RESUMO:Sabe-se que a determinação precisa da evapotranspiração da cultura (ETc) é de grande importância para o uso eficiente da água, principalmente em regiões áridas e semiáridas onde se faz necessária a utilização de água salina para irrigação. O objetivo deste trabalho foi determinar a evapotranspiração da melancia, cultivar Mickylee, com o uso de diferentes níveis de salinidade da água de irrigação. O experimento foi conduzido na Fazenda Experimental da Alagoinha, pertencente à Universidade Federal Rural do Semiárido, Mossoró -RN. Os níveis de salinidade da água de irrigação foram: S1 = 0,55; S2 = 1,65; S3 = 2,35; S4 = 3,5, e S5 = 4,5 dS m -1 , sendo os tratamentos dispostos no delineamento de blocos ao acaso, com quatro repetições. A determinação da evapotranspiração de referência (ETo) foi realizada pelo método FAO-Penmam-Monteith, e a ETc, pelas leituras obtidas em lisímetros de pesagem, instalados nos tratamentos S1 e S5. Os resultados mostraram que a ETc da melancia diminui com o aumento da salinidade da água aplicada e que a evapotranspiração total durante o ciclo foi de 245 e 214 mm, respectivamente, para os tratamentos S1 e S5. Os valores médios de Kc obtidos para cada fase fenológica foram 0,23; 0,68; 1,12; 0,90 e 0,24; 0,61; 0,98 e 0,78, respectivamente, para as águas S1 e S5. PALAVRAS-CHAVE:Citrullus lanatus, água salina, coeficiente de cultivo. EVAPOTRANSPIRATION OF WATERMELON IRRIGATED WITH DIFFERENT SALINITY WATERSABSTRACT: The knowledge of crop evapotranspiration (ETc) is very important for efficient water use in irrigated crops, mainly in arid and semi-arid regions, where the use of saline water is common. The objective of this study was to determine watermelon crop evapotranspiration (cv. Mickylee) in plants submitted to different irrigation water salinity levels. The experiment was carried out at the Experimental field of the Semi-Arid Federal Rural University, Mossoró, RN, Brazil. The irrigation water salinity levels were of S1 = 0.55; S2 = 1.65; S3 = 2.35; S4 = 3.5 and S5 = 4.5 dS m -1 , with the treatments set up in randomized blocks with four replications. The determination of reference evapotranspiration (ETo) was accomplished by FAO-Penmam-Monteith method, and ETc was determined by two weighting lysimeters installed in the treatments S1 and S5. The results showed that watermelon ETc decreases with the increase of salinity in the irrigation water. The total ETc during the evaluated period was 245 and 214 mm, respectively for S1 and S5. The Kc medium values obtained for growth stage were: 0.23, 0.68, 1.12 and 0.90 for water S1, and 0.24; 0.61; 0.98 and 0.78 for S5.
RESUMO:Neste trabalho, ajustou-se um modelo matemático para quantificar o efeito da variação do rendimento da bomba hidráulica na variação dos custos de um sistema de bombeamento, na estrutura tarifária horossazonal verde (subgrupo A4) e o tempo de recuperação do capital investido no equipamento de maior rendimento. Em seguida, o mesmo foi aplicado a um sistema de bombeamento para suprimento de um sistema de irrigação do tipo pivô central. As opções de rendimento da bomba hidráulica foram: 69,5% (bomba 1), 73% (bomba 2) e 78% (bomba 3), cujos custos de aquisição foram, respectivamente, R$ 6.176,00, R$ 8.479,00 e R$ 15.509,00. Os resultados da aplicação do modelo mostraram que: i) a substituição da bomba 1 pela bomba 2 foi viável, sendo o período de recuperação de capital 3,4 anos; ii) a substituição da bomba 1 pela bomba 3 foi viável, sendo o período de recuperação de capital 9,2 anos; iii) a substituição da bomba 2 pela bomba 3 foi inviável, sendo o período de recuperação de capital 21,1 anos superior ao período de amortização do investimento na avaliação econômica, considerado 15 anos. PALAVRAS-CHAVE: modelo matemático, energia e custos. INVESTMENT RECOVERY PERIOD IN HYDRAULIC PUMP OF BETTER EFFICIENCY IN PUMPING SYSTEMS IN THE GREEN HOURLY SEASONAL TARIFF FOR IRRIGATIONABSTRACT: In this study a mathematical model was adjusted to quantify the effect of the pump efficiency on cost variation of the pumping system in the green hourly seasonal tariff (subgroup A4 -irrigation) and the investment recovery period by a more efficient pumping station. Afterwards, the same model was applied in a pumping system supplying a center pivot irrigation machine. The hydraulics pump efficiency options were: 69.5% (pump 1), 73% (pump 2) and 78% (pump 3), with acquisition costs of R$ 6,176.00, R$ 8,479.00 and R$ 15,509.00, respectively. The results of the model applied showed that: i) the substitution of pump 1 for 2 was feasible, being the investment recovery period of 3.4 years; ii) the substitution of bomb 1 for 3 was feasible, being the investment recovery period of 9.2 years; and iii) the substitution of bomb 2 for 3 was unfeasible, being the investment recovery period of 21.1 years, therefore superior to its useful life span, considered 15 years.
