Ternary organic solar cells are promising candidates for bulk heterojunction solar cells; however, improving the power conversion efficiency (PCE) is quite challenging because the ternary system is complicated on phase separation behavior. In this study, a ternary organic solar cell (OSC) with two donors, including one polymer (PTB7-Th), one small molecule (p-DTS(FBTTH2)2), and one acceptor (PC71BM), is fabricated. We propose the two donors in the ternary blend forms an alloy. A notable averaged PCE of 10.5% for ternary OSC is obtained due to the improvement of the fill factor (FF) and the short-circuit current density (J(sc)), and the open-circuit voltage (V(oc)) does not pin to the smaller V(oc) of the corresponding binary blends. A highly ordered face-on orientation of polymer molecules is obtained due to the formation of an alloy structure, which facilitates the enhancement of charge separation and transport and the reduction of charge recombination. This work indicates that a high crystallinity and the face-on orientation of polymers could be obtained by forming alloy with two miscible donors, thus paving a way to largely enhance the PCE of OSCs by using the ternary blend strategy.

Solution-processable small molecules for organic solar cells have attracted intense attention for their advantages of definite molecular structures compared with their polymer counterparts. However, the device efficiencies based on small molecules are still lower than those of polymers, especially for inverted devices, the highest efficiency of which is <9%. Here we report three novel solution-processable small molecules, which contain π-bridges with gradient-decreased electron density and end acceptors substituted with various fluorine atoms (0F, 1F and 2F, respectively). Fluorination leads to an optimal active layer morphology, including an enhanced domain purity, the formation of hierarchical domain size and a directional vertical phase gradation. The optimal morphology balances charge separation and transfer, and facilitates charge collection. As a consequence, fluorinated molecules exhibit excellent inverted device performance, and an average power conversion efficiency of 11.08% is achieved for a two-fluorine atom substituted molecule.

Manipulating the donor:acceptor (D:A) energetics, e.g. the highest occupied molecular orbital (HOMO) offset, is the key to balancing the charge separation and charge recombination for high-performance organic solar cells (OSCs)....

Developing a high-performance donor polymer is critical for achieving efficient non-fullerene organic solar cells (OSCs). Currently, most high-efficiency OSCs are based on a donor polymer named PM6, unfortunately, whose performance is highly sensitive to its molecular weight and thus has significant batch-to-batch variations. Here we report a donor polymer (named PM1) based on a random ternary polymerization strategy that enables highly efficient non-fullerene OSCs with efficiencies reaching 17.6%. Importantly, the PM1 polymer exhibits excellent batch-to-batch reproducibility. By including 20% of a weak electron-withdrawing thiophene-thiazolothiazole (TTz) into the PM6 polymer backbone, the resulting polymer (PM1) can maintain the positive effects (such as downshifted energy level and reduced miscibility) while minimize the negative ones (including reduced temperature-dependent aggregation property). With higher performance and greater synthesis reproducibility, the PM1 polymer has the promise to become the work-horse material for the non-fullerene OSC community.

A ternary blend system with two donors and one acceptor provides an effective route to improve the performance of organic solar cells. A synergistic effect of polymer and small molecules is observed in ternary solar cells, and the power conversion efficiency (PCE) of the ternary system (8.40%) is higher than those of binary systems based on small molecules (7.48%) or polymers (6.85%).

In this work, a nonfullerene polymer solar cell (PSC) based on a wide bandgap polymer donor PM6 containing fluorinated thienyl benzodithiophene (BDT-2F) unit and a narrow bandgap small molecule acceptor 2,2'-((2Z,2'Z)-((4,4,9,9-tetrahexyl-4,9-dihydro-s-indaceno[1,2-b:5,6-b']dithiophene-2,7-diyl)bis(methanylylidene))bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (IDIC) is developed. In addition to matched energy levels and complementary absorption spectrum with IDIC, PM6 possesses high crystallinity and strong π-π stacking alignment, which are favorable to charge carrier transport and hence suppress recombination in devices. As a result, the PM6:IDIC-based PSCs without extra treatments show an outstanding power conversion efficiency (PCE) of 11.9%, which is the record value for the as-cast PSC devices reported in the literature to date. Moreover, the device performances are insensitive to the active layer thickness (≈95-255 nm) and device area (0.20-0.81 cm ) with PCEs of over 11%. Besides, the PM6:IDIC-based flexible PSCs with a large device area of 1.25 cm exhibit a high PCE of 6.54%. These results indicate that the PM6:IDIC blend is a promising candidate for future roll-to-roll mass manufacturing and practical application of highly efficient PSCs.

Ternary blending strategy has been used to design and fabricate efficient organic solar cells by enhancing the short-circuit current density and the fill factor. In this manuscript, we report all-small-molecule ternary solar cells consisting of two compatible small molecules DR3TBDTT (M1) and DR3TBDTT-E (M2) as donors and PCBM as acceptor. A transformation from an alloy-like model to a cascade model are first realized by designing a novel molecule M2. It is observed that after thermal and solvent vapor annealing M2 shifts from the mixed region to donor-acceptor (D-A) interfaces which ameliorates the charge transfer and recombination processes. The optimal ternary solar cells with 10% M2 exhibited a power conversion efficiency of 8.48% in the alloy-like model and 10.26% in the cascade model. The proposed working mechanisms are fully characterized and further supported by the density functional theory and atomistic molecular dynamics simulations. This provides an important strategy to design high-performance ternary solar cells which contains one molecule not only is compatible with the main donor molecule but also performs a preference to appear at the D-A interfaces hence builds cascade energy levels.

Large-scale fabrication of organic solar cells requires an active layer with high thickness tolerability and the use of environment-friendly solvents. Thick films with high-performance can be achieved via a ternary strategy studied herein. The ternary system consists of one polymer donor, one small molecule donor, and one fullerene acceptor. The small molecule enhances the crystallinity and face-on orientation of the active layer, leading to improved thickness tolerability compared with that of a polymer-fullerene binary system. An active layer with 270 nm thickness exhibits an average power conversion efficiency (PCE) of 10.78%, while the PCE is less than 8% with such thick film for binary system. Furthermore, large-area devices are successfully fabricated using polyethylene terephthalate (PET)/Silver gride or indium tin oxide (ITO)-based transparent flexible substrates. The product shows a high PCE of 8.28% with an area of 1.25 cm for a single cell and 5.18% for a 20 cm module. This study demonstrates that ternary organic solar cells exhibit great potential for large-scale fabrication and future applications.