From a biomechanical point of view, the femoral neck system is a valid alternative to treat unstable femoral neck fractures, representing the advantages of a minimally invasive implant with comparable stability to the 2 DHS systems and superior to cannulated screws.

Operative treatment of sacral insufficiency fractures is frequently being complicated by osteopenic bone properties. Cement augmentation of implanted sacroiliac screws may lead to superior construct stability and prevent mechanical complications. A novel hemi-pelvis test model with dissected symphysis was developed. Five fresh-frozen cadaveric pelvises were vertically osteotomized at the sacrum on both sides and fixed with sacroiliac screws in both corridors of the first sacral vertebral body. One side was randomly augmented with bone cement. Cyclic testing consisting of torsional loading (±2.5 Nm) combined with progressively increasing axial loading (+50 N compression, -10 N traction, ±0,01 N/cycle) was performed until failure; simulated physiological loads derived from inverse dynamic calculations. The fixation was analyzed fluoroscopically quantifying screw migrations and assessing failure mechanisms. Failure modes were cut-out, pull-out, screw-out, and washer penetration. Motion at fracture site was analyzed via optical motion tracking. Unscrewing was provoked four times with non-augmented and twice with augmented screws. When focusing on the sacral region only, cement augmentation significantly improved screw fixation in terms of increased number of cycles to failure (p = 0.043). However, when considering overall construct stability, there was no significant difference between augmented and non-augmented state due to washer penetration at the iliac bone. The generated hemi-pelvis model was found to be valid due to the reproduction of the clinically observed failure mode (unscrewing). Unscrewing was not fully prevented by cement augmentation. Augmentation effects stability at the screw tip, but particularly in porotic bone, failure may shift to the next weak point. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:1485-1493, 2017.

Summary Objectives To evaluate the biomechanical performance of the Femoral Neck System (FNS) versus the Hansson Pin System (Hansson Pins) with two parallel pins in a Pauwels II femoral neck fracture model with posterior comminution. Methods Forty-degree Pauwels II femoral neck fractures AO 31-B2.1 with 15° posterior wedge were simulated in fourteen paired fresh-frozen human femora, followed by instrumentation with either FNS or Hansson Pins in pair-matched fashion. Implant positioning was quantified by measuring shortest implant distances to inferior cortex (DI) and posterior cortex (DP) on anteroposterior and axial X-rays, respectively. Biomechanical testing was performed in 20° adduction and 10° flexion with simulated iliopsoas muscle tension. Progressively increasing cyclic loading was applied until construct failure. Interfragmentary femoral head-to-shaft movements were measured with optical motion tracking. Results Cycles to 10° varus deformation were significantly higher for FNS (23007 ​± ​5496) versus Hansson Pins (17289 ​± ​4686), P ​= ​0.027. Cycles to 10° femoral head dorsal tilting (FNS: 12765 ​± ​3425; Hansson Pins: 13357 ​± ​6104) and cycles to 10° rotation around the femoral neck axis (FNS: 24453 ​± ​5073; Hansson Pins: 20185 ​± ​11065) were comparable between the implants, P ​≥ ​0.314. For Hansson Pins, the outcomes for varus deformation and dorsal tilting correlated significantly with DI and DP, respectively (P ​≤ ​0.047), whereas these correlations were not significant for FNS (P ​≥ ​0.310). Conclusions From a biomechanical perspective, by providing superior resistance against varus deformation and performing in a less sensitive way to variations in implant placement, the angular stable Femoral Neck System can be considered as a valid alternative to the Hansson Pin System for the treatment of Pauwels II femoral neck fractures. Level of evidence therapeutic, Level V. The Translational potential of this article The translational potential of this article is to compare the performance of the FNS with Hansson Pins in a AO 31-B2.1 fracture model featuring a 15 posterior wedge to show the implants behavior concerning the dorsal tilting tendency.

No abstract

Supplemental Digital Content is available in the text

Surgical reduction of a small PMF with less than 25% ankle joint surface improves pressure distribution but does not affect ankle joint stability. Cite this article: 2018;100-B:95-100.

Treatment of complex osteoporotic distal femur fractures with the Less Invasive Stabilization System (LISS) has been associated with high complication rates. The aim of this study was to investigate the biomechanical competence of two different techniques of augmented versus conventional LISS plating. Unstable distal femoral fracture AO/OTA 33-A3 was created via osteotomies in artificial femora simulating osteoporotic bone. Three study groups, consisting of 10 specimens each, were created for fixation with either LISS plate, LISS plate with additional polylactide intramedullary graft, or LISS plate plus medial locking plate (double plating). All specimens were non-destructively tested under axial (20-150 N) and torsional (0-4 Nm) quasi-static loading. Each bone-implant construct was tested with two different working length (WL) configurations (long and short) of the LISS plate. Relative movements between the most medial superior and inferior osteotomy aspects were investigated via three-dimensional motion tracking analysis. Double plating revealed significantly smaller longitudinal and shear displacement than the other two techniques (p ≤ 0.001). In addition, LISS plus graft fixation was with significantly less longitudinal displacement in comparison to conventional LISS plating (p < 0.001). Long WL resulted in significantly higher longitudinal and shear displacement compared to short WL for LISS and LISS plus graft (p ≤ 0.032), but not for double plating (p > 0.999). In conclusion, intramedullary grafting resulted in significantly increased fracture stability under axial loading in comparison to conventional LISS plating. Although it was not efficient enough to provide comparable stability to double plating, intramedullary grafting may be considered as a useful biological alternative to the latter in a surgeon's armamentarium. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:2604-2611, 2018.

In patients with fixed cavovarus feet, both SMOT and LCOT provided equally good redistribution of elevated ankle joint contact forces. Increasing the amount of displacement did not seem to equally improve the joint pressures. The site of osteotomy could therefore be chosen on the basis of surgeon's preference, simplicity, or local factors in case of more complex reconstructions.