A utilização de métodos de fácil aplicação e com resultados rápidos são importantes para que os produtores de milho possam decidir o momento correto para realização da colheita com redução das perdas com a secagem natural. Objetivou-se estudar o teor de água ideal dos grãos na colheita da cultura do milho, a produtividade e os componentes produtivos, bem como as perdas com a secagem natural em campo. O delineamento experimental foi o de blocos ao acaso com quatro repetições e os tratamentos consistiram na colheita nos seguintes teores de água em base úmida (b.u.) dos grãos: 28,9 (ponto de maturidade fisiológica plena), 23,5; 21,9; 18,9; 16,1; e 13,8%, avaliando-se a umidade do ápice, meio e base da espiga, altura de plantas, altura de inserção de espigas, diâmetro do colmo, número de fileiras e grãos por fileiras, número de grãos por espiga, prolificidade, massa de 100 grãos e produtividade de grãos. Os componentes produtivos relacionados à planta e aos grãos não foram influenciados pela umidade de grãos na ocasião da colheita. A umidade da ápice, meio e base da espiga, massa de 100 grãos e a produtividade de grãos de milho foram influenciados pela umidade de grãos na ocasião da colheita.
Resumo Este artigo é resultado da pesquisa que investigou a percepção ambiental dos moradores do entorno dos Parques Municipais Urbanos das Lagoas das Bateias e do Jurema (Vitória da Conquista, BA). Com base numa metodologia empírico-bibliográfica, constituída de três fases: revisão bibliográfica, pesquisa de campo (incluindo focus group) e análise de dados, discutiu-se sobre a importância da conservação ambiental a partir das percepções e representações sobre estas Unidades de Conservação (UC). O artigo, desta forma, contribui para o conhecimento de instrumentos como a influência da representação, a obrigatoriedade legal e o imperativo para a proteção dessas (UC). A análise fornece subsídios para a política ambiental da cidade, sobretudo no que se refere às subjetividades da (re)produção do espaço urbano. Palavras-chave: Conservação ambiental; Unidades de Conservação Urbana; Percepção ambiental. Abstract This article is the result of the research that investigated the environmental perception of the residents of the Urban Municipal Parks of Lagoas das Bateias and Jurema (Vitória da Conquista, BA). Based on an empirical-bibliographic methodology, made up of three phases: bibliographical review, field research (including focus group) and data analysis, the importance of environmental conservation based on perceptions and representations about these Conservation Units (UC). The article thus contributes to the knowledge of instruments such as the influence of representation, the legal obligation and the imperative to protect these (UC). The analysis provides subsidies for the city's environmental policy, especially with regard to the subjectivities of (re) production of the urban space.
ABSTRACT:In this study, it was adjusted a mathematical model to measure the effect of electric motor efficiency on pumping system costs for irrigation on the tariff structure of conventional electricity and green horo-seasonal , and also to calculate the recovery period of the invested capital in higher efficiency equipment. Then, it was applied to a center pivot irrigation system in two options of electric motor efficiency, 92,6% (standard line) and 94,3% (high efficiency line), and the acquisition cost of the first corresponded to 70% the of the second. The power of the electric motor was 100hp. The results showed that the model allowed us to evaluate if a high efficiency motor was economically viable compared to the standard motor in each tariff structure. The high efficiency motor was not viable in the two tariff structures. In the green horo-seasonal tariff, would only be viable if its efficiency was 4.46% higher than the standard motor. In the conventional tariff, it would only be viable if the efficiency overcame 2.71%.KEYWORDS: conventional tariff, green horo-seasonal tariff, high efficiency. PERÍODO DE RECUPERAÇÃO DO CAPITAL INVESTIDO EM MOTOR ELÉTRICO DE MELHOR RENDIMENTO NO BOMBEAMENTO PARA IRRIGAÇÃORESUMO: Neste trabalho, ajustou-se um modelo matemático para quantificar o efeito do rendimento do motor elétrico sobre os custos de um sistema de bombeamento para irrigação na estrutura tarifária de energia elétrica convencional e horo-sazonal verde, bem como calcular o tempo de recuperação do capital investido no equipamento de maior rendimento. Em seguida, o mesmo foi aplicado a um sistema de irrigação tipo pivô central em duas opções de rendimento do motor elétrico: 92,6% (linha padrão) e 94,3% (linha alto rendimento), sendo que o custo de aquisição do primeiro correspondeu a 70% do segundo. A potência do motor elétrico era de 100 cv. Os resultados mostraram que o modelo permitiu avaliar se um motor de alto rendimento era viável economicamente em relação ao motor-padrão em cada estrutura tarifária. Nas duas estruturas tarifárias, o motor de alto rendimento não foi viável. Na tarifa horo-sazonal verde, somente seria viável se seu rendimento fosse 4,46% superior ao do motor-padrão. Na tarifa convencional, somente seria viável se o ganho de rendimento superasse 2,71%. PALAVRAS-CHAVE:tarifa convencional, tarifa horo-sazonal verde, alto rendimento.Investment recovery period in electric motor of higher efficiency in pumping for irrigationEng.
