Purpose The purpose of this study is to highlight the direct fabrication of rapid tooling (RT) with desired mechanical, tribological and thermal properties using fused deposition modelling (FDM) process. Further, the review paper demonstrated development procedure of alternative feedstock filament of low-cost composite material for FDM to extend the range of RT applications. Design/methodology/approach The alternative materials for FDM and their processing requirements for fabrication in filament form as reported by various researchers have been summarized. The literature demonstrates the role of various post-processing techniques on surface finish of FDM prints. Further, low-cost materials for feedstock filament have been investigated experimentally to check their adaptability/suitability for commercial FDM setup. The approach was to realize the requirements of FDM (melt flow rate, flexibility, stiffness, glass transition temperature and mechanical strength), necessary for the successful run of an alternative filament. The effect of constituents (additives, plasticizers, surfactants and fillers) in polymeric matrix on mechanical, tribological and thermal properties has been investigated. Findings It is possible to develop composite material feedstock as filament for commercial FDM setup without changing its hardware and software. Surface finish of the parts can further be improved by applying various post-processing techniques. Most of the composite parts have high mechanical strength, hardness, thermal stability, wear resistant and better bond formation than standard material parts. Research limitations/implications Future research may be focused on improving the surface quality of parts fabricated with composite feedstock, solving issues related to the uniform distribution of filled materials during the fabrication of feedstock filament which in turns further increases mechanical strength, high dimensional stability of composite filament and transferring the technology from laboratory scale to various industrial applications. Practical implications Potential applications of direct fabrication with RT includes rapid manufacturing (RM) of metal-filled parts and ceramic-filled parts (which have complex shape and cannot be rapidly made by any other manufacturing techniques) in the field of biomedical and dentistry. Originality/value This new manufacturing methodology is based on the proper selection and processing of various materials and additives to form high-performance, low-cost composite material feedstock filament (which fulfil the necessary requirements of FDM process). Finally, newly developed feedstock filament material has both quantitative and qualitative advantage in RT and RM applications as compared to standard material filament.

No abstract

Purpose The purpose of this paper is to fabricate Nylon6-Al-Al2O3-based alternative fused deposition modeling process (FDM) feedstock filament in place of commercial acrylonitrile butadiene styrene (ABS) filament (having required rheological and mechanical properties) for rapid manufacturing (RM) and rapid tooling (RT) applications. The detailed steps for fabrication of alternative FDM feedstock filament (as per field application) with relatively low manufacturing cost and tailor-made properties have been highlighted. Design/methodology/approach The rheological and mechanical suitability of nylon6-Al-Al2O3 feedstock filament has been investigated experimentally. The approach is to predict and incorporate essential properties such as flow rate, flexibility, stiffness and mechanical strength at processing conditions and compared with commercial ABS material. The proportions of various constituents have been varied to modify and improve rheological behavior and mechanical properties of alternative FDM feedstock filament. Findings The alternative material of feed stock filament was successfully developed and loaded in commercial FDM setup without changing any hardware and software. The result of study suggests that the newly developed composite material filament has relatively poor mechanical properties but have highly thermal stability and wear resistant as compared to ABS filament and hence can be used for tailor-made applications. Research limitations/implications In this work, no additive was added for improving the bond formation of metal and polymeric materials. The newly developed filament was prepared on single screw extruder. For more uniform mixing of metal and polymeric materials, further studies may be conducted on twin screw extruder. Also, for the present research work, the testing of newly developed filament has been limited up to mechanical testing, which may be extended to chemical and thermal analysis to understand thermal stability and degradation mechanism of newly developed composite material. Practical implications The proportion of filler material (Al-Al2O3) in Nylon6 matrix was set as a constraint, which was adjusted based upon melt flow index of original equipment manufacturer developed material (ABS), and temperature conditions were available at FDM nozzle (so that hardware and software system of commercial FDM setup need not to be altered). Originality/value The present approach outlined selection, processing, fabrication and testing procedure for alternate feedstock filament, which fulfills the necessary requirements of FDM process and has been customized for RT and RM applications. This work highlights mechanical strength evaluation of feedstock filament (which is necessary before the loading of material in FDM system). The potential applications of this investigation include RM of functional parts, tailor-made grinding tools for dentists and RT of metal matrix composite having complex geometry.

No abstract

No abstract

No abstract

No abstract

Purpose In this study the friction and wear behavior of fused deposition modeling (FDM) parts fabricated with composite material and acrylonitrile butadiene styrene (ABS) material feedstock filament were realized and compared under dry sliding conditions. Design/methodology/approach The tests were performed by applying the load of 5, 10, 15 and 20 N with sliding velocity of 0.63 m/s for the duration of 5 and 10 min at room temperature. Findings The results highlight various wear mechanisms such as adhesion, abrasion and fatigue during the investigation. It was observed that the wear volume, friction force, friction co-efficient and temperature were sensitive to the applied load and time duration. The composite material showed a remarkable improvement in wear properties as compared to the ABS material. Research limitations/implications The investigations reported in the present research work is based on comparative analysis (of composite material and ABS material feedstock filament). The results may be different in practical applications because of different operating conditions. Practical implications The parts fabricated with proposed composite material feedstock filament are highly wear resistant than basic ABS filament. This may lead to the development of better wear resistance components for numerous field applications. Originality/value The potential of this research work is to fabricate FDM parts with composite material feedstock filament to cater need of wear resistant industrial components.