Summary:Rapid prototyping models (RPMs) had been extensively used in craniofacial and maxillofacial surgery, especially in areas such as orthognathic surgery, posttraumatic or oncological reconstructions, and implantology. Economic limitations are higher in developing countries such as Mexico, where resources dedicated to health care are limited, therefore limiting the use of RPM to few selected centers. This article aims to determine the dimensional error of a low-cost fused deposition modeling 3D printer (Tronxy P802MA, Shenzhen, Tronxy Technology Co), with Open source software. An ordinary dry human mandible was scanned with a computed tomography device. The data were processed with open software to build a rapid prototype with a fused deposition machine. Linear measurements were performed to find the mean absolute and relative difference. The mean absolute and relative difference was 0.65 mm and 1.96%, respectively (P = 0.96). Low-cost FDM machines and Open Source Software are excellent options to manufacture RPM, with the benefit of low cost and a similar relative error than other more expensive technologies.

No abstract

Background: Since the description of superficial fascia flap harvesting, a new window of opportunity has been open in obese patients, where a higher subcutaneous thickness of tissue is present. To our knowledge, the impact of body mass index on superficial fascial flaps has not been reported. Methods: We recruited 122 patients from April 2019 to January 2020. From these patients, the 3 most common thinned flaps were selected: the superficial circumflex iliac perforator flap; the anterolateral thigh flap at the perforator A, B, and C; and the thoracodorsal flap. Two vertical measures were registered: the distance from the skin to the superficial fascia, and from this point to the deep fascia. Results: The average flap measurement presented here was within the range, as previous clinical studies. The superficial fatty layer thickness in the superficial circumflex iliac perforator and anterolateral thigh flap was somewhat similar in thickness between overweight and obese patients, showing a minimal increase with higher body mass index. The anterolateral thigh flap was found thicker among women, and no statistical difference was shown between age groups in any of the flaps. Conclusions: A better understanding of the fat layers’ thickness will result in better planning, minimizing secondary debulking procedures, decreasing operative time, and reducing general complications among obese patients. Thus, a better understanding of flap structure and physiology in obese patients will lower complications and give more predictable results.

La impresión 3D es una tecnología interesante en constante evolución. También conocida como manufactura aditiva, consiste en la conversión de diseños digitales a modelos físicos mediante la adición de capas sucesivas de material. En años recientes, y tras el vencimiento de múltiples patentes, diversos campos de las ciencias de la salud se han interesado en sus posibles usos, siendo la cirugía plástica una de las especialidades médicas que más ha aprovechado sus ventajas y aplicaciones, en especial la capacidad de crear dispositivos altamente personalizados a costos accesibles. Teniendo en cuenta lo anterior, el objetivo del presente artículo es describir los usos de la impresión 3D en cirugía plástica reconstructiva a partir de una revisión de la literatura.Las principales aplicaciones de la impresión 3D descritas en la literatura incluyen su capacidad para crear modelos anatómicos basados en estudios de imagen de pacientes, que a su vez permiten planificar procedimientos quirúrgicos, fabricar implantes y prótesis personalizadas, crear instrumental quirúrgico para usos específicos y usar biotintas en ingeniería tisular.La impresión 3D es una tecnología prometedora con el potencial de implementar cambios positivos en la práctica de la cirugía plástica reconstructiva en el corto y mediano plazo.

Introduction:The incidence of facial bones fractures is 18 to 32 for each 100,000 inhabitants. The most affected population are young working people. Fractures are most commonly caused by assaults and motor vehicle accidents. Its cost of care reaches 1.06 billion dollars. Premodeling osteosynthesis plates with anatomical models can decrease surgical time, bleeding, and increase patient satisfaction. This study aims to evaluate the impact of premodeled osteosynthesis plates, using anatomical models in patients with facial fractures. Material and Methods: Patients with facial fractures treated by open reduction and internal fixation were included-Group A without premolding plates and Group B with premolding. The variables studied were: age, sex, etiology of the fractures, number of fractures, among other variables that reflect the quality of the results. Results: A total of 17 osteosynthesis plates were included in 6 patients. The age was 22 to 47 years; all patients were male. The maximum surgery time was 129 to 300 minutes. The average time to start work was 4.8 weeks. When comparing the variables between the groups, we found no difference between the groups for bleeding P ¼ 0.24, the start of work P ¼ 0.19, the time of surgery P ¼ 0.082, or for osteosynthesis time P ¼ 0.15. There was only a significant difference in patient satisfaction, P ¼ 0.04. Conclusions:The evidence collected shows that premodeling the plates only improves patients' satisfaction among facial fractures treated by open reduction and internal fixation.

HighlightsThe objective of this paper is to describe a patient undergoing with upper intestinal obstruction and a GPEH Type IV, approached laparoscopically.To describe actualized literature in GPEH and intestinal occlusion.Describe a technical difficult laparoscopic procedure.This paper adds to the literature a combined scenario of Giant hernia plus intestinal upper obstruction.Also we add, an actualized revision of literature.

Non-invasive medical treatment solves most cases. Promising results have been achieved with neostigmine. In the event of no response to drug therapy, the next step is endoscopic treatment. Even with high recurrence this is preferred due to its lower level of complications in contrast to surgical decompression. Neonatal dysmorphic syndrome is often associated with disorders of the central nervous system. So far, there have been no reports on the incidence of this disease with Ogilvie syndrome, although 9% of cases have been described as associated with neurological events. Conservative management in this disease is the initial approach. Interventions should be reserved for when conservative treatment fails.

No abstract