Seiring dengan perkembangan peradaban manusia, tingkat kebutuhan energi juga semakin meningkat. Pemenuhan energi dewasa ini masih didominasi oleh pembakaran bahan bakar fosil sedangkan energi yang berasal dari energi terbarukan masih terabaikan. Pembangkit listrik tenaga angin merupakan salah pembangkit listrik yang menggunakan sumber energi terbarukan yang banyak digunakan, karena sifat energi angin yang ramah lingkungan serta mudah dalam melakukan pengoperasian. Indonesia saat ini sedang mengalami krisis energi listrik karena kebutuhan energi listrik yang semakin besar akibat adanya pertumbuhan industri, peningkatan jumlah pemakaian alat elektronik rumah tangga, perkembangan teknologi dan komunikasi, dan sebagainya. Aceh barat merupakan salah satu kabupaten yang terletak di Aceh dengan ibukota bernama Meulaboh. Aceh barat mempunyai letak menurut garis lintang dan bujur yaitu 04006’-04047’ Lintang Utara dan 95052’-96030’ Bujur Timur, dengan luas daerah 2.927,95 Km2 dan mempunyai 12 kecamatan serta 321 kampung. Penelitian ini dilakukan bertujuan untuk menghasilkan analisis mawar angin sebagai dasar prediksi daya angin dikota Meulaboh. Dari analisis didapatkan bahwa Mawar Angin tersebut memperlihatkan distribusi energi angin selama kurun waktu setahun dalam arah 3600. Arah angin maksimum terjadi pada arah 3000 dan distribusi terendah terjadi pada arah 800.
Road lighting is important for transportation activities, especially at night. The design of this Hybrid plant has a working principle that is utilizing wind gusts from a passing vehicle to turn the turbine blade and the heat of solar radiation that is absorbed through the solar panel with the sun tracking system. Parameter data that influence in the design of Hybrid Generations are variations in the number of turbine blades, turbine angle, wind speed, turbine drive rotor height, density of air and heat of solar radiation. The purpose of the problem in Designing Hybrid VAWT generating systems with the optimal angle of the turbine and Solar Cell automatically to be able to meet the electrical energy requirements for street lighting. The research method used in design through three stages, namely literature review, Technical Design and preparation of work tools and materials. The design results show that the optimal type u vertical wind turbine for toll road lighting with 3 blades and an optimal angle size of 90 0C, rotor diameter of 400 mm, rotor height of 1000 mm for average wind speed of 13.9 m / s. and Average solar heat of 28 0C with an average panel temperature of 55.3 0C using the Timer switch as a solar tracking system. The design of the plant, produces turbine power of 0.93 V to 1.17 V at 122 rpm to 214 rpm. And the solar panel produces a panel voltage of 19.59 V and an average voltage on the battery of 14 V. The stored electrical energy is able to light two LED lights with a power of 15 Watt and last for 12 hours / dayKeywords— Hybrid Power Generation, Optimal Angle, Timer Switch
Drying chamber is a drying application for agriculture product to produce high quality and hygiene product. The purpose of this paper is to propose best configuration trays arrangement in drying chamber for better distribution of velocity and temperature. Therefore, five configurations of trays are analyzed to obtain the best performance of uniformity air flow distribution within drying chamber. CFD simulation studied the uniform air flow in the drying chamber in steady state condition. A validation is performed by comparing the data obtained from the literature review CFD simulation to ensure the methodology is correct. Then, the drying chamber with different trays arrangements are simulated using CFD simulations to obtain velocity and temperature distributions at nine plotted points on trays. From the results obtained, it concluded that design (A) and (D) are selected as the best designs for uniformity because there is less discrepancy for each point contributed the more uniformity of distribution.
Mesin Penyangrai kelapa kukur (U Neuleu) adalah mesin yang digunakan untuk melakukan proses sangrai dengan cara penggorengan tanpa menggunakan minyak dan tangan manusia. Desain alat akan menjelaskan bagaimana proses menggambar bagian-bagian dari alat yang akan di rancangan oleh karna itu perlu persiapan yang matang untung mendesain suatu alat agar waktu proses pembuatan nya tidak akan terjadi kesalahan dimana nanti nya waktu pembuatan alat harus sesuai dengan gambar yang sudah di buat sebelumnya. Mesin sangrai ini bekerja secara Otomatis yang di kontrol mengunakan Adruino UNO untuk Rangkaian elektrikal menggunakan arduino untuk bisa mengatur waktu matinya motor DC saat melakukan penyangraian, pengontrolan waktu menghidupkan alat penyangrai sebagai otomasi yang mengurangi ketergantungan dari kontrol operator, bisa dilakukan dengan pengaturan waktu penyangrai sesuai dengan kematangan U Neuleu. Kata kunci: mesin pneumatic power forging hammer, analisa kekuatan rangka, autodesk inventor 2017.
Energi merupakan salah satu kebutuhan utama dalam kehidupan manusia. Pengembangan PLTB (Pembangkit Listrik Tenaga Bayu) pada kawasan kampus Univ. Teuku Umar perlu diteliti, mengingat kapasitas dan potensi energi angin yang tersedia. Berdasarkan analisa diatas, maka perlu dilakukan penelitian tentang rancang bangun turbin angin skala kecil untuk kawasan kampus Univ. Teuku Umar. Penelitian ini dilaksanakan dan berlokasi di workshop Teknik Mesin Universitas Teuku Umar, Meulaboh. Desain pembangkit listrik tenaga angin tipe horizontal menggunakan software skethup pro 2016 dan AutoCAD. Beberapa data ditentukan sebagai dasar untuk merancang turbin angin sumbu horizontal di antaranya daya (????), tinggi hub, jumlah sudu, tip speed ratio (????), koefisien daya (Cp), penampang Airfoil. Setiap jenis airfoil memiliki nilai drag, lift, dan sudut serang yang berbeda. Perakitan pembangkit listrik tipe horizontal ini dilakukan dengan tahapan yaitu: memasang semua komponen pada turbin angin seperti: kerangka, rumah turbin, generator, mekanisme yaw, dan hub.
This study aims to look at the performance of the solar water heater collector with the addition of a reflector. Reflector is used to increase the absorption of solar radiation. The test was carried out by varying the water flow rate in the pipe, namely 75 l/hour, 150 l/hour and 225 l/hour with a collector tilt angle of 30°. Tests are carried out every one hour, starting at 09.00-16.00 WIB for each variation. Parameters measured in this study included glass temperature, inlet water temperature, outlet water temperature, pipe temperature, absorber temperature, ambient temperature and wind speed. The results showed that the highest efficiency occurred at a flow rate of 225 l/hour, which was 62.44% at IT 3,366 MJ/m2, and the highest ratio of outlet water temperature and inlet water temperature was 1.51 at a flow rate of 75l/h. Adding a reflector to the coverslip can increase collector efficiency.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.