No abstract

No abstract

The ability to spatially control cellular adhesion in a continuous manner on a biocompatible substrate is an important factor in designing new biomaterials for use in wound healing and tissue engineering applications. In this work, a novel method of engineering cell-adhesive RGD-ligand density gradients to control specific cell adhesion across a substrate is presented. Polymer brushes exhibiting spatially defined gradients in chain density are created and subsequently functionalized with RGD to create ligand density gradients capable of inducing cell adhesion on an otherwise weakly adhesive substrate. Cell studies indicate that these ligand-functionalized surfaces are noncytotoxic, with cellular adhesion increasing with RGD-ligand density across the gradient brush surface.

Soft tissue reconstruction using tissue-engineered constructs requires the development of materials that are biocompatible and support cell adhesion and growth. The objective of this study was to evaluate the use of macroporous hydrogel fragments that were formed using either unmodified alginate or alginate covalently linked with the fibronectin cell adhesion peptide RGD (alginate-RGD). These materials were injected into the subcutaneous space of adult, domesticated female sheep and harvested for histological comparisons at 1 and 3 months. In addition, the alginate-RGD porous fragments were seeded with autologous sheep preadipocytes isolated from the omentum, and these cell-based constructs were also implanted. The results from this study indicate that both the alginate and alginate-RGD subcutaneous implants supported tissue and vascular ingrowth. Furthermore, at all time points of the experiment, a minimal inflammatory response and capsule formation surrounding the implant were observed. The implanted materials also maintained their sizes over the 3-month study period. In addition, the alginate-RGD fragments supported the adhesion and proliferation of sheep preadipocytes, and adipose tissue was present within the transplant site of these cellular constructs, which was not present within the biomaterial control sites.

Development of tissue-engineered devices may be enhanced by combining cells with porous absorbable polymeric scaffolds before implantation. The cells are seeded throughout the scaffolds and allowed to proliferate in vitro for a predetermined amount of time. The distribution of cells throughout the porous material is one critical component determining success or failure of the tissue-engineered device. This can influence both the successful integration of the device with the host tissue as well as the development of a vascularized network throughout the entire scaffold volume. This research sought to compare different seeding and proliferation methods to select an ideal method for a polyglycolide/aortic endothelial cell system. Two seeding environments, static and dynamic, and three proliferation environments, static, dynamic, and bioreactor, were analyzed, for a total of six possible methods. The six seeding and proliferation combinations were analyzed following a 1-week total culture time. It was determined that for this specific system, dynamic seeding followed by a dynamic proliferation phase is the least promising method and dynamic seeding followed by a bioreactor proliferation phase is the most promising.

Three-dimensional (3-D) culture of cancer cells and of normal mammalian cells in a polymeric matrix is generally a better alternate model for understanding the regulation of cancer cell proliferation and for evaluation of different anticancer drugs. A substantial amount of evidence demonstrates important differences in the behavior of cells grown in monolayer, i.e., two-dimensional (2-D), and in 3-D cultures. Cancer cells grown in 3-D culture are more resistant to cytotoxic agents than cells in 2-D culture; growth of cells in vitro in 3-D requires a suitable polymer that provides a structural scaffold for cell adhesion and growth. Many naturally derived polymers as well as synthetic polymers have been investigated as scaffolds. The aim of this review is to overview the polymeric materials of natural and synthetic origin that are of specific interest to 3-D cell cultures, and discuss the development of new polymers that should be specifically designed for 3-D culture applications.

There are many clinical situations in which a large tissue mass is required to replace tissue lost to surgical resection (e.g., mastectomy). It is possible that autologous cell transplantation on biodegradable polymer matrices may provide a new therapy to engineer large tissue which can be used to treat these patients. A number of challenges must be met to engineer a large soft tissue mass. These include the design of (1) a structural framework to maintain a space for tissue development, (2) a space-filling matrix which provides for localization of transplanted cells, and (3) a strategy to enhance vascularization of the forming tissue. In this paper we provide an overview of several technologies which are under development to address these issues. Specifically, support matrices to maintain a space for tissue development have been fabricated from polymers of lactide and glycolide. The ability of these structures to resist compressive forces was regulated by the ratio of lactide to glycolide in the polymer. Smooth muscle cell seeding onto polyglycolide fiber-based matrices has been optimized to allow formation of new tissues in vitro and in vivo. Finally, polymer microsphere drug delivery technology is being developed to release vascular endothelial growth factor (VEGF), a potent angiogenic molecule, at the site of tissue formation. This strategy, which combines several different technologies, may ultimately allow for the engineering of large soft tissues.

Tissue engineered biomaterial constructs are needed for plastic and reconstructive applications. To successfully form a space-filling tissue, the construct should induce a minimal inflammatory response, create minimal or no fibrotic capsule, and establish a vascular bed within the first few days after implantation to ensure survival of the implanted cells. In addition, the biomaterial should support cellular adhesion and induce tissue ingrowth. A macroporous hydrogel bead using sodium alginate covalently coupled with an arginine, glycine, and aspartic acid-containing peptide was created. A 6-month subcutaneous rat model study was performed to determine if the implanted material induced tissue ingrowth throughout the implantation area and maintained a three-dimensional vascular bed. The implanted materials produced a vascular bed, minimal inflammation and capsule formation, and good tissue ingrowth throughout the experiment. The material retained its bulking capacity by demonstration of no significant change of the cross-sectional area as measured from the center of the implants after the 2-week time point. In addition, the granulation tissue formed around the implant was loosely organized, and the surrounding tissue had integrated well with the implant. These results indicate that this material has the desired properties for the development of soft-tissue-engineering constructs.