Laser powder bed fusion (L-PBF) of copper alloys with high copper content is difficult due to the high infrared reflectivity and thermal conductivity of these alloys. In this study a simple and scalable method for coating copper powder with tin and nickel is presented, and suggested as an alloying strategy for such alloys. The coated powders were processed in a commercial L-PBF-machine at various scanning speeds. The samples made from coated powders show a lower amount of porosity compared to samples made from in-situ alloyed powders of similar composition.
The solid-phase reactions of copper with tin are considered, and the porosity of the reaction products depending on the pretreatment of the copper substrate is investigated. Copper substrates for the reaction are prepared by electrodeposition of copper layers with thickness of up to 100 microns on the rolled copper plates. The defects of substrates are determined by the different modes of electrodeposition-stationary, reversible, and stochastic ones. As shown, the thicknesses of the intermediate phases, their ratio, the number and spatial distribution of pores in the reaction products significantly depend on the mode of electrodeposition. The statistical dependences of the pore distribution along and across the interface as well as the characteristics of the roughness of the interface are revealed.Розглядаються твердофазні реакції міді з циною, та досліджується поруватість продуктів реакції в залежності від попереднього оброблення мідного підложжя. Мідні підложжя для реакції готуються шляхом електроосадження прошарків міді товщиною до 100 мкм на прокатані мідні пла-Corresponding author: V. V. Morozovych Îттиски доступнû непосредственно от издателя Ôотокопирование разрешено только в соответствии с лицензиеé 2018 ÈМÔ (Èнститут металлофизики им. Ã. Â. Êурдюмова ÍÀÍ Óкраинû) Íапе÷атано в Óкраине. 1649 1650 V. V. MOROZOVYCH, A. R. HONDA, Yu. O. LYASHENKO et al. тівки. Дефектність підложжя визна÷ається різними режимами електроосадження: стаціонарним, реверсним і стохасти÷ним. Показано, що товщини проміжних фаз, їх відношення, кількість і просторовиé розподіл пор у продуктах реакції істотно залежать від режиму електроосадження. Âиявлено статисти÷ні залежності розподілу пор вздовж і поперек інтерфеéсу, а також характеристики éого шерсткости. Ключові слова: інтерфеéс мідь-цина, дифузія, твердофазні реакції, електроосадження, дефекти, пороутворення, пінінґування. Рассматриваются твёрдофазнûе реакции меди с оловом, и исследуется пористость продуктов реакции в зависимости от предварительноé обработки медноé подложки. Меднûе подложки для реакции готовятся путём электроосаждения слоёв меди толщиноé до 100 мкм на прокатаннûе меднûе пластинки. Дефектность подложек определяется разли÷нûми режимами электроосаждения: стационарнûм, реверсивнûм и стохасти÷еским. Показано, ÷то толщинû промежуто÷нûх фаз, их соотношение, коли÷ество и пространственное распределение пор в продуктах реакции существенно зависят от режима электроосаждения. Óстановленû статисти÷еские зависимости распределения пор вдоль и поперёк интерфеéса, а также характеристики его шероховатости. Ключевые слова: интерфеéс медь-олово, диффузия, твёрдофазнûе реакции, электроосаждение, дефектû, порообразование, пиннинг.
64.70.kd, 82.40.ck, 66.30.Ny СТРУКТУРНИЙ СТАН ГАЛЬВАНООСАДЖЕНИХ ПРОШАРКІВ МІДІ * Методами рентгенівського дифракційного аналізу досліджено мікроструктуру прошарків міді, що отримані електроосадженням міді в стаціонарному, реверсному імпульсному та стохастичному режимах на мідні підкладки. Встановлено суттєвий вплив форми струму на текстуру осаджених прошарків міді. Було встановлено, що більш просторово однорідну структуру має осад, що отриманий в реверсному імпульсному режимі електроосадження. За постійного струму електроосадження формуються кристали з більш дефектною структурою. За допомогою аналізу уширення дифракційних ліній визначено розміри областей когерентного розсіювання в прошарках, що отримані за різних режимів струму. Також встановлено, що після електролітичного осадження міді розмір зерен зменшується, порівняно з розмірами зерен в полікристалічній мідній підкладці. Ключові слова: електроосадження, рентгеноструктурний аналіз, мідь, області когерентного розсіювання, дифрактограма.
Досліджено вплив ультразвукового перемішуваня на процес хімічного осадження олова на порошкову мідь. Встановлено, що використання ультразвукового диспергатора в процесі хімічного осадження олова на мідний порошок впливає на швидкість росту фази Cu6Sn5. Проаналізовано фазовий склад порошків, що отримані у ході хімічного осадження олова та проведено кількісний аналіз утворених фаз після процесу хімічного осадження олова на мідний порошок.Ключові слова: хімічне осадження, растрова електронна мікроскопія, мідь, олово, ультразвуковий диспергатор. ВступПерехід до нанотехнологій в електротехніці та приладобудуванні зумовлює необхідність пошуку шляхів локального осадження тонких прошарків припою, що використовуються у процесі спаювання елементів електротехніки та виготовлення окремих деталей приладів [1]. Нанесення припоїв у вигляді таблеток, дроту, фольги або занурення виробу в розплав не дозволяє зберегти форму і розміри елементів виробу. Альтернативними варіантами є локальне нанесення паяльних паст, в яких припой знаходиться у вигляді мікро або наночастинок у матриці флюсу, або осадження припою у вигляді плівок із застосуванням вакуумних технологій або відновленням металів з розчинів (хімічне осадження) [2].Припої на основі олова та його сплавів з міддю знайшли широке технологічне застосування завдяки таким корисним властивостям, як низька температура плавлення,
64.70.kd, 82.40.ck, 66.30.Ny * Статтю написано згідно з прикладною держбюджетною темою "Синтез наноструктурованих сплавів за осцилюючих напружень та їх застосування в новій технології з'єднання мікроелектронних компонентів" (номер державної реєстрації 0117U000577).
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.