Interior thermal insulation is frequently one of the only possible solutions for thermal upgrade of the building envelope where the external appearance cannot be changed. In this study, four insulation materials were used in a case study in a historical school building in in situ test walls. The indoor climate in the test room was controlled to simulate the typical dwelling with high moisture load. The temperatures, relative humidity, and heat flows were monitored over 9 months to analyze the hygrothermal performance of four different insulation materials. The hygrothermal performance of insulation materials during drying and wetting periods are presented. Moisture test reference year was used in working out possible energy-renovation solutions. The results show that timing of the renovation works is a matter of consideration to avoid the hygrothermal risks inside the renovated wall assemblies. The results show that in all the cases, thermal comfort can be improved by increasing the inner surface temperature and decreasing thermal conductivity. However, in some cases, the risks of mold growth and interstitial condensation were present inside the retrofitted wall assemblies. Computer simulations of the wall assemblies with moisture reference years under different humidity loads concluded that all solutions are suitable for future analysis.
Hygrothermal simulations are of major importance for critical problems in building physics, such as the application of internal insulation in heritage buildings. These simulations require numerous material parameters that are challenging to determine. We present measurements of typical internal insulation materials, calcium-silicate and autoclaved aerated concrete, which we expose to a warm, humid climate on one side and a cold temperature on the other side. We measure the moisture gain over time and determine the moisture profile at experiment end. In an inverse modelling approach, the measurements are used to identify material parameters, in particular vapour conductivity and capillary conductivity as a function of moisture content. We found the measurements of crucial importance for the accurate determination of these parameters. When the parameters rely only on isothermal measurements such as the drying experiment, the model fails to predict the capillary condensation process. We demonstrate this on a dataset from another study with interior insulation subjected to changing boundary conditions. The model calibrated with capillary condensation data reliably reconstructs measurements while the drying-calibrated model drastically underestimates the moisture content.
Reliable hygrothermal modelling depends on the quality of material characterization, especially so when higher moisture contents are concerned. Previous research has shown that adding additional material tests (e.g. capillary condensation redistribution (CCR) test) to the experimental dataset brings improvements to the modelling accuracy, but also adds to the workload of characterization process. This paper discusses a generative optimization workflow to increase the speed of the characterization and quality of the result. The proposed workflow incorporates optimization tool GenOpt and hygrothermal modelling software IBK Delphin to search for best fit of the water vapour and liquid conductivity curves of interior insulation materials based on modelling the CCR, drying and wet cup tests. Finally, models using material data from the proposed workflow and from the software database are compared to measurement results from two studies on interior thermal insulation. The results suggest that the generative optimization shows promise on the grounds of reducing tedious work analysing material tests. Also, a wider experimental dataset is shown to be useful when characterizing the vapour and liquid conductivity functions in over-hygroscopic region.
Interior insulation of historic buildings is well-studied in Central Europe; however, their conclusions might not be directly applicable to colder climates. Heat, air and moisture (HAM) modelling can be a valuable tool for studying those solutions in different conditions. Recently, incorporating the capillary condensation redistribution (CCR) test into the material characterization process has shown to cause dramatic improvement in correlating hygrothermal modelling results to measurements in certain situations. It is also noteworthy, that the HAM modelling errors made using material data from conventional characterization process can be severely non-conservative. In this article a parametric study of a 51 cm thick mass masonry wall is undertaken to determine the effect of the improved material properties on the reliability of a vapour open ‘capillary active’ autoclaved aerated concrete (AAC) and calcium silicate (CaSi) interior insulation solutions and to compare them to a vapour tight insulation system. A 49-year real weather dataset from Estonia is used. The results show that compared to conventionally characterized material properties the CCR-optimized material data causes more critical conditions directly behind the interior insulation, while having a similar performance in the exterior part of the masonry. The differences occur close to the performance limits and highlight the importance of using the CCR test in material characterization process. The vapour tight and vapour open systems showed a very similar impact on the freeze-thaw cycles and on the maximum ice saturation of the exterior part of the masonry. The vapour open solutions perform better than the vapour tight PIR in terms of frost damage and possible mould growth behind the insulation – even though the advantage has been reduced when using the CCR-optimized material data. Regardless of the insulation solution, a case-specific approach is still required to avoid damaging the original wall and/or the added insulation system.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.