Abstract. Rare-earth-barium-copper-oxide (REBCO) tapes are now available from several industrial manufacturers and are very promising conductors in high field applications. Due to diverging materials and deposition processes, these manufacturers' tapes can be expected to differ in their electro-mechanical and mechanical properties. For magnets designers, these are together with the conductors' in-field critical current performance of the highest importance in choosing a suitable conductor. In this work, the strain and stress dependence of the current carrying capabilities as well as the stress and strain correlation are investigated for commercial coated conductors from Bruker HTS, Fujikura, SuNAM, SuperOx and SuperPower at 77 K, self-field and 4.2 K, 19 T.

Scaling relations describing the electromagnetic behaviour of coated conductors (CCs) greatly simplify the design of REBCO-based devices. The performance of REBCO CCs is strongly influenced by fabrication route, conductor architecture and materials, and these parameters vary from one manufacturer to the others. In the present work we have examined the critical surface for the current density, Jc(T,B,), of coated conductors from six different manufacturers: American Superconductor Co. (US), Bruker HTS GmbH (Germany), Fujikura Ltd. (Japan), SuNAM Co. Ltd. (Korea), SuperOx ZAO (Russia) and SuperPower Inc. (US). Electrical transport and magnetic measurements were performed at temperatures between 4.2 K and 77 K and in magnetic field up to 19 T.Experiments were conducted at three different orientations of the field with respect to the crystallographic c-axis of the REBCO layer, θ = 0°, 45° and 90°, in order to probe the angular anisotropy of Jc. In spite of the large variability of CCs' performance, we show here that field and temperature dependences of Jc at a given angle can be reproduced over wide ranges using a scaling relation based only on three parameters. Furthermore, we present and validate a new approach combining magnetic and transport measurements for the determination of the scaling parameters with minimal experimental effort.

With the aim of clarifying the relationship between lattice deformations and superconducting properties of Nb3Sn technological wires we have carried out high-energy x-ray diffraction experiments at the European Synchrotron Radiation Facility (ESRF) in Grenoble on individual samples of multi-filamentary internal-tin-type Nb3Sn wires. In particular, a test probe developed at the University of Geneva allowed us to perform these experiments at 4.2 K, while applying an axial tensile load to the specimen. In this way, the lattice parameter values of all the constituents (Nb3Sn, Nb, Cu) were determined, in both the parallel and orthogonal directions with respect to the applied load axis, as a function of the applied strain. The experiments were performed on industrial wires, which were reinforced by a stainless steel outer tube, applied before the Nb3Sn reaction heat treatment, in order to evaluate the effect of an additional pre-compression strain. The relation between the microscopically determined crystalline lattice deformations and the measured applied strain is discussed as a basis for the analysis of the superconducting performances of Nb3Sn wires subject to mechanical loads.

Nowadays there is a great deal of interest in the scientific community in developing nextgeneration accelerator magnets based on high-J c Nb 3 Sn Rutherford cables. Inside a cable the wires are subjected to the combined effect of axial and transverse load. Since Nb 3 Sn is a strain sensitive material, electromechanical characterization of cables is essential for magnet design. Testing a full-size Rutherford cable is an extremely complex and involved task. For this reason special Walters springs have been developed at the University of Geneva to test single wires under longitudinal and transverse load. In this work we analyze three PIT wires under transverse compressive load. To better understand the experimental results, a finite element model was developed. This model enabled better understanding of the mechanical behavior of the three samples and investigation of the mechanisms that determine wire performance degradation upon loading.

The critical current of an internal tin Nb 3 Sn wire developed by Oxford Instruments, Superconducting Technology for International Thermonuclear Experimental Reactor ͑ITER͒ ͑OST type-I, billet No. 7567͒ has been studied under axial strain at fields between 12 and 19 T at 4.2 K. Simulating the situation in a cable in conduit, where thermally induced compressive strain is important, a single wire ͑strand͒ was jacketed with AISI 316L stainless steel. The reinforced wire shows an important increase in m , the applied strain where I c reaches its maximum, from 0.25% to 0.57%. In addition the irreversibility limit, irr , is improved from 0.50% applied strain to Ͼ1.10%. It could also be shown that the I c at zero intrinsic strain is almost identical. This demonstrates that jacketing does not influence the physical parameters of the original wire. Experimental data of the bare wire has been well fitted by different strain functions. However, it was not possible to model the data of the jacketed wire. There are indications that only models which take into account the multidimensional character of strain are able to describe the behavior but further development is required.

No abstract

High-performance Nb3Sn conductors are intended to be used in large-scale magnets like the International Thermonuclear Experimental Reactor (ITER) and in the upgrade of the Large Hadron Collider (LHC). Due to the occurrence of high electromagnetic forces, a detailed knowledge of the response of the critical current to the three-dimensional mechanical loads acting on the wires inside the cables is required. A detailed analysis of transverse stress effects on the critical current for powder-in-tube and bronze route Nb3Sn wires is presented. In an earlier publication, we have described the effect of transverse stress exerted on a Nb3Sn wire by means of two parallel plates. In the present paper, we analyse the effect of transverse stress exerted simultaneously by four walls on a wire being confined in a U-shaped groove. In order to get a more realistic picture of the situation of wires embedded in a Rutherford cable, the compression by four walls was also performed after impregnating the wire with epoxy in the same U-shaped groove. The result is very different from the case of pressing by means of two walls: the effect of pressure on Ic is now strongly reduced, which is attributed to the almost hydrostatic pressure in the U-shaped groove. This is further confirmed by the comparison between the effects of axial and transverse loads on the upper critical field and the pinning force. The present data are also compared against the effects of mechanical load on the critical current of cables in large-scale magnets.

The full-matrix set of combined temperature (4.2–14 K) and applied axial strain (εa) data for the bulk pinning force of a technological Nb3Sn wire (OST type-I) has been studied at fields up to 19 T by combining transport (variable εa) and magnetic (variable T) measurements. Some length of the wire was also jacketed with AISI 316L stainless steel, in order to apply a radial strain and to simulate the thermally induced axial compressive strain that the Nb3Sn wires experience in a cable-in-conduit-conductor (CICC). Within the framework of the unified scaling law, raw scaling data for the effective upper critical field, , have been used in order to experimentally determine the strain function, s(ε), of both the bare and the jacketed wires. A direct testing of the various proposed models for s(ε) has been carried out, including the power law, the deviatoric description and the polynomial form. All models adequately fit to the s(ε) of the bare wire, but in the jacketed wire none of them is able to describe the tensile strain region above the Ic maximum, where the enhanced radial compression cannot be neglected. The origin of the onset of a reduced Bc2 is also discussed.