We report on accelerated degradation testing of MAPbX3 films (X = I or Br) by exposure to concentrated sunlight of 100 suns and show that the evolution of light absorption and the corresponding structural modifications are dependent on the type of halide ion and the exposure temperature. One hour of such exposure provides a photon dose equivalent to that of one sun exposure for 100 hours. The degradation in absorption of MAPbI3 films after exposure to 100 suns for 60 min at elevated sample temperature (∼45-55 °C), due to decomposition of the hybrid perovskite material, is documented. No degradation was observed after exposure to the same sunlight concentration but at a lower sample temperature (∼25 °C). No photobleaching or decomposition of MAPbBr3 films was observed after exposure to similar stress conditions (light intensity, dose, and temperatures). Our results indicate that the degradation is highly dependent on the hybrid perovskite composition and can be light- and thermally enhanced.

Three‐dimensional (3 D) perovskite has attracted a lot of attention owing to its success in photovoltaic (PV) solar cells. However, one of its major crucial issues lies in its stability, which has limited its commercialization. An important property of organic–inorganic perovskite is the possibility of forming a layered material by using long organic cations that do not fit into the octahedral cage. These long organic cations act as a “barrier” that “caps” 3 D perovskite to form the layered material. Controlling the number of perovskite layers could provide a confined structure with chemical and physical properties that are different from those of 3 D perovskite. This opens up a whole new batch of interesting materials with huge potential for optoelectronic applications. This Minireview presents the synthesis, properties, and structural orientation of low‐dimensional perovskite. It also discusses the progress of low‐dimensional perovskite in PV solar cells, which, to date, have performance comparable to that of 3 D perovskite but with enhanced stability. Finally, the use of low‐dimensional perovskite in light‐emitting diodes (LEDs) and photodetectors is discussed. The low‐dimensional perovskites are promising candidates for LED devices, mainly because of their high radiative recombination as a result of the confined low‐dimensional quantum well.

The photochemical stability of encapsulated films of mixed halide perovskites with a range of MAPb(I Br ) (MA=methylammonium) compositions (solid solutions) was investigated under accelerated stressing using concentrated sunlight. The relevance of accelerated testing to standard operational conditions of solar cells was confirmed by comparison to degradation experiments under outdoor sunlight exposure. We found that MAPbBr films exhibited no degradation, while MAPbI and mixed halide MAPb(I Br ) films decomposed yielding crystallization of inorganic PbI accompanied by degradation of the perovskite solar light absorption, with faster absorption degradation in mixed halide films. The crystal coherence length was found to correlate with the stability of the films. We postulate that the introduction of Br into the mixed halide solid solution stressed its structure and induced more structural defects and/or grain boundaries compared to pure halide perovskites, which might be responsible for the accelerated degradation. Hence, the cause for accelerated degradation may be the increased defect density rather than the chemical composition of the perovskite materials.

No abstract

No abstract

No abstract

Accuratecharacterizationandreportingoforganicphotovoltaic(OPV)deviceperformanceremainsone\ud of theimportantchallengesinthe field. Thelargespreadamongtheefficiencies ofdeviceswiththesame\ud structure reportedbydifferentgroupsissignificantly causedbydifferentproceduresandequipment\ud used duringtesting.Thepresentedarticleaddressesthisissuebyofferinganewmethodofdevice\ud testing using “suitcase sample” approach combinedwithoutdoortestingthatlimitsthediversityofthe\ud equipment,andastrictmeasurementprotocol.Aroundrobinoutdoorcharacterizationofroll-to-roll\ud coated OPVcellsandmodulesconductedamong46laboratoriesworldwideispresented,wherethe\ud samples andthetestingequipmentwereintegratedinacompactsuitcasethatservedbothasasample\ud transportation toolandasaholderandtestequipmentduringtesting.Inaddition,aninternetbased\ud coordination wasusedviaplasticphotovoltaics.orgthatallowedfastandefficient communicationamong\ud participants andprovidedacontrolledreportingformatfortheresultsthateasedtheanalysisofthe\ud data. Thereporteddeviationsamongthelaboratorieswerelimitedto5%whencomparedtotheSi\ud referencedeviceintegratedinthesuitcaseandwereupto8%whencalculatedusingthelocalirradiance\ud data. Therefore,thismethodoffersafast,cheapandefficient toolforsamplesharingandtestingthat\ud allowsconductingoutdoormeasurementsofOPVdevicesinareproduciblemanner

We discuss the emerging perovskite incorporated tandem solar technology and high-throughput printing methods for this technology.