Electric field-induced "etching" of Cr film is a tip-based patterning technique that is used to create micro-and nano-sized trenches in the film under ambient conditions. The experimental data obtained in this study reveals that the etching of Cr occurs via the formation of water-soluble CrO 3 , which spontaneously forms at the cathode tip when a large electric field is applied using a pointed tip in the presence of humid air. By varying experimental conditions, such as vacuum level, gaseous environment, temperature, and humidity, the kinetics of the electric field induced chemical reaction at the cathode was studied. Subsequently, the obtained insights were incorporated into a model to explain the mechanism of the phenomenon. Water vapor in the air surrounding the tip acts as a limiting reactant in the electrochemical oxidation of Cr to CrO 3. Insights obtained from this study open new avenues for technological improvements in the patterning technique using this chemical method.
For quantification of curcumin content in turmeric, a low-cost multivariate-analysis-based sensing system is desired. It can be realized by exploiting the spectra in the visible region, which enables the use of off-the-shelf, relatively inexpensive light sources and detectors. To address this, we propose a novel decision-tree method for improved prediction accuracy. Two sets of models with PLSR algorithm are developed with the measured reflectance spectra from 66 turmeric samples in the range of 360–750 nm, and their respective curcuminoids content are quantified by HPLC. A suite of a coarse-model for initial prediction of turmeric samples in the broad range of 1%–4%, and five finer-models for subsequent prediction (in the ranges 1%–2%, 2%–3%, 3%–4%, 1.5%–2.5%, and 2.5%–3.5%) constitute the proposed decision-tree approach. The method’s efficacy is substantiated from an improved coefficient of determination (R 2) for the finer models (0.90–0.96) as compared to the coarse-model’s 0.92. This is further corroborated with lower RMSECV of 0.06–0.13 and an RMSEP of 0.15–0.25 for finer models, as compared to 0.219 and 0.45 for the coarse model, respectively. Testing reveals that the method results in 46% reduction in prediction error. Realization of a robust prediction approach in the visible range sets the stage for the development of cost-effective field-deployable devices for on-site measurement of curcumin.
On-site material inspection and quality analysis of food and agricultural produce require portable sensing systems. We report the development of a miniaturized spectrometer with an integrated light source operating in the visible and near-infrared range, for chemometrics based material-sensing applications. The proposed system uses off-the-shelf light source and detector. The electronic circuit is designed, developed, and tested in-house. To validate the system’s usability, a set of classification experiments are carried out with measured spectra from culinary white powders and medicinal pills. Several classification algorithms are used to build predictive models and the best-suited ones give prediction accuracies of 80% and 92.6% respectively. A regression model built to estimate the curcumin content in turmeric shows a coefficient-of-determination of 0.97 for prediction. With more than 90% repeatability in the measured reflectance spectra, robustness of the device is demonstrated. Realization of a portable spectrometer, along with a framework for building appropriate prediction models, is expected to spur the development of point-of-use material sensing in the Vis-NIR range.
Introduction The combination of a light source emitting a desired wavelength range and a detector capturing that signal can help understand the photonic interaction of matter in different regions of the electromagnetic spectrum. The reflectance spectra of the same analyte will vary based on which region of the electromagnetic spectrum it is captured in. In conjunction with machine learning applications, several parameters of the analyte can be simultaneously analyzed and reported. In this study, we have attempted to compare chemometric models for predicting the quantity of total curcuminoids (sum of bisdemethoxycurcumin, demethoxycurcumin and curcumin) in powdered turmeric samples using diffused reflectance spectroscopy, in two regions of the electromagnetic spectrum: (1) The visible range (360-750 nm), and (2) A small region of the near-infrared (NIR) range (1550-1950 nm). Materials and Methods The diffused reflectance spectra of turmeric powders (n = 66) are captured using two different spectrometers — JAZ from Ocean optics for the visible range, and Spectral Engines for the NIR range. The quantity of total curcuminoids in this data set ranges between 1-4%. The spectra from each instrument are subjected to a series of pre-processing steps to condition the data. The pre-processing steps were optimized to obtain the best-possible accuracy in the subsequent regression models. Principal Component Analysis (PCA) is used to qualitatively analyze the data and visualize the clustering patterns, if any. The processed spectra are then evaluated with Partial Least Squared Regression algorithm (PLSR), using High Performance Liquid Chromatography (HPLC) as the reference data, to predict the quantity of curcuminoids in powdered turmeric samples. The model performance is reported with coefficient of determination (R2 ), root-mean-squared error of cross validation (RMSECV) and root-mean-squared error of prediction (RMSEP). Results and Discussions The spectrum of turmeric has a single broad peak in the visible region (360-750 nm), owing to the electronic transitions in the curcumin molecule. There are two peaks observed in the NIR region (1550-1950 nm), corresponding to the first overtone of the C-H stretching vibrations and second overtone of the C=O stretching vibrations in turmeric. On subjection to PCA, there is a subtle clustering when the spectra are divided into 1% curcumin slabs in the visible range, as seen in Fig. 2(a). However, there is no such separation seen for spectra collected in the NIR region. On building regression models based on this data, the model with the visible spectra of turmeric has a better R2 of 0.921 as compared to 0.83 for the NIR spectra. Similarly RMSECV is found to be 0.219 (visible), 0.273 (NIR) and RMSEP as 0.302 (visible), 0.352 (NIR) (Fig. 3). The model for the visible spectra performs better both qualitatively and quantitatively. Both the models are also validated on a test data set of 7 samples (not a part of the training data), and the predicted results are shown in Fig. 4. The predicted curcuminoid values from 7 samples have a mean deviation of 7.7% and 11% from the model based on visible and NIR spectra of turmeric, respectively, when compared with the actual curcuminoid values from HPLC. Conclusion The chemometric model built with the spectra of turmeric in the visible range performs better than its NIR counterpart with the same set of turmeric samples. This observation implies that the cost of a chemometric sensing system to predict total curcuminoids in turmeric can be reduced by using the visible wavelength range due to the relatively lower cost of detectors and light sources. However, this is a preliminary study with limited number of samples to conclusively say which region of the electromagnetic spectrum is better for analyzing and predicting total curcuminoids in turmeric. Upon further addition of samples and exploring different machine learning approaches, a stronger conclusion can be drawn. References H. Suresh, A. R. Behera, and R. Pratap, ECS Meet. Abstr., MA2020-01, 1858–1858 (2020) https://iopscience.iop.org/article/10.1149/MA2020-01261858mtgabs Figure 1
The phenomena of leader inception and propagation leading to breakdown in strongly attaching gases like SF6 are currently being studied because of their relevance to the design of High Voltage Gas Insulated Systems (CIS).Breakdown of SF6 gas under inhomogeneous fields is known to be by the leader mechanism. The leader propagation is guided by the electric field at the leader tip, which inturn is dependent on the nature of voltage applied, electrode geometry and charge distributed in the leader. The charge build up process in the leader is governed by Resistive-Capacitive (R-C) transient fields. In such fields, both permittivities and conductivities of the participating medium determine the field distribution. The scope of the present paper is to discuss the important aspects of computing R-C transient field associated with the leader in SF6 gas modeled as a straight cylindrical conducting channel. Studies are carried out under unit step voltage excitation for two leader lengths and assumed conductivity of the leader. The workability of the R-C transient field computing algorithm for such studies carried out with the help of a Laplace solver are presented and discussed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.