This paper reviews energy storage systems, in general, and for specific applications in low-cost micro-energy harvesting (MEH) systems, low-cost microelectronic devices, and wireless sensor networks (WSNs). With the development of electronic gadgets, low-cost microelectronic devices and WSNs, the need for an efficient, light and reliable energy storage device is increased. The current energy storage systems (ESS) have the disadvantages of self-discharging, energy density, life cycles, and cost. The ambient energy resources are the best option as an energy source, but the main challenge in harvesting energy from ambient sources is the instability of the source of energy. Due to the explosion of lithium batteries in many cases, and the pros associated with them, the design of an efficient device, which is more reliable and efficient than conventional batteries, is important. This review paper focused on the issues of the reliability and performance of electrical ESS, and, especially, discussed the technical challenges and suggested solutions for ESS (batteries, supercapacitors, and for a hybrid combination of supercapacitors and batteries) in detail. Nowadays, the main market of batteries is WSNs, but in the last decade, the world’s attention has turned toward supercapacitors as a good alternative of batteries. The main advantages of supercapacitors are their light weight, volume, greater life cycle, turbo charging/discharging, high energy density and power density, low cost, easy maintenance, and no pollution. This study reviews supercapacitors as a better alternative of batteries in low-cost electronic devices, WSNs, and MEH systems.
Herein, we report thin films’ characterizations and photovoltaic properties of an organic semiconductor zinc phthalocyanine (ZnPc). To study the former, a 100 nm thick film of ZnPc is thermally deposited on quartz glass by using vacuum thermal evaporator at 1.5 × 10−6 mbar. Surface features of the ZnPc film are studied by using scanning electron microscope (SEM) with in situ energy dispersive x-ray spectroscopy (EDS) analysis and atomic force microscope (AFM) which reveal uniform film growth, grain sizes and shapes with slight random distribution of the grains. Ultraviolet-visible (UV-vis) and Fourier Transform Infrared (FTIR) spectroscopies are carried out of the ZnPc thin films to measure its optical bandgap (1.55 eV and 3.08 eV) as well as to study chemical composition and bond-dynamics. To explore photovoltaic properties of ZnPc, an Ag/ZnPc/PEDOT:PSS/ITO cell is fabricated by spin coating a 20 nm thick film of hole transport layer (HTL)—poly-(3,4-ethylenedioxythiophene) poly(styrene sulfonic acid) (PEDOT:PSS)—on indium tin oxide (ITO) substrate followed by thermal evaporation of a 100 nm layer of ZnPc and 50 nm silver (Ag) electrode. Current-voltage (I-V) properties of the fabricated device are measured in dark as well as under illumination at standard testing conditions (STC), i.e., 300 K, 100 mW/cm2 and 1.5 AM global by using solar simulator. The key device parameters such as ideality factor (n), barrier height ( ϕ b ), junction/interfacial resistance (Rs) and forward current rectification of the device are measured in the dark which exhibit the formation of depletion region. The Ag/ZnPc/PEDOT:PSS/ITO device demonstrates good photovoltaic characteristics by offering 0.48 fill factor (FF) and 1.28 ± 0.05% power conversion efficiency (PCE), η.
Recently, electric vehicle (EV) technology has received massive attention worldwide due to its improved performance efficiency and significant contributions to addressing carbon emission problems. In line with that, EVs could play a vital role in achieving sustainable development goals (SDGs). However, EVs face some challenges such as battery health degradation, battery management complexities, power electronics integration, and appropriate charging strategies. Therefore, further investigation is essential to select appropriate battery storage and management system, technologies, algorithms, controllers, and optimization schemes. Although numerous studies have been carried out on EV technology, the state-of-the-art technology, progress, limitations, and their impacts on achieving SDGs have not yet been examined. Hence, this review paper comprehensively and critically describes the various technological advancements of EVs, focusing on key aspects such as storage technology, battery management system, power electronics technology, charging strategies, methods, algorithms, and optimizations. Moreover, numerous open issues, challenges, and concerns are discussed to identify the existing research gaps. Furthermore, this paper develops the relationship between EVs benefits and SDGs concerning social, economic, and environmental impacts. The analysis reveals that EVs have a substantial influence on various goals of sustainable development, such as affordable and clean energy, sustainable cities and communities, industry, economic growth, and climate actions. Lastly, this review delivers fruitful and effective suggestions for future enhancement of EV technology that would be beneficial to the EV engineers and industrialists to develop efficient battery storage, charging approaches, converters, controllers, and optimizations toward targeting SDGs.
The demand for power is increasing due to the rapid growth of the population. Therefore, energy harvesting (EH) from ambient sources has become popular. The reduction of power consumption in modern wireless systems provides a basis for the replacement of batteries with the electromagnetic energy harvesting (EMEH) approach. This study presents a general review of the EMEH techniques for autonomous sensor (ATS) applications. Electromagnetic devices show great potential when used to power such ATS technologies or convert mechanical energy to electrical energy. As its power source, this stage harvests ambient energy and features a self-starting and self-powered process without the use of batteries. Therefore, it consumes low power and is highly stable for harvesting energy from the environment with low ambient energy sources. The review highlights EMEH circuits, low power EMEH devices, power electronic converters, and controllers utilized in numerous applications, and described their impacts on energy conservation, benefits, and limitation. This study ultimately aims to suggest a smart, low-voltage electronic circuit for a low-power sensor that harvests electromagnetic energy. This review also focuses on various issues and suggestions of future EMEH for low power autonomous sensors.
