Improving the long-term stability of perovskite solar cells is critical to the deployment of this technology. Despite the great emphasis laid on stability-related investigations, publications lack consistency in experimental procedures and parameters reported. It is therefore challenging to reproduce and compare results and thereby develop a deep understanding of degradation mechanisms. Here, we report a consensus between researchers in the field on procedures for testing perovskite solar cell stability, which are based on the International Summit on Organic Photovoltaic Stability (ISOS) protocols. We propose additional procedures to account for properties specific to PSCs such as ion redistribution under electric fields, reversible degradation and to distinguish ambient-induced degradation from other stress factors. These protocols are not intended as a replacement of the existing qualification standards, but rather they aim to unify the stability assessment and to understand failure modes. Finally, we identify key procedural information which we suggest reporting in publications to improve reproducibility and enable large data set analysis.

We report on accelerated degradation testing of MAPbX3 films (X = I or Br) by exposure to concentrated sunlight of 100 suns and show that the evolution of light absorption and the corresponding structural modifications are dependent on the type of halide ion and the exposure temperature. One hour of such exposure provides a photon dose equivalent to that of one sun exposure for 100 hours. The degradation in absorption of MAPbI3 films after exposure to 100 suns for 60 min at elevated sample temperature (∼45-55 °C), due to decomposition of the hybrid perovskite material, is documented. No degradation was observed after exposure to the same sunlight concentration but at a lower sample temperature (∼25 °C). No photobleaching or decomposition of MAPbBr3 films was observed after exposure to similar stress conditions (light intensity, dose, and temperatures). Our results indicate that the degradation is highly dependent on the hybrid perovskite composition and can be light- and thermally enhanced.

Functionalized and fully characterized graphene-based lubricant additives are potential 2D materials for energy-efficient tribological applications in machine elements, especially at macroscopic contacts. Two different reduced graphene oxide (rGO) derivatives, terminated by hydroxyl and epoxy-hydroxyl groups, were prepared and blended with two different molecular weights of polyethylene glycol (PEG) for tribological investigation. Epoxy-hydroxyl-terminated rGO dispersed in PEG showed significantly smaller values of the friction coefficient. In this condition, PEG chains intercalate between the functionalized graphene sheets, and shear can take place between the PEG and rGO sheets. However, the friction coefficient was unaffected when hydroxyl-terminated rGO was coupled with PEG. This can be explained by the strong coupling between graphene sheets through hydroxyl units, causing the interaction of PEG with the rGO to be non- effective for lubrication. On the other hand, antiwear properties of hydroxyl-terminated rGO were significantly enhanced compared to epoxy-hydroxyl functionalized rGO due to the integrity of graphene sheet clusters.

No abstract

Grain boundaries (GBs) participate in the photovoltaic energy conversion process in polycrystalline solar cells as efficient photocurrent collectors and transporters, as shown by high‐ resolution characterization of CdTe GBs in CdTe/CdS cells (see Figure). This suggests that structural defects can be advantageous for device performance, if properly designed, even in devices whose operation is based on physics of ideal, perfect solids.

The superior performance of certain polycrystalline (PX) solar cells compared to that of corresponding single‐crystal ones has been an enigma until recently. Conventional knowledge predicted that grain boundaries serve as traps and recombination centers for the photogenerated carriers, which should decrease cell performance. To understand if cell performance is limited by grain bulk, grain surface, and/or grain boundaries (GBs), we performed high‐resolution mapping of electronic properties of single GBs and grain surfaces in PX p‐CdTe/n‐CdS solar cells. Combining results from scanning electron and scanning probe microscopies, viz., capacitance, Kelvin probe, and conductive probe atomic force microscopies, and comparing images taken under varying conditions, allowed elimination of topography‐related artifacts and verification of the measured properties. Our experimental results led to several interesting conclusions: 1) current is depleted near GBs, while photocurrents are enhanced along the GB cores; 2) GB cores are inverted, which explains GB core conduction. Conclusions (1) and (2) imply that the regions around the GBs function as an extension of the carrier‐collection volume, i.e., they participate actively in the photovoltaic conversion process, while conclusion (2) implies minimal recombination at the GB cores; 3) the surface potential is diminished near the GBs; and 4) the photovoltaic and metallurgical junction in the n‐CdS/p‐CdTe devices coincide. These conclusions, taken together with gettering of defects and impurities from the bulk into the GBs, explain the good photovoltaic performance of these PX cells (at the expense of some voltage loss, as is indeed observed). We show that these CdTe GB features are induced by the CdCl2 heat treatment used to optimize these cells in the production process.

Photosynthesis is used by plants, algae and bacteria to convert solar energy into stable chemical energy. The initial stages of this process--where light is absorbed and energy and electrons are transferred--are mediated by reaction centres composed of chlorophyll and carotenoid complexes. It has been previously shown that single small molecules can be used as functional components in electric and optoelectronic circuits, but it has proved difficult to control and probe individual molecules for photovoltaic and photoelectrochemical applications. Here, we show that the photocurrent generated by a single photosynthetic protein-photosystem I-can be measured using a scanning near-field optical microscope set-up. One side of the protein is anchored to a gold surface that acts as an electrode, and the other is contacted by a gold-covered glass tip. The tip functions as both counter electrode and light source. A photocurrent of ∼10 pA is recorded from the covalently bound single-protein junctions, which is in agreement with the internal electron transfer times of photosystem I.

The operational stability of perovskite solar cells (PSCs) remains a limiting factor in their commercial implementation. We studied the long-term outdoor stability of ITO/SnO2/Cs0.05((CH3NH3)0.15(CH­(NH2)2)0.85)0.95PbI2.55Br0.45/spiro-OMeTAD/Au cells, as well as the dynamics of their degradation, under simulated sunlight indoors and their recovery in the dark. The extent of overall degradation was found to depend on processes occurring both under illumination and in the dark, i.e., during the daytime and nighttime, with the dynamics varying with cell aging. Full recovery of efficiency in the dark was observed for cells at early degradation stages. Further cell degradation resulted in recovery times much longer than one night, appearing as irreversible degradation under real operational conditions. At later degradation stages, very different dynamics were observed: short-circuit current density and fill factor exhibited a pronounced drop upon light turn-off but strong improvement under subsequent illumination. The interplay of reversible and irreversible degradation processes with different recovery dynamics was demonstrated to result in changes in the cell’s diurnal PCE dependence during its operational lifespan under real sunlight conditions.