No abstract

Controlled pore size and desirable internal architecture of bone scaffolds play a significant role in bone regeneration efficiency. In addition to choosing appropriate materials, the manufacturing method is another significant factor in fabricating the ideal scaffold. In this study, scaffolds were designed and fabricated by the fused filament fabrication (FFF) technique. Polycaprolactone (PCL) and composites films with various percentages of hydroxyapatite (HA) (up to 20%wt) were used to fabricate filaments. The influence of (HA) addition on the mechanical properties of filaments and scaffolds was investigated. in vitro biological evaluation was examined as well as the apatite formation in simulated body fluid (SBF). The addition of HA particles increased the compressive strength and Young’s modulus of filaments and consequently the scaffolds. Compared to PCL, Young’s modulus of PCL/HA20% filament and three-dimensional (3D) printed scaffold has increased by 30% and 50%, respectively. Also, Young’s modulus for all scaffolds was in the range of 30–70 MPa, which is appropriate to use in spongy bone. Besides, the MTT assay was utilized to evaluate cell viability on the scaffolds. All the samples had qualified cytocompatibility, and it would be anticipated that addition of HA particles raise the biocompatibility in vivo. Alkaline phosphatase (ALP) evaluation shows that the addition of HA caused higher ALP activity in the PCL/HA scaffolds than PCL. Furthermore, calcium deposition in the PCL/HA specimens is higher than control. In conclusion, the addition of HA particles into the PCL matrix, as well as utilizing an inexpensive commercial FFF device, lead to the fabrication of scaffolds with proper mechanical and biological properties for bone tissue engineering applications.

The suggested optimized hydrogel was a suitable candidate as a biopaper for skin bioprinting technology.

No abstract

Three-dimensional (3D) printing becomes an attractive technique to fabricate tissue engineering scaffolds through its high control on fabrication and repeatability using the printing parameters. This technique can be combined by the finite element method (FEM), and tissue-specific scaffolds with desirable morphological and mechanical properties can be designed and manufactured. In this study, the influential 3D printing parameters on the morphological and mechanical properties of polycaprolactone (PCL) filament and scaffold were studied experimentally and numerically. First, the effects of printing parameters and process on the properties of extruded PCL filament were investigated. Then, using FEM, the effects of filament specifications on the overall characteristics of the scaffold were evaluated. Results showed that both the printing process in terms of resting time and remaining time and the printing parameters like pressure, printing speed, and printing path length have influenced the filament properties. In addition, both the filament diameter and elastic modulus had significant effects on the properties of scaffold especially, a 20% increase in the filament diameter caused the scaffold compressive elastic modulus to rise by around 72%. It is concluded that the printing parameters and process must be tuned very well in fabricating scaffolds with the desired morphology and mechanical property.

The design of porous gradient scaffolds for bone tissue engineering scaffolds is a relatively new approach. This strategy is based on imitating bone tissue in order to stimulate enhanced cellular responses. An additive manufacturing (AM) method, such as the fused filament fabrication (FFF) system, provides precise and repeatable pore size control. FFF is a well-known AM manufacturing process for producing high-quality parts at a low cost. In this study, polycaprolactone (PCL) and variable hydroxyapatite (HA) amounts were fed into a FFF printer to print four scaffold designs with different porosity gradients. These porous gradient scaffolds were constructed using simple (Si) and shifting (Sh) models, with gradient pore diameters ranging from 400-600 to 400-800 μm. The specimens featured thicker walls but more open cores. The scaffolds' structural, mechanical, and biological properties were evaluated. The results showed that higher gradient porosity and larger pore size led to better biological results, but lower mechanical strength resulted. Furthermore, adding HA increased mechanical strength from 81.8% to 100% and enhanced cellular response. In all scaffolds, an increase in porosity and a decrease in density led to a reduction in compressive strength. The toxicity of the samples and cellular adhesion was evaluated using MTT and DAPI tests on hFOB (human Fetal OsteoBlastic) cells. Alkaline phosphatase and Red Alizarin analyses demonstrated an increase in mineralization as HA content increased.

Blood wicking in its steady-state form, i.e. the uniform distribution of blood cells in plasma, is completely different from that in its coagulated form on a porous surface like paper. The hydrophilic property of the cellulose leads to a significant wicking of the blood cells on paper fibers after rinsing with isotonic solution. The difference in the wicking length of the blood cells in steady state and that in the coagulated form could be considered as a criterion to recognize the blood type in a paper-based kit. However, owing to the molecular structure of the nitrocellulose, a better process occurs while separating the coagulated blood from the steady-state form of cells. Therefore, it is possible to use the nitrocellulose for the blood-typing kit which leads to a simpler way to diagnose a blood type. Two series of experiments were performed on nitrocellulose membrane. First, antibody solutions and blood samples were sequentially absorbed on nitrocellulose strips, allowed to interact, rinsed with an isotonic solution and distilled water, and image processing performed on a digital picture of the remaining blood cells. The efficiency of the agglutinated blood cell fixation was quantified by red color intensity. Then, it was demonstrated that there is no considerable difference in fixation of agglutinated blood cells with rinsing using isotonic and nonisotonic solutions. This fact can be a considerable advantage over paper since it can eliminate the probable mistake from using unisotonic solution for rinsing. Second, owing to the nonwicking property of the blood cells on the hydrophobic nitrocellulose fibers, we employed another diagnostic criterion and investigated nitrocellulose blood-typing prototypes. The nitrocellulose blood-typing kit provides more simple, sensitive and trustworthy assay for rapid blood typing in situations with no access to laboratory facilities.

Objective Compliance and viscoelastic mismatches of small diameter vascular conduits and host arteries have been the cause of conduit’s failure. Methods To reduce these mismatches, the aim of this study was to develop and characterize a polyurethane conduit, which mimics the viscoelastic behaviors of human arteries. Electrospinning technique was used to fabricate tubular polyurethane conduits with similar properties of the human common carotid artery. This was achieved by manipulating the fiber diameter by altering the syringe flow rate of the solution. The mechanical and viscoelastic properties of the fabricated electrospun polyurethane conduits were, then, compared with commercially available vascular conduits, expanded polytetrafluoroethylene, polyethylene terephthalate (Dacron®) and the healthy human common carotid arteries. In addition, a comprehensive constitutive model was proposed to capture the visco-hyperelastic behavior of the synthetic electrospun polyurethanes, commercial conduits and human common carotid arteries. Results Results showed that increasing the fiber diameter of electrospun polyurethanes from 114 to 190 nm reduced Young’s modulus from 8 to 2 MPa. Also, thicker fiber diameter yielded in higher conduits’ viscosity. Furthermore, the results revealed that proposed visco-hyperelastic model is strongly able to fit the experimental data with great precision which proofs the reliability of the proposed model to address both nonlinear elasticity and viscoelasticity of the electrospun polyurethanes, commercial conduits and human common carotid arteries. Conclusions In conclusion, statistical analysis revealed that the elastic and viscous properties of 190 nm fiber diameter conduit are very similar to that of human common carotid artery in comparison to the commercial expanded polytetrafluoroethylene and Dacron® that are up to nine and seven times stiffer than natural vessels. Therefore, based on our findings, from the mechanical point of view, by considering the amount of Young’s modulus, compliance, distensibility and viscoelastic behavior, the fabricated electrospun polyurethane with fiber diameter of 189.6 ± 52.89 nm is an optimum conduit with promising potential for substituting natural human vessels.