This paper reports the potential application of cadmium selenide (CdSe) quantum dots (QDs) in improving the microelectronic characteristics of Schottky barrier diode (SBD) prepared from a semiconducting material poly-(9,9-dioctylfluorene) (F8). Two SBDs, Ag/F8/P3HT/ITO and Ag/F8-CdSe QDs/P3HT/ITO, are fabricated by spin coating a 10 wt% solution of F8 in chloroform and 10:1 wt% solution of F8:CdSe QDs, respectively, on a pre-deposited poly(3-hexylthiophene) (P3HT) on indium tin oxide (ITO) substrate. To study the electronic properties of the fabricated devices, current-voltage (I-V) measurements are carried out at 25 °C in dark conditions. The I-V curves of Ag/F8/P3HT/ITO and Ag/F8-CdSe QDs/P3HT/ITO SBDs demonstrate asymmetrical behavior with forward bias current rectification ratio (RR) of 7.42 ± 0.02 and 142 ± 0.02, respectively, at ± 3.5 V which confirm the formation of depletion region. Other key parameters which govern microelectronic properties of the fabricated devices such as charge carrier mobility (µ), barrier height (φ b ), series resistance (R s ) and quality factor (n) are extracted from their corresponding I-V characteristics. Norde's and Cheung functions are also applied to characterize the devices to study consistency in various parameters. Significant improvement is found in the values of R s , n, and RR by 3, 1.7, and 19 times, respectively, for Ag/F8-CdSe QDs/P3HT/ ITO SBD as compared to Ag/F8/P3HT/ITO. This enhancement is due to the incorporation of CdSe QDs having 3-dimensional quantum confinement and large surface-to-volume area. Poole-Frenkle and Richardson-Schottky conduction mechanisms are also discussed for both of the devices. Morphology, optical bandgap (1.88 ± 0.5 eV) and photoluminescence (PL) spectrum of CdSe QDs with a peak intensity at 556 nm are also reported and discussed.Junction between different materials has a vital role in electronic and optoelectronic devices and is, therefore, one of the significant parts that govern the performance of a device. Well-controlled and easily tunable interfacial properties are always desirable in many electronic and optoelectronic devices. Among different types of junctions in devices, metal-semiconductor (MS) structures provide their role in the form of Schottky barrier diodes (SBDs) 1 . SBDs play a central role in the device functioning 2 as well as is the most widely used type of junctions in semiconductor devices 3 , solar cells 4 and field effect transistors (FETs) 5 . Mostly, commercially available electronic devices are based on inorganic semiconductors due to their high stability and performance 6 . However, due to high cost, high temperature complex processability and mechanical brittleness, inorganic semiconductors are not favorable. On the other hand, organic semiconducting materials are rich in pi-conjugated structures and have gained remarkable attention due to overcoming the issues with inorganic semiconductors. Organic semiconductors offer low temperature processability, low cost, mechanical flexibility, simple methods for devi...
In this paper, we report on the synthesis—via the wet chemical precipitation route method—and thin film characteristics of inorganic semiconductor, cuprous oxide (Cu2O) nanoparticles, for their potential application in enhancing the humidity-sensing properties of semiconducting polymer poly(9,9-dioctylfluorene) (F8). For morphological analysis of the synthesized Cu2O nanoparticles, transmission electron microscope (TEM) and scanning electron microscope (SEM) micrographs are studied to investigate the texture, distribution, shape, and sizes of Cu2O crystallites. The TEM image of the Cu2O nanoparticles exhibits somewhat non-uniform distribution with almost uniform shape and size having an average particle size of ≈24 ± 2 nm. Fourier transformed infrared (FTIR) and X-ray diffraction (XRD) spectra are studied to validate the formation of Cu2O nanoparticles. Additionally, atomic force microscopy (AFM) is performed to analyze the surface morphology of polymer-inorganic (F8-Cu2O) nanocomposites thin film to see the grain sizes, mosaics, and average surface roughness. In order to study the enhancement in sensing properties of F8, a hybrid organic–inorganic (F8-Cu2O) surface-type humidity sensor Ag/F8-Cu2O/Ag is fabricated by employing F8 polymer as an active matrix layer and Cu2O nanoparticles as a dopant. The Ag/F8-Cu2O/Ag device is prepared by spin coating a 10:1 wt% solution of F8-Cu2O nanocomposite on pre-patterned silver (Ag) electrodes on glass. The inter-electrode gap (≈5 μm) between Ag is developed by photolithography. To study humidity sensing, the Ag/F8-Cu2O/Ag device is characterized by measuring its capacitance (C) as a function of relative humidity (%RH) at two different frequencies (120 Hz and 1 kHz). The device exhibits a broad humidity sensing range (27–86%RH) with shorter response time and recovery time, i.e., 9 s and 8 s, respectively. The present results show significant enhancement in the humidity-sensing properties as compared to our previously reported results of Ag/F8/Ag sensor wherein the humidity sensing range was 45–78%RH with 15 s and 7 s response and recovery times, respectively. The improvement in the humidity-sensing properties is attributed to the potential use of Cu2O nanoparticles, which change the hydrophobicity, surface to volume ratio of Cu2O nanoparticles, as well as modification in electron polarizability and polarity of the F8 matrix layer.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.