ABSTRACT:The novel thiourea-functionalized silicon nanoparticles (SiNPs) have been successfully synthesized using allylamine and sulforaphane, an important anticancer drug, followed by a hydrosilylation reaction on the surface of hydrogen terminated SiNPs. Their physiochemical properties have been investigated by photoluminescence emission, FTIR and elemental analysis. MTT assay has been employed to evaluate in vitro toxicity in colorectal cancer cells (Caco-2) and primary normal cells (CCD). The results show significant toxicity of thiourea SiNPs after 72 h incubation in the cancer cell line and the toxicity is concentration dependent and saturated for concentrations above 100 µg/mL. Confocal microscopy images have demonstrated the internalization of thiourea-functionalized SiNPs inside the cells. Flow cytometry data has confirmed receptor-mediated targeting in cancer cells. This nanocomposite takes advantage of the EGFR active targeting of the ligand in addition to the photoluminescence properties of SiNPs for bioimaging purposes. The results suggest that this novel nanosystem can be extrapolated for active targeting of the receptors that are overexpressed in cancer cells such as EGFR using the targeting characteristics of thiourea-functionalized SiNPs and therefore encourage further investigation and development of anticancer agents specifically exploiting the EGFR inhibitory activity of such nanoparticles.
In this work, we demonstrate doping graphene oxide (GO) films using a low power atmospheric pressure plasma jet (APPJ) with subsequent tuning of the work function.
Halide perovskite indoor photovoltaics (PV) are a viable solution to autonomously power the billions of sensors in the huge technology field of the Internet of Things. However, there exists a knowledge gap in the hysteresis behaviour of these photovoltaic devices under indoor lighting conditions. The present work is the first experimental study dedicated to exploring the degree of hysteresis in halide perovskite indoor photovoltaic devices by carrying out both transient J–V scan and steady state maximum power point tracking (MPPT) measurements. Dependence of hysteresis on device architecture, selection of electron transporting layers and the composition of the perovskite photoactive layers were investigated. Under indoor illumination, the p-i-n MAPbI
3
-based devices show consistently high power conversion efficiency (PCE) (stabilized PCE) of greater than 30% and negligible hysteresis behaviour, whereas the n-i-p MAPbI
3
devices show poor performance (stabilized PCE ∼ 15%) with pronounced hysteresis effect. Our study also reveals that the n-i-p triple cation perovskite devices are more promising (stabilized PCE ∼ 25%) for indoor PV compared to n-i-p MAPbI
3
due to their suppressed ion migration effects. It was observed that the divergence of the PCE values estimated from the J–V scan measurements, and the maximum power point tracking method is higher under indoor illumination compared to 1 Sun, and hence for halide perovskite-based indoor PV, the PCE from the MPPT measurements should be prioritized over the J–V scan measurements. The results from our study suggest the following approaches for maximizing the steady state PCE from halide perovskite indoor PV: (i) select perovskite active layer composition with suppressed ion migration effects (such as Cs-containing triple cation perovskites) and (ii) for the perovskite composition such as MAPbI
3
, where the ion migration is very active, p-i-n architecture with organic charge transport layers is beneficial over the n-i-p architecture with conventional metal oxides (such as TiO
2
, SnO
2
) as charge transport layers.
This article is part of the theme issue ‘Developing resilient energy systems’.
Integration of nanotechnology and advanced manufacturing processes presents an attractive route to produce devices for adaptive biomedical device technologies.
A process was developed to disperse β-SiC nanoparticles (NPs), with a high propensity to agglomerate, within a matrix of A356 aluminum alloy. A suitable dispersion of 1 wt.% SiC NPs in the A356 matrix was obtained through a hybrid process including a solid-state modification on the surface of the NPs, a two-step stirring process in the semi-solid and then the liquid-state, and a final hot-rolling process for fragmentation of the brittle eutectic silicon phase and porosity elimination. Titanium and nickel where used as the nanoparticle SiC surface modifiers. Both modifiers were found to improve the mechanical properties of the resulting material, however, the highest improvement was found from the nickel surface modification. For the nickel modification, compared to the non-reinforced rolled alloy, more than a 77 %, 85 %, and 70 % increase in ultimate tensile strength (UTS), yield strength (YS), and strain % at the break, respectively were found with respect to the unreinforced rolled A356. For the rolled nanocomposite containing 1 wt. % SiCnp and nickel modification, an average YS, UTS, and strain % at the break of 277MPa, 380 MPa, and 16.4% were obtained, respectively, which are unique and considerable property improvements for A356 alloy.
A technique to increase the conductivity of Spiro-OMeTAD using an easily scalable, nonthermal atmospheric pressure plasma jet (APPJ) is reported. An investigation of plasma functionalization demonstrated an enhancement in hole conductivity by over an order of magnitude from 9.4 × 10-7 S cm-1 for the pristine film to 1.15 × 10-5 S cm-1 for films after 5 minutes of plasma treatment. The conductivity value after plasma functionalization was comparable to that reported for 10 -25% Li-TFSI-doped Spiro-OMeTAD. The increase in conductivity was correlated with a reduction in phase value observed using electrostatic force microscopy. Kelvin probe force microscopy showed an increase in work function after plasma exposure corresponding to the p-type nature of the doping. X-ray photoelectron spectroscopy revealed surface oxidation of plasma-functionalized films, as well as variation in nitrogen chemistry, with the formation of a higher binding energy quaternary nitrogen tail. Oxidation of Spiro-OMeTAD was also confirmed by the appearance of the 500 nm absorption peak using UV-vis spectroscopy. The synergistic contribution of increase in charge density in Spiro-OMeTAD due to the energetic species in the plasma jet coupled with improvement in π-π stacking of the molecules is thought to underlie the conductivity enhancement. We also attribute the formation of quinoid structures with quaternary nitrogen +N=C to the enhancement in positive charge centres due to loss of methoxy groups during plasma-surface interaction. This work opens up the possibility of using an atmospheric pressure plasma jet as a simple and effective technique for doping and functionalizing Spiro-OMeTAD thin films to circumvent the detrimental issues associated with chemical dopants.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.