The dynamic analysis of planar multibody systems with revolute clearance joints, including dry contact and lubrication effects is presented here. The clearances are always present in the kinematic joints. They are known to be the sources for impact forces, which ultimately result in wear and tear of the joints. A joint with clearance is included in the multibody system much like a revolute joint. If there is no lubricant in the joint, impacts occur in the system and the corresponding impulsive forces are transmitted throughout the multibody system. These impacts and the eventual continuous contact are described here by a force model that accounts for the geometric and material characteristics of the journal and bearing. In most of the machines and mechanisms, the joints are designed to operate with some lubricant fluid. The high pressures generated in the lubricant fluid act to keep the journal and the bearing surfaces apart. Moreover, the lubricant provides protection against wear and tear. The equations governing the dynamical behavior of the general mechanical systems incorporate the impact force due to the joint clearance without lubricant, as well as the hydrodynamic forces owing to the lubrication effect. A continuous contact model provides the intra-joint impact forces. The friction effects due to the contact in the joints are also represented. In addition, a general methodology for modeling lubricated revolute joints in multibody mechanical systems is also presented. Results for a slider-crank mechanism with a revolute clearance joint between the connecting rod and the slider are presented and used to discuss the assumptions and procedures adopted.

No abstract

In this work a methodology for the dynamical analysis of mechanical systems considering realistic joint characteristics, namely, joints with clearance and lubrication is presented. For the case of the joints with clearance modelled as a contact pair with dry contact, a technique using a continuous approach for the evaluation of the contact force is applied, in which the energy dissipation in form of hysteresis damping is considered. The friction forces are calculated using a modified CoulombÕs friction law. For the lubricated case, the hydrodynamic theory for dynamically loaded journal-bearings is used to compute the forces generated by lubrication action. The numerical results point out that the existence of dry joint clearances causes high peaks on the kinematic and dynamic systemÕs characteristics due to contact-impact forces when compared to those obtained with lubricated model. The performance of the lubricated joint is closer to that of an ideal joint.

A comprehensive combined numerical and experimental study on the dynamic response of a slider-crank mechanism with revolute clearance joints is presented and discussed in this paper to provide an experimental verification and validation of the predictive capabilities of the multibody clearance joint models. This study is supported in an experimental work in a test rig, which consists of a slider-crank mechanism with an adjustable radial clearance at the revolute joint between the slider and the connecting rod. The motion of the slider is measured with a linear transducer and an accelerometer.Dynamic tests at different operating crank speeds and with several clearance sizes are performed. The maximum slider acceleration, associated with the impact acceleration, is used as a measure of the impact severity. The obtained results demonstrate the dynamical behavior of a multibody mechanical system with a clearance joint. Finally, the correlation between the numerical and experimental results is presented and discussed leading to validated models of clearance revolute joints.

This work deals with contact -impact force models for both spherical and cylindrical contact surfaces. The incorporation of the friction phenomenon, based on the Coulomb friction law, is also discussed together with an effective computational strategy, which includes the automatic step size selection procedure. Impacts within a revolute clearance joint in a basic slider -crank mechanism are used as an example to compare the different contact force models. The collision is a prominent phenomenon in many multi-body systems such as mechanisms with intermittent motion, kinematic discontinuities, and clearance joints. As a result of an impact, the values of the system state variables change very fast, eventually looking like discontinuities in the system velocities and accelerations. The impact is characterized by large forces that are applied and removed in a short time period. The knowledge of the peak forces developed in the impact process is very important for the dynamic analysis of multibody systems and it has consequences in the design process. The model for the contactimpact force must consider the material and geometric properties of the colliding surfaces, consider information on the impact velocity, contribute to an efficient integration, and account for some level of energy dissipation. These characteristics are ensured with a continuous contact force model, in which the deformation and contact forces are considered as continuous functions.

This paper deals with a general methodology to assess the influence of the clearance size and the friction coefficient on the dynamic response of planar rigid multi-body systems including revolute joints with clearance. When there is a clearance in a revolute joint, impacts between the journal and the bearing can occur, and consequently, local deformations take place. The impact is internal and the response of the system is performed using a continuous contact force model. The friction effect because of the contact between joint elements is also included. The dynamic response of the systems is obtained numerically by solving the constraint equations and the contact-impact forces produced in the clearance joint, simultaneously with the differential equations of motion and a set of initial conditions. Numerical results for two simple mechanisms with revolute clearance joints are presented and discussed. In the present work, the clearance size and friction effects are analysed separately. Through the use of Poincaré maps, both periodic and chaotic responses of the systems are observed. The results predict the existence of the periodic or regular motion at certain clearance sizes and friction coefficients and chaotic or non-linear in other cases.

The main purpose of this work is to present a general methodology for modeling lubricated revolute joints in constrained rigid multibody systems. In the dynamic analysis of journal-bearings, the hydrodynamic forces, which include both squeeze and wedge effects, generated by the lubricant fluid, oppose the journal motion. The hydrodynamic forces are obtained by integrating the pressure distribution evaluated with the aid of Reynolds' equation, written for the dynamic regime. The hydrodynamic forces built up by the lubricant fluid are evaluated from the system state variables and included into the equations of motion of the multibody system. Numerical examples are presented in order to demonstrate the use of the methodologies and procedures described in this work.

International audienceThe aim of this work is to develop a dynamic model for the biological human knee joint. The model is formulated in the framework of multibody systems methodologies, as a system of two bodies, the femur and the tibia. For the purpose of describing the formulation, the relative motion of the tibia with respect to the femur is considered. Due to their higher stiffness compared to that of the articular cartilages, the femur and tibia are considered as rigid bodies. The femur and tibia cartilages are considered to be deformable structures with specific material characteristics. The rotation and gliding motions of the tibia relative to the femur cannot be modeled with any conventional kinematic joint, but rather in terms of the action of the knee ligaments and potential contact between the bones. Based on medical imaging techniques, the femur and tibia profiles in the sagittal plane are extracted and used to define the interface geometric conditions for contact. When a contact is detected, a continuous nonlinear contact force law is applied which calculates the contact forces developed at the interface as a function of the relative indentation between the two bodies. The four basic cruciate and collateral ligaments present in the knee are also taken into account in the proposed knee joint model, which are modeled as nonlinear elastic springs. The forces produced in the ligaments, together with the contact forces, are introduced into the system's equations of motion as external forces. In addition, an external force is applied on the center of mass of the tibia, in order to actuate the system mimicking a normal gait motion. Finally, numerical results obtained from computational simulations are used to address the assumptions and procedures adopted in this study