The aim of this study was to evaluate the effects of different techniques of surface treatment on the microleakage of a fissure sealant in molar teeth. A total of 50 freshly extracted noncarious human third molars were randomly assigned to one of five groups. Occlusal fissures were treated with one of the following: acid etching with 35% orthophosphoric acid (group 1); fissurotomy with a Fissurotomy Micro NTF metal bur (group 2); laser etching with an Er,Cr:YSGG laser at 2 W and 20 Hz (group 3); laser etching with an Er,Cr:YSGG laser at 2 W and 40 Hz (group 4); and air abrasion for 20 s with 30-µm Al(2)O(3) particles via a CoJet Prep device (group 5). After surface pretreatment, a resin-based sealant was applied to the fissures. The sample teeth were subjected to thermocycling and stored in distilled water at 37°C for 1 month. Following immersion in 0.5% basic fuchsin solution for 24 h, three buccolingual slices of each sample tooth were scored under a stereomicroscope, and the morphological appearance of the area between the enamel surface and fissure sealant was examined under a scanning electron microscope. The Kruskal-Wallis test and one-way ANOVA revealed significant differences in marginal leakage, as follows: group 1 showed significantly lower scores than groups 2 and 5, the scores of groups 1, 3 and 4 were not significantly different, and group 2 showed significantly higher scores than groups 3 and 4. Laser irradiation, the metal bur, and the CoJet Prep device did not eliminate the need for acid etching of the enamel prior to placement of a fissure sealant. Laser etching at 2 W (20 Hz or 40 Hz) may be an alternative to conventional acid-etching.

Differences were found between EXPs regarding MS levels at days 1, 7 and 60 as well as for LB at all time periods (p<0.05). VHN decreased in EXPs compared to CNTs (p<0.05), and no differences were found between EXPs (p>0.05). CFR patterns tended to decrease in EXPs compared to the CNTs, but no differences were found between EXPs (p>0.05) CLINICAL SIGNIFICANCE These mixtures could be recommended for ART procedures to provide beneficial antibacterial effects without seriously deteriorating the physical properties of selected GICs.

No abstract

The retention of GIC sealants was markedly inferior to the retention of resin-based sealants; however, GIC when used as a pit and fissure sealant was slightly more effective in preventing occlusal caries.

Preoperative use of ibuprofen and paracetamol may provide a pre-emptive analgesic effect in paediatric patients who receive adequate analgesia during mandibular primary tooth extraction.

In atraumatic restorative treatment (ART), caries removal with hand excavation instruments is not as efficient as that with rotary burs in eliminating bacteria under the glass ionomer cements (GICs). Thus, different antibacterial agents have been used in recent studies to enhance the antibacterial properties of the GICs, without jeopardizing their basic physical properties. ObjectiveThe objective of this study was to evaluate the effect of antibacterial agents on the surface hardness of a conventional GIC (Fuji IX) using Vickers microhardness [Vickers hardness number (VHN)] test. Material and MethodsCetrimide (CT), cetylpyridinium chloride (CPC) and chlorhexidine (CHX) were added to the powder and benzalkonium chloride (BC) was added to the liquid of Fuji IX in concentrations of 1% and 2%, and served as the experimental groups. A control group containing no additive was also prepared. After the completion of setting reaction, VHN measurements were recorded at 1, 7, 15, 30, 60, and 90 days after storage in 37ºC distilled water. A one-way ANOVA was performed followed by a Dunnett t test and Tamhane T2 tests and also repeated measurements ANOVA was used for multiple comparisons in 95% confidence interval. ResultsVHN results showed significant differences between the control and the experimental groups at all time periods (p<0.05 for all). Significant differences were observed between all study periods for individual groups (p<0.05). After 7 days, VHNs were decreased in all experimental groups while they continued to increase in the control group. BC and CHX groups demonstrated the least whereas CT and CPC groups exhibited most adverse effect on the hardness of set cements. ConclusionsDespite the decreased microhardness values in all experimental groups compared to the controls after 7 up to 90 days, incorporating certain antibacterial agents into Fuji IX GIC showed tolerable microhardness alterations within the limitations of this in vitro study.

Ectodermal dysplasia is a hereditary disorder that occurs as a consequence of disturbances in the ectoderm of the developing embryo. The triad of nail dystrophy, alopecia or hypotrichosis and palmoplantar hyperkeratosis is usually accompanied by a lack of sweat glands and a partial or complete absence of primary and/or permanent dentition. Two case reports illustrating the prosthetic rehabilitation of 2 young boys with anhidrotic ectodermal dysplasia associated with severe anodontia are presented. Since the oral rehabilitation of these cases is often difficult; particularly in pediatric patients, treatment should be administered by a multidisciplinary team involving pediatric dentistry, orthodontics, prosthodontics and oral-maxillofacial surgery.

No abstract