RESUMO:Neste trabalho, foi simulado o custo da irrigação de um sistema tipo pivô central com diferentes comprimentos da tubulação de recalque e desníveis topográficos na produção do feijoeiro comum, na região de Ilha Solteira -SP, bem como sua receita líquida. Considerou-se uma área irrigada pelo equipamento de 103,58 ha, sendo sua configuração a mais econômica possível para as variáveis consideradas. A participação da irrigação no custo de produção do feijoeiro variou de 14,8 a 21,5% entre as condições extremas, ou seja, do menor desnível topográfico (40 m) e comprimento da tubulação de recalque (2.000 m) ao maior desnível (80 m) e comprimento (3.000 m). Em todas as configurações do sistema de irrigação e com os preços praticados em agosto de 2008 ou com o preço histórico médio, seria viável a cultura do feijoeiro, proporcionando rendas líquidas de até R$ 3.959,64 ha -1 e até R$ 1.203,14 ha -1 , respectivamente. PALAVRAS-CHAVE: pivô central, feijoeiro, custos e lucros. BEAN COST OF IRRIGATION AND PROFIT IN A CENTER PIVOT SYSTEM UNDER VARIATION OF PRESSURIZED PIPE LENGTH AND TOPOGRAPHIC LEVELSABSTRACT: In this study it was simulated the cost of irrigation by a center pivot system under different pressurized pipe length and topographic levels in the brown bean growing, as well its profit. It was considered an irrigated area of 103.58 ha, being set the most economic system configuration from the considered variables. The cost of irrigation in brown bean growing ranged from 14.8 to 21.5% between the extreme conditions, in the lower topographic level (40 m) and pressurized pipe length (2,000 m) to the largest topographic level (80 m) and length (3,000 m). In all irrigation system settings and with prices in August 2008 or the average historic price it would be viable the brown bean growing, providing profits until R$ 3,959.64 and R$ 1,203.14 ha -1 , respectively.
RESUMOPara se realizar a técnica da quimigação é necessário que o sistema de irrigação possua um injetor para incorporar os produtos na água de irrigação. Dentre os métodos existentes, o que tem se destacado nos últimos anos é o injetor do tipo Venturi. Essa preferência tem sido motivada pela sua simplicidade, por não possuir peças móveis e ser de baixo custo. Apesar dessas vantagens, o uso do injetor Venturi, assim como os demais injetores, necessita de dispositivos de segurança que minimizem o risco de contaminação ambiental. Neste trabalho, objetivou-se analisar a influência da válvula de retenção na taxa de injeção de água de um injetor do tipo Venturi instalado em pivô central e seu rendimento. O dispositivo de injeção era constituído de um injetor Venturi de 1,5 polegadas associado a uma motobomba centrífuga de 2,2 kW. O equipamento foi instalado na base do pivô central. Foram tomados tempos de esvaziamento de um reservatório de volume de 20 litros. O delineamento experimental utilizado foi o inteiramente casualizado, sendo realizadas dez repetições em cada situação avaliada, ou seja, injetor equipado com válvula de retenção e sem a presença da mesma. Aplicou-se a análise de variância, seguida do teste de Tukey. Concluiu-se que a presença de válvula de retenção em injetores do tipo Venturi não influenciou de forma significativa as taxas de injeção e o rendimento, tendo este último apresentado valores da ordem de 10%. COMPARATIVE STUDY OF THE INJECTION RATE AS FROM INJENTOR VENTURI EQUIPPED WITH AND WITHOUT CHECK VALVE 2 SUMMARYTo carry out the technique of chemigation is necessary that the irrigation system has an injector incorporating the product into irrigation water. Among the existing methods, which has emerged in recent years is the Venturi injector. This preference has been motivated by its simplicity, has no moving parts and be low cost. Despite these advantages, the use of the Venturi nozzle, as well as other injectors, require safety devices to minimize the risk of environmental contamination. This study aimed to analyze the influence of the check valve in the water injection rate from the Venturi injector installed on a center pivot as its efficiency. The injection device was made of a Venturi injector size 1.5 inch connected to a centrifugal pump of 2.2 kW. The equipment was installed at the base of the central pivot. The emptying
The purpose of this paper was to develop a model for calculating the economical flow diameter and velocity, by obtaining the economical diameter, using Swamee's friction factor equation, by minimizing the total annual cost. The application of the model to a regular supply condition showed that the diameter of the actual condition, 250 mm, compared with the diameter calculated by the mode, at the same tariff as that applied to the property (ground), 284.1 mm, involved the necessity to generate, transmit, and distribute extra electrical energy, due to the higher load loss caused by the original diameter, approximately 30800 kWh/year. This means that in one year, the consumer would spend R$2,804.00 more on pumping cost alone.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.