Abstract. Rare-earth-barium-copper-oxide (REBCO) tapes are now available from several industrial manufacturers and are very promising conductors in high field applications. Due to diverging materials and deposition processes, these manufacturers' tapes can be expected to differ in their electro-mechanical and mechanical properties. For magnets designers, these are together with the conductors' in-field critical current performance of the highest importance in choosing a suitable conductor. In this work, the strain and stress dependence of the current carrying capabilities as well as the stress and strain correlation are investigated for commercial coated conductors from Bruker HTS, Fujikura, SuNAM, SuperOx and SuperPower at 77 K, self-field and 4.2 K, 19 T.

Scaling relations describing the electromagnetic behaviour of coated conductors (CCs) greatly simplify the design of REBCO-based devices. The performance of REBCO CCs is strongly influenced by fabrication route, conductor architecture and materials, and these parameters vary from one manufacturer to the others. In the present work we have examined the critical surface for the current density, Jc(T,B,), of coated conductors from six different manufacturers: American Superconductor Co. (US), Bruker HTS GmbH (Germany), Fujikura Ltd. (Japan), SuNAM Co. Ltd. (Korea), SuperOx ZAO (Russia) and SuperPower Inc. (US). Electrical transport and magnetic measurements were performed at temperatures between 4.2 K and 77 K and in magnetic field up to 19 T.Experiments were conducted at three different orientations of the field with respect to the crystallographic c-axis of the REBCO layer, θ = 0°, 45° and 90°, in order to probe the angular anisotropy of Jc. In spite of the large variability of CCs' performance, we show here that field and temperature dependences of Jc at a given angle can be reproduced over wide ranges using a scaling relation based only on three parameters. Furthermore, we present and validate a new approach combining magnetic and transport measurements for the determination of the scaling parameters with minimal experimental effort.

With the aim of clarifying the relationship between lattice deformations and superconducting properties of Nb3Sn technological wires we have carried out high-energy x-ray diffraction experiments at the European Synchrotron Radiation Facility (ESRF) in Grenoble on individual samples of multi-filamentary internal-tin-type Nb3Sn wires. In particular, a test probe developed at the University of Geneva allowed us to perform these experiments at 4.2 K, while applying an axial tensile load to the specimen. In this way, the lattice parameter values of all the constituents (Nb3Sn, Nb, Cu) were determined, in both the parallel and orthogonal directions with respect to the applied load axis, as a function of the applied strain. The experiments were performed on industrial wires, which were reinforced by a stainless steel outer tube, applied before the Nb3Sn reaction heat treatment, in order to evaluate the effect of an additional pre-compression strain. The relation between the microscopically determined crystalline lattice deformations and the measured applied strain is discussed as a basis for the analysis of the superconducting performances of Nb3Sn wires subject to mechanical loads.

Nowadays there is a great deal of interest in the scientific community in developing nextgeneration accelerator magnets based on high-J c Nb 3 Sn Rutherford cables. Inside a cable the wires are subjected to the combined effect of axial and transverse load. Since Nb 3 Sn is a strain sensitive material, electromechanical characterization of cables is essential for magnet design. Testing a full-size Rutherford cable is an extremely complex and involved task. For this reason special Walters springs have been developed at the University of Geneva to test single wires under longitudinal and transverse load. In this work we analyze three PIT wires under transverse compressive load. To better understand the experimental results, a finite element model was developed. This model enabled better understanding of the mechanical behavior of the three samples and investigation of the mechanisms that determine wire performance degradation upon loading.

The critical current of an internal tin Nb 3 Sn wire developed by Oxford Instruments, Superconducting Technology for International Thermonuclear Experimental Reactor ͑ITER͒ ͑OST type-I, billet No. 7567͒ has been studied under axial strain at fields between 12 and 19 T at 4.2 K. Simulating the situation in a cable in conduit, where thermally induced compressive strain is important, a single wire ͑strand͒ was jacketed with AISI 316L stainless steel. The reinforced wire shows an important increase in m , the applied strain where I c reaches its maximum, from 0.25% to 0.57%. In addition the irreversibility limit, irr , is improved from 0.50% applied strain to Ͼ1.10%. It could also be shown that the I c at zero intrinsic strain is almost identical. This demonstrates that jacketing does not influence the physical parameters of the original wire. Experimental data of the bare wire has been well fitted by different strain functions. However, it was not possible to model the data of the jacketed wire. There are indications that only models which take into account the multidimensional character of strain are able to describe the behavior but further development is required.