Summary:Rapid prototyping models (RPMs) had been extensively used in craniofacial and maxillofacial surgery, especially in areas such as orthognathic surgery, posttraumatic or oncological reconstructions, and implantology. Economic limitations are higher in developing countries such as Mexico, where resources dedicated to health care are limited, therefore limiting the use of RPM to few selected centers. This article aims to determine the dimensional error of a low-cost fused deposition modeling 3D printer (Tronxy P802MA, Shenzhen, Tronxy Technology Co), with Open source software. An ordinary dry human mandible was scanned with a computed tomography device. The data were processed with open software to build a rapid prototype with a fused deposition machine. Linear measurements were performed to find the mean absolute and relative difference. The mean absolute and relative difference was 0.65 mm and 1.96%, respectively (P = 0.96). Low-cost FDM machines and Open Source Software are excellent options to manufacture RPM, with the benefit of low cost and a similar relative error than other more expensive technologies.
ResumenObjetivo: Presentar nuestra experiencia en el diagnóstico y el tratamiento de 42 pacientes con síndrome de Goldenhar. Método: Se realizó un estudio descriptivo, observacional y retrospectivo usando el registro médico y fotográfico de todos los pacientes diagnosticados con síndrome de Goldenhar tratados por la unidad de cirugía craneofacial del departamento de cirugía plástica y reconstructiva del hospital Dr. Manuel Gea González entre 2010 y 2018. Resultados: Se obtuvieron 42 pacientes, el 54% varones, con predominio de menores de 10 años (57%), de los cuales todos se sometieron al menos a un procedimiento. Los procedimientos quirúrgicos se dividieron en: 14 auriculares (20%), 17 mandibulares (24%), 2 Lefort (4%), 10 volumen (14%), 9 macrostoma (13%) y 16 otros (21%). En total se realizaron 71 procedimientos. Conclusión: El síndrome de Goldenhar es una enfermedad poco frecuente que afecta diversas estructuras y se presenta predominantemente en varones. Es necesario un diagnóstico precoz y un manejo individualizado llevado a cabo por un equipo multidisciplinario encabezado por cirujanos plásticos.
ResumenAntecedentes: Las heridas por mordedura de perro constituyen un problema de salud pública creciente que involucra a todos los niveles de atención. Pueden variar en gravedad, desde heridas superficiales (piel y tejido subcutáneo) hasta desvitalización y pérdida de tejidos, con presencia de infecciones, complicaciones y secuelas estéticas y funcionales que requieren tratamiento especializado. Objetivo: Describir la experiencia de 7 años en el manejo de heridas por mordedura de perro y proponer un algoritmo de manejo en un centro de referencia en cirugía plástica y reconstructiva en México. Método: Se realizó un estudio retrospectivo en el que se incluyeron todos los registros de pacientes con heridas por mordedura de perro entre julio de 2010 y agosto de 2017. Las variables recabadas fueron edad, sexo, localización anatómica, características de la herida y manejo terapéutico. Resultados: Se obtuvo un total de 416 pacientes. El 63% de las lesiones ocurrieron en menores de 18 años. La mayoría de las heridas (88.2%) fueron aisladas en una región anatómica. La localización más frecuente fue la cara (61.3%). De todos los casos, el 74.3% se resolvieron solo con cierre primario, el 21.4% requirió además algún proceso reconstructivo, el 2.9% no requirió cierre y el 1.4% de los pacientes fueron hospitalizados. Todos los pacientes recibieron antibióticos profilácticos. El 2% reportaron infección posterior al manejo con cierre primario. Conclusiones: El correcto abordaje de las heridas por mordedura de perro en todos los niveles de atención mejora el pronóstico de los pacientes. Las heridas complejas deben ser manejadas inmediatamente en un centro de segundo o tercer nivel con cirugía plástica y reconstructiva. La mayoría de las heridas por mordedura de perro pueden ser reparadas con cierre primario y otras técnicas reconstructivas con seguridad.
Mandibular distraction osteogenesis (MDO) is a fairly common procedure in specialized craniofacial surgery centers. The MDO is a minimally invasive technique that is able to generate new bone in patients with a severe hypoplastic ascending ramus, while also expanding the overlying soft tissues; therefore, it has become the treatment of choice for the surgical correction of mandibular hypoplasias. One of the most common postoperative complications involves misplacement of the distractor and/or corticotomy, which can result in the creation of an erroneous distraction vector. The introduction of 3-dimensional (3D) printing has revolutionized preoperative planning in several surgical fields; however, cost can hinder its application in developing nations, specially in public institutions. The aim of this work is present our experience using low-cost 3D-printed anatomic models for preoperative planning and surgical simulation in patients requiring MDO.
Authors presented the case of a 4-year-old male patient who suffered a dog bite on his face with partial amputation of the nasal tip, managed at another institution conservatively, so that one year after the injury he came for the nasal deformity. A frontal flap was performed for reconstruction achieving excellent results, coverage was achieved with similar characteristics of the skin as color and texture. The patient had a follow-up of 5 years with an appropriate course. Authors presented the case due to few reports in the literature of its use in children, where it can be observed that it is an excellent reconstructive tool.
Background: Dog bites continue to be a frequent cause for plastic and reconstructive services in the world. The grand majority of these cases affect the head and neck area; and more often than not they involve the commissure and the lips. The latter leading to an increased level of difficulty and a substantial decrease on the posibilities for a successful reconstruction. This case report focuses on the exploration of the Abbe-Estlander flap as an efficient alternative in most of these cases.Methods: We present two clinical cases involving dog bites where the affected area of both patients was estimated to be one third of the total volume of the lip. Both patients required emergency reconstructive surgery. An Estlander flap was successfully performed in both instances. The purpose of the article is to share the results and motivate the medical community to continue to use this method as a strong avenue for an effective recovery.Results: After two months of the surgery, the team followed up with both patients and they were satisfied with the results. Patient A presented adequate healing of the wound; a lack of alignment of the mucocutaneous rim and rounding of the commissure was observed. Phonation, oral continence without any leakage and complete closure of the lip were also part of the recovery assessment. Patient B presented adequate healing of the wound, phonation and medium oral continence with occasional leakage of liquids and incomplete closure.Conclusions: The Abbe-Estlander flap is still an excellent reconstructive alternative for upper and lower lip reconstruction where the affected area is up to one third of the total volume. As long as the commissure involvement represents minimum difficulty, both aesthetic and functional objectives can be successfully attained using this flap.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.