Over the last decades, several compliant contact force models have been proposed. However, no complete and systematic comparison has been done on these models, which provides information on their range of application and accuracy for use in different contact scenarios. Thus, the selection of an appropriate model for a given contact problem is still an important and challenging issue to be addressed. The Hertzian contact theory remains the foundation for almost all of the available force models, but by itself, it is not appropriate for most impacts in practice, due to the amount of energy dissipated during the impact. A good number of contact force models have been offered that augment the Hertzian law with a damping term to accommodate the energy loss during the impact process for small or moderate impact velocities. In this work, the main issues associated with the most common compliant contact force models of this type are analyzed. Results in terms of the dynamic simulations of multibody systems are presented, which allow for the comparison of the similarities and differences among the models considered.

No abstract

A new approach to model and analyze flexible spatial multibody systems with clearance of cylindrical joints is presented in this work. The flexible parts are modeled by using absolute nodal coordinate formulation (ANCF)-based elements, while the rigid parts are described by employing the natural coordinate formulation (NCF), which can lead to a constant system mass matrix for the derived system equations of motion. In a simple way, a cylindrical joint with clearance is composed of two main elements, that is, a journal inside a bearing. Additionally, a lubricant fluid can exist between these two mechanical elements to reduce the friction and wear and increase the system's life. For the case in which the joint is modeled as a dry contact pair, a technique using a continuous approach for the evaluation of the contact force is applied, where the energy dissipation in the form of hysteresis damping is considered. Furthermore, the frictional forces developed in those contacts are evaluated by using a modified Coulomb's friction law. For the lubricated case, the hydrodynamic theory for dynamically loaded journal bearings is used to compute the forces generated by lubrication actions. The lubricated model is based on the Reynolds equation developed for the case of journal bearings with length-todiameter ratios up to 1. Using this approach, the misalignment of the journal inside the bearing can be studied. Finally, two demonstrative examples of application are used to provide results that support the discussion and show the validity of the proposed methodologies.

This paper presents and discusses the results obtained from a parametric study on the Baumgarte stabilization method for forward dynamics of constrained multibody systems. The main purpose of this work is to analyze the influence of the variables that affect the violation of constraints, chiefly the values of the Baumgarte parameters, the integration method, the time step, and the quality of the initial conditions for the positions. In the sequel of this process, the formulation of the rigid multibody systems is reviewed. The generalized Cartesian coordinates are selected as the variables to describe the bodies’ degrees of freedom. The formulation of the equations of motion uses the Newton–Euler approach, augmented with the constraint equations that lead to a set of differential algebraic equations. Furthermore, the main issues related to the stabilization of the violation of constraints based on the Baumgarte approach are revised. Special attention is also given to some techniques that help in the selection process of the values of the Baumgarte parameters, namely, those based on the Taylor’s series and the Laplace transform technique. Finally, a slider-crank mechanism with eccentricity is considered as an example of application in order to illustrate how the violation of constraints can be affected by different factors.

International audienceThe aim of this work is to develop a dynamic model for the biological human knee joint. The model is formulated in the framework of multibody systems methodologies, as a system of two bodies, the femur and the tibia. For the purpose of describing the formulation, the relative motion of the tibia with respect to the femur is considered. Due to their higher stiffness compared to that of the articular cartilages, the femur and tibia are considered as rigid bodies. The femur and tibia cartilages are considered to be deformable structures with specific material characteristics. The rotation and gliding motions of the tibia relative to the femur cannot be modeled with any conventional kinematic joint, but rather in terms of the action of the knee ligaments and potential contact between the bones. Based on medical imaging techniques, the femur and tibia profiles in the sagittal plane are extracted and used to define the interface geometric conditions for contact. When a contact is detected, a continuous nonlinear contact force law is applied which calculates the contact forces developed at the interface as a function of the relative indentation between the two bodies. The four basic cruciate and collateral ligaments present in the knee are also taken into account in the proposed knee joint model, which are modeled as nonlinear elastic springs. The forces produced in the ligaments, together with the contact forces, are introduced into the system's equations of motion as external forces. In addition, an external force is applied on the center of mass of the tibia, in order to actuate the system mimicking a normal gait motion. Finally, numerical results obtained from computational simulations are used to address the assumptions and procedures adopted in this study

In this work a comprehensive methodology for dynamic modeling and analysis of planar multibody systems with lubricated revolute joints is presented. In general, this type of mechanical systems includes journal-bearings in which the load varies in both magnitude and direction. The fundamental issues associated with the theory of lubrication for dynamically loaded journal-bearings are revisited that allow for the evaluation of the Reynolds' equation for dynamic regime. This approach permits the derivation of the suitable hydrodynamic force laws that are embedded into the dynamics of multibody systems formulation. In this work, three different hydrodynamic force models are considered, namely the Pinkus and Sternlicht approach for long journalbearings and the Frêne et al. models for both long and short journal-bearings. Results for a planar slider-crank mechanism with a lubricated revolute joint between the connecting-rod and slider are presented and utilized to discuss the assumptions and procedures adopted throughout the present study. Different test scenarios are taken into account with the purpose of performing a comparative study for quantifying the influence of the clearance size, lubricant viscosity, input crank speed and hydrodynamic force model on the dynamic response of multibody systems with lubricated revolute joints. From the global results obtained from computational simulations, it can be concluded that the clearance size, the lubricant viscosity and the operating conditions play a key role in predicting the dynamic behavior of multibody systems.

This research focuses on the definition and application of a characterization methodology to determine the characteristics of fused deposition modeling 3D printing materials. Commercial short fiber reinforced and unreinforced polyethylene terephthalate glycol parts were tested achieving comparison terms. The presented methodology is composed of three classes: thermal analysis, mechanical testing, and material morphology. Filament was tensile tested with specially developed setup for determining the mechanical properties of raw materials. Standardized flexural and tensile samples were printed 100% dense in both materials and tested. Differential scanning calorimetry results showed that the thermal properties of both materials do not change with successive heating cycles. Thermogravimetric analysis allowed to understand the thermal stability of materials and quantify the amount of fiber in the matrix. Tensile tests indicated that the addition of fibers increases the Young’s modulus by 70.10% but there is lesser withstanding of stress by 28.21%. Flexural tests exhibited an increase in flexural modulus of 191.38% and 5.14% in flexural strength for the reinforced polyethylene terephthalate glycol, due to the presence of fiber. Microscopic analysis revealed a 12% of void spots and fiber alignment accordingly to the deposition path.

Surfaces of poly(L-lactic acid) (PLLA) of well-defined microtopography were prepared by making use of the semicrystalline character of PLLA. Different thermal treatments before isothermal crystallization (which include nucleation steps) permit to obtain a controlled number of simultaneously growing spherulites, which, in the end, modulate the topography at the microscale. Four qualitatively different surfaces were prepared. The dynamics of primary human chondrocyte adhesion and cytoskeleton organization was investigated on the different surfaces. Chondrocyte morphology is shown to be influenced by the microtopography of the system as obtained by scanning electron microscopy and atomic force microscopy (AFM). The cytoplasmatic distribution of a focal adhesion protein, tensin, is followed as a function of time. Since the effect of surface topography on cell morphology is a consequence of the process of interaction between the extracellular matrix (ECM) proteins, adsorbed on the surface of the material, and related cell adhesion molecules, the conformation of one ECM protein, fibronectin, adsorbed on the different substrates was investigated by means of AFM.