Micro- and nanoelectromechanical oscillators driven at or close to their resonance frequency are used as sensors in many fields of science and technology. A decrease in the oscillator's effective spring constant and/or mass holds great potential for an increase in the sensor's sensitivity. This is usually accompanied by a reduction in spatial dimensions, which in most cases requires more complex detection methods. By analyzing the complex behavior of a simple asymmetric coupled harmonic oscillator model we propose a novel sensor concept which combines the advantages of bigger and smaller oscillators, i.e. ease of detection and high sensitivity. The concept is based on matching the resonance frequencies of two otherwise very different oscillators. To support our theoretical considerations, we present an experimental implementation of such a sensor and respective experimental data, verifying a substantial signal enhancement by several orders of magnitude.

SummaryCantilever magnetometry is a measurement technique used to study magnetic nanoparticles. With decreasing sample size, the signal strength is significantly reduced, requiring advances of the technique. Ultrathin and slender cantilevers can address this challenge but lead to increased complexity of detection. We present an approach based on the co-resonant coupling of a micro- and a nanometer-sized cantilever. Via matching of the resonance frequencies of the two subsystems we induce a strong interplay between the oscillations of the two cantilevers, allowing for a detection of interactions between the sensitive nanocantilever and external influences in the amplitude response curve of the microcantilever. In our magnetometry experiment we used an iron-filled carbon nanotube acting simultaneously as nanocantilever and magnetic sample. Measurements revealed an enhancement of the commonly used frequency shift signal by five orders of magnitude compared to conventional cantilever magnetometry experiments with similar nanomagnets. With this experiment we do not only demonstrate the functionality of our sensor design but also its potential for very sensitive magnetometry measurements while maintaining a facile oscillation detection with a conventional microcantilever setup.

motivated by a broad range of applications for magnetoresistive devices, optical meta-materials, cell-DNA separators, drug delivery vectors, [7,8] and wave based information transport. [9] Both, the high stability of their magnetic equilibrium state against external perturbations, as well as their robust domain walls, which propagate with velocities faster than the spin wave phase velocity, promote them as appealing candidates for racetrack memory devices and for information transport and processing using spin waves in magnonic applications.Various bottom-up synthesis routes for the preparation of magnetic nanowires exist; including for example electrodeposition based on porous membrane templates [1] and pyrolysis of metal-organic precursors. In particular the pyrolysis of ferrocene allows for the formation of iron-filled carbon nanotubes (FeCNT), i.e., multiwall carbon nanotubes, which contain single-phase single-crystalline iron nanowires, [10][11][12][13][14] where the body-centered cubic iron phase dominates. Furthermore, iron nanowires with various crystal orientations can be found with no prevalent orientation. [13] The diameters of the carbon nanotubes and the embedded iron nanowires are in the range of 30-100 and 10-40 nm, respectively. [13] The magnetization dynamics of individual Fe-filled multiwall carbonnanotubes (FeCNT), grown by chemical vapor deposition, are investigated by microresonator ferromagnetic resonance (FMR) and Brillouin light scattering (BLS) microscopy and corroborated by micromagnetic simulations. Currently, only static magnetometry measurements are available. They suggest that the FeCNTs consist of a single-crystalline Fe nanowire throughout the length. The number and structure of the FMR lines and the abrupt decay of the spin-wave transport seen in BLS indicate, however, that the Fe filling is not a single straight piece along the length. Therefore, a stepwise cutting procedure is applied in order to investigate the evolution of the ferromagnetic resonance lines as a function of the nanowire length. The results show that the FeCNT is indeed not homogeneous along the full length but is built from 300 to 400 nm long single-crystalline segments. These segments consist of magnetically high quality Fe nanowires with almost the bulk values of Fe and with a similar small damping in relation to thin films, promoting FeCNTs as appealing candidates for spin-wave transport in magnonic applications.The ORCID identification number(s) for the author(s) of this article can be found under https://doi.

Abstract. Understanding the behaviour of mechanical systems can be facilitated and improved by employing electro-mechanical analogies. These analogies enable the use of network analysis tools as well as purely analytical treatment of the mechanical system translated into an electric circuit. Recently, we developed a novel kind of sensor set-up based on two coupled cantilever beams with matched resonance frequencies (co-resonant coupling) and possible applications in magnetic force microscopy and cantilever magnetometry. In order to analyse the sensor's behaviour in detail, we describe it as an electric circuit model. Starting from a simplified coupled harmonic oscillator model with neglected damping, we gradually increase the complexity of the system by adding damping and interaction elements. For each stage, various features of the coupled system are discussed and compared to measured data obtained with a co-resonant sensor. Furthermore, we show that the circuit model can be used to derive sensor parameters which are essential for the evaluation of measured data. Finally, the much more complex circuit representation of a bending beam is discussed, revealing that the simplified circuit model of a coupled harmonic oscillator is a very good representation of the sensor system.

No abstract

We present a bimodal magnetic force microscopy sensor consisting of a conventional cantilever beam, a spacer element, and an iron-filled carbon nanotube. Depending on the mode of the cantilever's resonant flexural vibration, the sensor is sensitive to magnetic field derivatives parallel and perpendicular to the sample's surface. This multifunctionality is supported by the scalar-type behavior of the magnetic monopole-like end of the iron-filled carbon nanotube.

There is a strong commercial need for inexpensive point-of-use sensors for monitoring disease biomarkers or environmental contaminants in drinking water. Point-of-use sensors that employ smart polymer hydrogels as recognition elements can be tailored to detect almost any target analyte, but often suffer from long response times. Hence, we describe here a fabrication process that can be used to manufacture low-cost point-of-use hydrogel-based microfluidics sensors with short response times. In this process, mask-templated UV photopolymerization is used to produce arrays of smart hydrogel pillars inside sub-millimeter channels located upon microfluidics devices. When these pillars contact aqueous solutions containing a target analyte, they swell or shrink, thereby changing the resistance of the microfluidic channel to ionic current flow when a small bias voltage is applied to the system. Hence resistance measurements can be used to transduce hydrogel swelling changes into electrical signals. The only instrumentation required is a simple portable potentiostat that can be operated using a smartphone or a laptop, thus making the system suitable for point of use. Rapid hydrogel response rate is achieved by fabricating arrays of smart hydrogels that have large surface area-to-volume ratios.

The investigation of properties of nanoparticles is an important task to pave the way for progress and new applications in many fields of research like biotechnology, medicine and magnetic storage techniques. The study of nanoparticles with ever decreasing size is a challenge for commonly employed methods and techniques. It requires increasingly complex measurement setups, often low temperatures and a size reduction of the respective sensors to achieve the necessary sensitivity and resolution. Here, we present results on how magnetic properties of individual nanoparticles can be measured at room temperature and with a conventional scanning force microscopy setup combined with a co-resonant cantilever magnetometry approach. We investigate individual Co2FeGa Heusler nanoparticles with diameters of the order of 35 nm encapsulated in carbon nanotubes. We observed, for the first time, magnetic switching of these nanoparticles in an external magnetic field by simple laser deflection detection. Furthermore, we were able to deduce magnetic properties of these nanoparticles which are in good agreement with previous results obtained with large nanoparticle ensembles in other experiments. In order to do this, we expand the analytical description of the frequency shift signal in cantilever magnetometry to a more general formulation, taking unaligned sensor oscillation directions with respect to the magnetic field into account.