrated by masking off the injection arms during photoinitiation. The chromatographic performance of this chip was compared with that of chips completely filled with monolith. The detection window was photodefined after polymerization using the detection laser (257 nm doubled argon ion laser) to depolymerize the detection window. A successful ChEC separation of 10 out of 13 polycyclic aromatic hydrocarbons (PAH) was performed with on-column, off-packing laser-induced fluorescence detection at 257 nm. Van Deemter plots for early-, middle-, and late-eluting compounds showed the minimum plate height to be 5 microm. The average number of theoretical plates per meter for the PAH was 200,000. Several factors contributed to irreproducible results. Oxygen was observed to dynamically quench the fluorescence of the sample over time. Improved sealing of the reservoirs solved this problem. A within-chip variability in the retention time of 2-10% RSD was observed. These results demonstrate the feasibility and reliability of the PPM as a solid reversed-phase for electroosmotic flow-driven chip-based chromatography in microscale total analysis systems.

Efficient and robust particle separation and enrichment techniques are critical for a diverse range of lab-on-a-chip analytical devices including pathogen detection, sample preparation, high-throughput particle sorting, and biomedical diagnostics. Previously, using insulator-based dielectrophoresis (iDEP) in microfluidic glass devices, we demonstrated simultaneous particle separation and concentration of various biological organisms, polymer microbeads, and viruses. As an alternative to glass, we evaluate the performance of similar iDEP structures produced in polymer-based microfluidic devices. There are numerous processing and operational advantages that motivate our transition to polymers such as the availability of numerous innate chemical compositions for tailoring performance, mechanical robustness, economy of scale, and ease of thermoforming and mass manufacturing. The polymer chips we have evaluated are fabricated through an injection molding process of the commercially available cyclic olefin copolymer Zeonor 1060R. This publication is the first to demonstrate insulator-based dielectrophoretic biological particle differentiation in a polymeric device injection molded from a silicon master. The results demonstrate that the polymer devices achieve the same performance metrics as glass devices. We also demonstrate an effective means of enhancing performance of these microsystems in terms of system power demand through the use of a dynamic surface coating. We demonstrate that the commercially available nonionic block copolymer surfactant, Pluronic F127, has a strong interaction with the cyclic olefin copolymer at very low concentrations, positively impacting performance by decreasing the electric field necessary to achieve particle trapping by an order of magnitude. The presence of this dynamic surface coating, therefore, lowers the power required to operate such devices and minimizes Joule heating. The results of this study demonstrate that iDEP polymeric microfluidic devices with surfactant coatings provide an affordable engineering strategy for selective particle enrichment and sorting.

This review covers the application of flow injection analysis to immunoassays (FIA-IA). The advantages and limitations of this approach are discussed. Future directions, particularly those involving microfluidic systems are highlighted.