In this article, we report on the heat-transfer resistance at interfaces as a novel, denaturation-based method to detect single-nucleotide polymorphisms in DNA. We observed that a molecular brush of double-stranded DNA grafted onto synthetic diamond surfaces does not notably affect the heat-transfer resistance at the solid-to-liquid interface. In contrast to this, molecular brushes of single-stranded DNA cause, surprisingly, a substantially higher heat-transfer resistance and behave like a thermally insulating layer. This effect can be utilized to identify ds-DNA melting temperatures via the switching from low- to high heat-transfer resistance. The melting temperatures identified with this method for different DNA duplexes (29 base pairs without and with built-in mutations) correlate nicely with data calculated by modeling. The method is fast, label-free (without the need for fluorescent or radioactive markers), allows for repetitive measurements, and can also be extended toward array formats. Reference measurements by confocal fluorescence microscopy and impedance spectroscopy confirm that the switching of heat-transfer resistance upon denaturation is indeed related to the thermal on-chip denaturation of DNA.

Most challenging in the development of DNA sensors is the ability to distinguish between fully complementary target ssDNA (single-strand DNA) and 1-mismatch ssDNA. To deal with this problem, we performed impedance spectroscopy on DNA-functionalized nanocrystalline diamond (NCD) layers during hybridization and denaturation. In both reactions, a difference in behavior was observed for 1-mismatch target DNA and complementary target DNA in real-time. During real-time hybridization, a decrease of the impedance was observed at lower frequencies when the complementary target DNA was added, while the addition of 1-mismatch target ssDNA caused no significant change. Fitting these results to an electrical circuit demonstrates that this is correlated with a decrease of the depletion zone in the space charge region of the diamond. During real-time denaturation, differentiation between 1-mismatch and complementary target DNA was possible at higher frequencies. Denaturation of complementary DNA showed the longest exponential decay time of the impedance, while the decay time during 1-mismatch denaturation was the shortest. The real-time hybridization and denaturation experiments were carried out on different NCD samples in various buffer solutions at temperatures between 20 and 80 degrees C. It was revealed that the best results were obtained using a Microhyb hybridization buffer at 80 degrees C and 10x PCR buffer at 30 degrees C for hybridization and 0.1 M NaOH at temperatures above 40 degrees C for denaturation. We demonstrate that the combination of real-time hybridization spectra and real-time denaturation spectra yield important information on the type of target. This approach may allow a reliable identification of the mismatch sequence, which is the most biologically relevant.

No abstract

In this article, we report on the electronic monitoring of DNA denaturation by NaOH using electrochemical impedance spectroscopy in combination with fluorescence imaging as a reference technique. The probe DNA consisting of a 36-mer fragment was covalently immobilized on nanocrystalline-diamond electrodes and hybridized with different types of 29-mer target DNA (complementary, single-nucleotide defects at two different positions, and a non-complementary random sequence). The mathematical separation of the impedimetric signals into the time constant for NaOH exposure and the intrinsic denaturation-time constants gives clear evidence that the denaturation times reflect the intrinsic stability of the DNA duplexes. The intrinsic time constants correlate with calculated DNA-melting temperatures. The impedimetric method requires minimal instrumentation, is label-free and fast with a typical time scale of minutes and is highly reproducible. The sensor electrodes can be used repetitively. These elements suggest that the monitoring of chemically induced denaturation at room temperature is an interesting approach to measure DNA duplex stability as an alternative to thermal denaturation at elevated temperatures, used in DNA-melting experiments and single nucleotide polymorphism (SNP) analysis.

The covalent attachment method for DNA on nanocrystalline diamond (NCD), involving the introduction of COOH functionalities on the surface by photoattachment of 10-undecenoic acid (10-UDA), followed by the 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide (EDC)-mediated coupling to NH 2-labeled ssDNA, is evaluated in terms of stability, density, and functionality of the resulting biological interface. This is of crucial importance in DNA biosensor development. The covalent nature of DNA attachment will infer the necessary stability and favorable orientation to the ssDNA probe molecules. Using confocal fluorescence microscopy, the influence of buffer type for the removal of excess 10-UDA and ssDNA, the probe ssDNA length, the probe ssDNA concentration, and the presence of the COOH-linker on the density and functionality of the ssDNA probe layer were investigated. It was determined that the most homogeneously dense and functional DNA layer was obtained when 300 pmol of short ssDNA was applied to COOH-modified NCD samples, while H-terminated NCD was resistant for DNA attachment. Exploiting this surface functionality dependence of the DNA attachment efficiency, a shadow mask was applied during the photochemical introduction of the COOH-functionalities, leaving certain regions on the NCD H-terminated. The subsequent DNA attachment resulted in a fluorescence pattern corresponding to the negative of the shadow mask. Finally, NCD surfaces covered with mixtures of the 10-UDA linker molecule and a similar molecule lacking the COOH functionality, functioning as a lateral spacer, were examined for their suitability in preventing nonspecific adsorption to the surface and in decreasing steric hindrance. However, purely COOH-modified NCD samples, patterned with H-terminated regions and treated with a controlled amount of probe DNA, proved the most efficient in fulfilling these tasks.

No abstract

This article reviews the current state‐of‐the art of diamond‐based DNA sensors. Some general concepts involved in biosensors are introduced and applied to DNA sensors. The properties of chemically vapor deposited (CVD) diamond relevant for this application are summed up, with special attention for the stability and bio‐compatibility of the material. Several routes to functionalize the diamond surface are considered. The physical properties of the obtained DNA layers are discussed in terms of surface density and molecular conformation. Possible read‐out strategies are evaluated, including optical and electronic sensing. With diamond‐based DNA sensors, real‐time and label‐free sensing is achieved. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)

Label-free detection of DNA molecules on chemically vapor-deposited diamond surfaces is achieved with spectroscopic ellipsometry in the infrared and vacuum ultra-violet range. This non-destructive method has the potential to yield information on the average orientation of single as well as double stranded DNA molecules, without restricting the strand length to the persistence length. The orientational analysis based on electronic excitations in combination with information from layer thicknesses, provides a deeper understanding of biological layers on diamond. The π-π* transition dipole moments, corresponding to a transition at 4.74 eV, originate from the individual bases. They are in a plane perpendicular to the DNA backbone with an associated n-π* transition at 4.47 eV. For 8-36 bases of single and double stranded DNA covalently attached to ultra-nanocrystalline diamond, the ratio between in-and out-of-plane components in the best fit simulations to the ellipsometric spectra yields an average tilt angle of the DNA backbone with respect to the surface plane ranging from 45° to 52°. 2We comment on the physical meaning of the calculated tilt angles. Additional information is gathered from atomic force microscopy, fluorescence imaging, and wetting experiments. The results reported here are of value in understanding and optimizing the performance of the electronic read-out of a diamond-based label-free DNA hybridization sensor.