Recently, wearable pressure sensors have attracted tremendous attention because of their potential applications in monitoring physiological signals for human healthcare. Sensitivity and linearity are the two most essential parameters for pressure sensors. Although various designed micro/nanostructure morphologies have been introduced, the trade-off between sensitivity and linearity has not been well balanced. Human skin, which contains force receptors in a reticular layer, has a high sensitivity even for large external stimuli. Herein, inspired by the skin epidermis with high-performance force sensing, we have proposed a special surface morphology with spinosum microstructure of random distribution via the combination of an abrasive paper template and reduced graphene oxide. The sensitivity of the graphene pressure sensor with random distribution spinosum (RDS) microstructure is as high as 25.1 kPa in a wide linearity range of 0-2.6 kPa. Our pressure sensor exhibits superior comprehensive properties compared with previous surface-modified pressure sensors. According to simulation and mechanism analyses, the spinosum microstructure and random distribution contribute to the high sensitivity and large linearity range, respectively. In addition, the pressure sensor shows promising potential in detecting human physiological signals, such as heartbeat, respiration, phonation, and human motions of a pushup, arm bending, and walking. The wearable pressure sensor array was further used to detect gait states of supination, neutral, and pronation. The RDS microstructure provides an alternative strategy to improve the performance of pressure sensors and extend their potential applications in monitoring human activities.

The synaptic activities in the nervous system is the basis of memory and learning behaviors, and the concept of biological synapse has also spurred the development of neuromorphic engineering. In recent years, the hardware implementation of the biological synapse has been achieved based on CMOS circuits, resistive switching memory, and field effect transistors with ionic dielectrics. However, the artificial synapse with regulatable plasticity has never been realized of the device level. Here, an artificial dynamic synapse based on twisted bilayer graphene is demonstrated with tunable plasticity. Due to the ambipolar conductance of graphene, both behaviors of the excitatory synapse and the inhibitory synapse could be realized in a single device. Moreover, the synaptic plasticity could also be modulated by tuning the carrier density of graphene. Because the artificial synapse here could be regulated and inverted via changing the bottom gate voltage, the whole process of synapse development could be imitated. Hence, this work would offer a broad new vista for the 2D material electronics and guide the innovation of neuro-electronics fundamentally.

We report an artificial eardrum using an acoustic sensor based on two-dimensional MXene (Ti 3 C 2 T x ), which mimics the function of a human eardrum for realizing voice detection and recognition. Using MXene with a large interlayer distance and micropyramid polydimethylsiloxane arrays can enable a two-stage amplification of pressure and acoustic sensing. The MXene artificial eardrum shows an extremely high sensitivity of 62 kPa −1 and a very low detection limit of 0.1 Pa. Notably, benefiting from the ultrasensitive MXene eardrum, the machine-learning algorithm for real-time voice classification can be realized with high accuracy. The 280 voice signals are successfully classified for seven categories, and a high accuracy of 96.4 and 95% can be achieved by the training dataset and the test dataset, respectively. The current results indicate that the MXene artificial intelligent eardrum shows great potential for applications in wearable acoustical health care devices.

Surface acoustic wave (SAW) devices have been widely used in different fields and will continue to be of great importance in the foreseeable future. These devices are compact, cost efficient, easy to fabricate, and have a high performance, among other advantages. SAW devices can work as filters, signal processing units, sensors and actuators. They can even work without batteries and operate under harsh environments. In this review, the operating principles of SAW sensors, including temperature sensors, pressure sensors, humidity sensors and biosensors, will be discussed. Several examples and related issues will be presented. Technological trends and future developments will also be discussed.

With the aging of society and the increase in people’s concern for personal health, long-term physiological signal monitoring in daily life is in demand. In recent years, electronic skin (e-skin) for daily health monitoring applications has achieved rapid development due to its advantages in high-quality physiological signals monitoring and suitability for system integrations. Among them, the breathable e-skin has developed rapidly in recent years because it adapts to the long-term and high-comfort wear requirements of monitoring physiological signals in daily life. In this review, the recent achievements of breathable e-skins for daily physiological monitoring are systematically introduced and discussed. By dividing them into breathable e-skin electrodes, breathable e-skin sensors, and breathable e-skin systems, we sort out their design ideas, manufacturing processes, performances, and applications and show their advantages in long-term physiological signal monitoring in daily life. In addition, the development directions and challenges of the breathable e-skin are discussed and prospected.

Stearate-pillared layered double hydroxide (LDH) promoted by K 2 CO 3 as a precursor for pre-combustion of a CO 2 adsorbent is presented for the first time. This novel precursor is synthesized from commercial hydrotalcite, one kind of LDH, undergoing acid-aid anionic exchange and wet impregnation processes. The pillared stearate expands the gallery height from 0.28 nm for carbonate-intercalated LDH (almost the diameter of the K ion, 0.276 nm) to a much spatial 3.4 nm for stearate-intercalated LDH, proven by characteristic diffraction peaks in powder X-ray diffraction (PXRD). Transmission electron microscopy (TEM) micrographs and energy-dispersive X-ray spectroscopy (EDX) provide a vivid layout of K and its on-spot composition, respectively, deducing that a well-dispersed K ion promotion exists inside brucite-like layers. Experimental results carried out by a thermogravimetric analyzer (TGA) show striking CO 2 capacity up to 1.93 mmol g −1 at 300°C, 1.7 times higher than that of a conventional K 2 CO 3 -promoted hydrotalcite adsorbent (1.11 mmol g −1 ), and fast adsorption kinetics for this precursor.

No abstract

Two-dimensional (2D) hybrid perovskite sandwiched between two long-chain organic layers is an emerging class of low-cost semiconductor materials with unique optical properties and improved moisture stability. Unlike conventional semiconductors, ion migration in perovskite is a unique phenomenon possibly responsible for long carrier lifetime, current–voltage hysteresis, and low-frequency giant dielectric response. While there are many studies of ion migration in bulk hybrid perovskite, not much is known for its 2D counterparts, especially for ion migration induced by light excitation. Here, we construct an exfoliated 2D perovskite/carbon nanotube (CNT) heterostructure field effect transistor (FET), not only to demonstrate its potential in photomemory applications, but also to study the light induced ion migration mechanisms. We show that the FET I–V characteristic curve can be regulated by light and shows two opposite trends under different CNT oxygen doping conditions. Our temperature-dependent study indicates that the change in the I–V curve is probably caused by ion redistribution in the 2D hybrid perovskite. The first principle calculation shows the reduction of the migration barrier of I vacancy under light excitation. The device simulation shows that the increase of 2D hybrid perovskite dielectric constant (enabled by the increased ion migration) can change the I–V curve in the trends observed experimentally. Finally, the so synthesized FET shows the multilevel photomemory function. Our work shows that not only we could understand the unique ion migration behavior in 2D hybrid perovskite, it might also be used for many future memory function related applications not realizable in traditional semiconductors.